THIS MANUAL HAS BEEN PREPARED FOR PERSONNEL QUALIFIED TO INSTALL
ELECTRICAL EQUIPMENT, WHO SHOULD PERFORM THE INITIAL FIELD ST ARTUP AND ADJUSTMENTS OF THE EQUIPMENT COVERED BY THIS MANUAL.
Vulcan Ovens are produced with quality
workmanship and material. Proper
installation, usage, and maintenance of
your oven will result in many years of
satisfactory performance.
The Vulcan Cook & Hold Oven is more
than just an oven – it’s a “System”;
precisely controlled heat, regulated to
retain ascorbic acid and maximize the
nutritional value, taste and eye-appeal
of food. In this environment, virtually
any food product can be prepared to
delicious perfection in just ONE oven!
“System” food preparation eliminates
the need for multiple ovens with
duplicate features.
This manual is provided to assist
persons responsible for the operation
and maintenance of the oven with a
simple, but comprehensive understanding of its proper use. We
recommend that you thoroughly read
this entire manual and carefully follow all
of the instructions provided prior to
placing the oven into operation.
As with any piece of food service
equipment, this oven system requires a
minimum of care and maintenance.
Recommended procedures are
contained in this manual and should
become a regular part of the operation
of the unit.
The Vulc an Cook & Hold Oven is the
right choice for low temperature food
preparation.
PRINCIPLES OF
COOK & HOLD OVENS
Vulcan Cook & Hold Ovens are
designed and perfected for cooking at a
lower temperature. The principles of
Low Temperature Cooking and Holding
can be summarized into several
objectives: increased product yields,
increased profits from increased
yields, increased moisture retention,
increased tenderization, and
consistency of doneness.
When the Vulcan Cook & Hold Oven
finishes the cooking cycle, it
automatically switches to the hold cycle.
Throughout this manual we recommend
holding temperatures such as 140⁰F
(60⁰C). This temperature refers to the
oven’s hold temperature setting and not
to the internal temperature of the food
being roasted. The internal product
temperature will run below the hold
temperature. (For example: roast beef
held at 140⁰F will be about 130⁰F
internally or medium rare.)
All meat products contain enzymes.
These enzymes perform the
important function of tenderizing the
meat when they reach temperatures
of 100⁰F (38⁰C) to 140⁰F (60⁰C). As
these enzymes are heated, they break
down the connective tissue that is
inherent in all red meat products.
The hold cycle allows this natural
tenderization process to proceed in an
orderly manner. As long as the internal
3
VRH SERIES OVENSF-41207 (11-12)
temperature of the meat does not
exceed 140⁰F, the process will continue.
Once the temperature reaches 140⁰F
the process will stop, because the
enzymes will be deactivated.
This tenderization process makes the
meat more flavorful. It is similar to aging
meat before it is sold. The longer the
hold, the higher degree of tenderization.
Each hour of holding is equal to one
day of aging.
BENEFITS OF
COOK & HOLD OVENS
Superior Results: Low temperature
roasting has been recognized as the
best method for preparing meat and
poultry because of increased
tenderness, more even roasting, and a
juicer product.
Increased Sales: You will attract more
customers and have more repeat
business because you are now
producing a superior product in your
market area. All of your products will be
unique, from prime rib and chicken to
BBQ ribs, pork roasts, and even bakery
items!
Reduced Energy Costs: It costs
significantly less to run a Vulcan Cook &
hold Oven instead of a conventional
oven. Also, in most areas, no exhaust
hood is needed.
Reduced Shrinkage of Product: You
can cut your percent of shrinkage from
25 to 30% down to 5 to 10%. This
means more servings to sell to your
customers! The Vulcan Cook & Hold
Oven can pay for itself in just months,
depending on your volume.
Reduced Labor Cost: Your cooks do
not have to come in early to put roasts
in or stay late to take them out of the
oven. Holding banquet foods in a
Vulcan Cook & Hold Oven reduces that
last minute party prep to almost nothing.
COMPARISON OF
COOK & HOLD OVENS
“The Comparison Stops Here” –
more than a catchy slogan, it’s a fact.
Convection ovens, unlike Vulcan Cook
& Hold Ovens, blast high temperature
dry air over the product. The end result
with convection oven cooking is
excessive and unnecessary shrinkage.
Vulcan Cook & Hold Oven Systems:
1. Offer a lifetime heating element
warranty.
2. Provide a natural roasted
brown, caramelized product
without coloring agents.
“You can taste the difference.”
3. Do not require a ventilation
hood. (See pg. 5)
4. Are accurate, plus or minus 5⁰F.
5. Are easy to clean.
6. Have stainless steel constructioninside and out.
4
VRH SERIES OVENSF-41207 (11-12)
INSTALLATION
Before installing, verify that the
electrical service agrees with the
specifications on the rating plate
located on the lower back corner of
the oven. (Fig. 4) If the supply and
equipment requirements do not agree,
do not proceed with unpacking and
installation. Contact your Vulcan
Customer Service Department
immediately.
UNPACKING:
The oven was inspected before leaving
the factory. The transportation company
assumes full responsibility for safe
delivery upon acceptance of the
shipment. Immediately after unpacking,
check for possible shipping damage to
the oven.
If the oven is found to be damaged,
save the packaging material and
contact the carrier within 15 days of
delivery.
Carefully unpack and place in a work
accessible area as near the installation
position as possible.
1. Open oven door(s) and remove
packing material.
2. Check under oven or separate
package for racks, pans, etc.
3. Peel off vinyl protection film from
oven.
CLEANING:
The oven should be thoroughly cleaned
prior to putting into service. Refer to
cleaning instructions in this manual.
LOCATION:
For efficient oven operation, choose a
location that will provide easy loading
and unloading without interfering with
the final assembly of food orders. The
installation location must allow adequate
clearances for servicing and proper
operation.
VRH88
The VRH88 oven is simply two (2)
VRH8 ovens stacked on top of each
other. One (1) oven will come with a
caster kit and a stacking assembly on
top. The oven without casters is
placed inside the stacking assembly.
VENTILATION HOOD
REQUIREMENTS
Some local State Codes require the use
of a ventilation hood for equipment
operating in excess of 250⁰F. Many will
allow operation of Rethermalization
Ovens at lower temperatures. Please
contact a Service Agency to modify this
parameter, if needed to meet local State
Codes.
5
VRH SERIES OVENSF-41207 (11-12)
ELECTRICAL REQUIREMENTS
ELECTRICAL CODES & STANDARDS:
The oven must be installed in
accordance with:
In the United States of America:
1. State and Local Codes.
2. National Electrical Code, ANSI/
NFPA-70 (latest edition.) Copies
may be obtained from: The
National Fire Protection
Association, 1Batterymarch Park,
Quincy, MA 02269.
1-617-770-3000 www.nfpa.org
In Canada:
1. Local Codes.
2. Canadian Electrical Code, CSA
C22.1 (latest edition.) Copies
may be obtained from: The
Canadian Standard Association.
www.csa.ca
ELECTRICAL CONNECTIONS:
The oven is factory wired for single
phase 208/240 volt or three phase
operation. All ovens are equipped with
a 6 foot cord and NEMA 6-15, 6-30, 650, or a 15-30 plug as standard
equipment. (Fig. 3)
.
(Fig.3)
Refer to wiring diagrams and
Specification Chart in the back of this
manual.
The cord and plug supplied is a suitable
durable cord with a proper strain relief.
SERIAL DATA PLATE
(Fig. 4)
6
VRH SERIES OVENSF-41207 (11-12)
OPERATION
CONTROLS
The Oven and its parts
are hot. Be very careful when operating,
cleaning, or servicing the oven.
All operating controls are located on the
front Control Panel(s). The oven is
supplied with individual operating
controls for each oven cav i ty.
POWER
THERMOMETER COOKING TIME ON / OFF
KNOB SWITCH
temperature of the oven.
Cooking Time Knob: Sets the desired
cooking time from ½ hour to 12 hours.
Power ON/OFF Switch: Turns the
oven On or Off.
Cooking Temperature Knob: Sets the
desired cooking temperature.
Cooking Mode Light: Indicates oven is
in Cooking Mode.
Holding Mode Light: Indicates oven is
in Holding Mode.
Holding Temperature Knob: Sets t he
desired holding temperature.
BEFORE FIRST USE
The Oven and its parts
are hot. Be very careful when operating,
cleaning, or servicing the oven.
1. Thoroughly clean the oven
before initial use. Please refer
to cleaning instructions in this
manual.
2. Test the oven to verify that the
oven operates normally. Please
refer to “Testing The Oven”
procedure in this manual.
TESTING THE OVEN
The Oven and its parts
are hot. Be very careful when operating,
cleaning, or servicing the oven.
Before using the oven for the first time,
verify that the oven operates normally.
1. Check that the oven is connected
to the correct power source.
2. Set the COOKING TIME knob to 0.
3. Turn the HOLDING TEMP ERATURE knob to 140⁰ F.
4. Set Power ON/OFF Switch to
ON position.
5. Check that the Oven Circulating
Fan(s) are running.
7
VRH SERIES OVENSF-41207 (11-12)
6. Check that the Holding
Temperature Indicator Light is
illuminated.
Each Oven is equipped with cooling
fans. The cooling fans may not operate
when the oven is first turned on. The
cooling fans operate only when the
thermostat, to which they are
connected, requires it.
7. Set the COOKING TIME knob to 2 hours. The Holding
Temperature Indicator Light will
go out and the Cooking
Temperature Indicator Light will
illuminate.
8. Turn the COOKING TEMP- ERATURE knob to 250⁰ F.
Check the interior rear of the
oven cavity to determine that the
oven is heating.
9. Turn the COOKING TIME KNOB
to 0 and set the HOLDINGTEMPERATURE knob at 250⁰ F.
10. Check that the Cooking
Temperature Indicator Light has
gone out and the Holding
Temperature Indicator Light has
illuminated.
11. Check the interior rear of the
oven to ensure that the oven is
heating. If all the functions
perform satisfactorily, the oven is
ready for operation.
OPERATING INSTRUCTIONS
The Oven and its parts
are hot. Be very careful when operating,
cleaning, or servicing the oven.
1. Turn Cooking temperatureknob to desired Cooking
temperature.
2. Set Cooking timer knob(s) to
desired cooking time to include30 to 60 minute preheat time.
3. Turn Holding Temperature knob
to desired holding temperature.
4. Turn On/Off Switch to ON position. On/Off indicator Light
and Holding Temperature Light
w ill illuminate.
When the oven reaches the desired
cooking temperature it is ready for use.
Keep the oven door closed during the
preheating cycle.
8
VRH SERIES OVENSF-41207 (11-12)
SHUTDOWN
The Oven and its parts
are hot. Be very careful when operating,
cleaning, or servicing the oven.
1. Turn Holding Temperature knob
and Cooking Temperatureknob counter-clockwiseuntil
they stop at the Off position..
2. Open door slightly to allow
ventilation and cool down period.
This is to allow oven to
properly cool down so
components are not
damaged.
Wait 15 minutes before turning
On/Off Switch to OFF because the
cooling fans need to operate during the
cool-down period.
3. Turn On/Off Switch to OFFposition.
The cooling fans will automatically turn
off when the proper cool-down
temperature is reached.
EXTENDED SHUTDOWN
The Oven and its parts
are hot. Be very careful when operating,
cleaning, or servicing the oven.
Perform the following procedure to shut
down the oven for an extended period of
time.
1. Perform the SHUTDOWNprocedure.
2. Unplug the oven.
3. Thoroughly clean the ovenaccording to the cleaning
procedures in this manual.
4. Leave the door(s) slightly opento allow ventilation and
preservation of the gasket(s).
9
VRH SERIES OVENSF-41207 (11-12)
MAINTENANCE
CLEANING
The Oven and its parts
are hot. Be very careful when operating,
cleaning, or servicing the oven.
Always unplug
electrical power supply before
cleaning.
Avoid splashing water into upper
areas of the oven to prevent damage
to electrical components or
connections.
Never spray the unit with a hose.
Never use harsh chemicals or
abrasive pads to clean the oven.
DAILY:
1. Unplug electrical power supply.
2. Allow oven to go through cool down period before cleaning.
3. Remove the Interior Side Racks
4. Take the Interior Side Racks to a
sink or dishwasher for a thorough
cleaning. Use a mild soap and
water solution to clean these
items.
5. If necessary, clean the interior of
the oven with a damp cloth.
Wipe dry with a soft dry cloth.
6. Reasse mble oven.
7. Clean the exterior of the oven
with a clean damp cloth.
HEAVY-DUTY CLEANING:
For heavy-duty cleaning, use warm
water, a degreaser, and a plastic,
stainless steel, or scotch-brite pad.
Never rub in a circular motion. Always
rub gently in the direction of the steel
grain. Rinse thoroughly and wipe dry
with a soft cloth.
STAINLESS STEEL CARE
CLEANING:
Stainless Steel contains 70 – 80% iron,
which will rust if not properly maintained.
Stainless Steel also contains 12 – 30%
chromium, which forms an invisible
passive, protective film that shields
against corrosion.
If the protective film remains intact, the
stainless steel will remain intact.
However, if the film is damaged, the
stainless steel can break down and rust.
PREVENTIVE CARE:
To prevent stainless steel breakdown, follow these steps:
1. Never use any metal tools,
scrapers, files, wire brushes,
or scouring pads (except for
stainless steel scouring pads,)which will mar the surface.
10
VRH SERIES OVENSF-41207 (11-12)
2. Never use steel wool – which will leave behind particles that will
rust.
3. Never use acid-based or
chloride containing cleaning
solutions – which will break
down the protective film.
4. Never rub in a circular motion.
Always rub gently in the direction
of the steel grain.
5. Never leave any food products or salt on the surface. Many
foods are acidic. Salt contains
chloride.
PRESERVING & RESTORING:
Special stainless steel polishing
cleaners can preserve and restore the
protective film.
Preserve the life of stainless steel with a
regular application of a high-quality
stainless steel polishing cleaner, as a
final step to daily cleaning.
If signs of breakdown appear, restore
the stainless steel surface. First,
thoroughly clean, rinse, and dry the
surface. Then, on a daily basis, apply a
high-quality stainless steel polish
according to manufacturer’s instructions.
HEAT TINT:
Darkened areas, called “heat tint,” may
appear on stainless steel exposed to
excessive heat. Excessive heat causes
the protective film to thicken. This is
unsightly, but is not a sign of permanent
damage.
To remove heat tint, follow the routine
cleaning procedure. Stubborn heat tint
will require heavy-duty cleaning. To
reduce heat tint, limit the exposure of
equipment to excessive heat.
DOOR GASKET CARE
DOOR GASKET:
At least once a week, thoroughly check
the door gasket for damage/wear. A
damaged gasket can cause inefficient
and unsatisfactory operation of the
oven.
If the gasket requires cleaning:
1. Gently wash gasket using a
moist cloth, a mild detergent
solution, and warm water.
2. Rinse with a fresh cloth
moistened in warm water to
remove all traces of detergent.
3. Gently wipe dry with a clean dry
cloth.
Never apply food oils, or petroleum
lubricants directly to the gasket(s).
Petroleum based solvents and
lubricants will reduce the gasket’s life.
11
VRH SERIES OVENSF-41207 (11-12)
COOKING
INTRODUCTION
This cooking guide has been produced
for your Vulcan Cook & Hold Oven
System. It should be used as a handy
reference when using your oven. The
guide has been developed to help
answer questions which you may have
relating to product preparation as well
as making you familiar with the
operation of your Cook & Hold Oven.
When using your oven, experiment with
your own house specialties. The degree
of doneness varies based upon
individual preferences. These
preferences can be easily accomplished
by varying the recommended time
guidelines in this manual. The
guidelines which are presented in this
manual are suggested and have been
tested to insure product preparation as
indicated.
The concept of “Low Temperature
Cooking” is not a science, it is an art.
Chefs from around the world vary in
terms of the doneness and appearance
in the products which they prefer.
Therefore, we suggest first
understanding what your Oven System
will do for the multitude of applications
available to you.
COOKING RACK
Depending upon the size of the Cook &
Hold Oven, each unit is supplied with a
specially designed cooking rack(s). The
cooking rack must be used when
cooking food products to insure absolute
product quality and integrity.
The cooking rack is simply placed inside
a standard 18” x 26” sheet tray (2/1
Gastronome) and the product which is
to be cooked and held is placed on top
of the cooking rack. When more than
one product is being prepared, the food
products should not be cramped
together onto one cooking rack.
Sufficient room should separate the
products on a single cooking rack to
insure proper circulation of air around
the product.
When loading the oven, an additional
18” x 26” sheet tray, in an inverted
position, (Fig. 5) should be placed
directly above the food product being
prepared. This creates the necessary
air flow pattern to produce highly
desirable carmelization and uniform
roasting of the product.
INVERTED SHEET TRAY
Fig. 5
A helpful hint when loading your food
product on the cooking rack is to either
line your 18” x 26” sheet tray with foil, or
spray with a quality vegetable oil. This
helps with easy clean up after use.
12
VRH SERIES OVENSF-41207 (11-12)
PRODUCT
WEIGHT
TIME
TEMP.
HOLD TIME
TEMP.
TEMP.
GUIDELINES
Prime Rib
20 lbs.
5 hrs.
225⁰ F
4 hrs. min.
2 per shelf
Boneless Rib eye
12 lbs.
3 hrs
225⁰ F
4 hrs. min.
3 per shelf
Top Round
(USDA
18-20 lbs.
4½-5 hrs.
225⁰ F
4 hrs. min.
140⁰ F
130⁰ F
2 per shelf
Steamship Round
(USDA
60 lbs.
10 hrs.
225⁰ F
4 hrs. min.
140⁰ F
130⁰ F
1 per shelf
Bottom Round
(USDA
20 lbs.
5 hrs.
225⁰ F
8 hrs. min.
140⁰ F
130⁰ F
2 per shelf
Boneless Strip Loin
(USDA
12 lbs.
3 hrs.
225⁰ F
4 hrs. min.
140⁰ F
130⁰ F
3 per shelf
Whole Tenderloin
(USDA
Top Sirloin Butt
(USDA
Beef Short Ribs
10 lbs.
4 hrs.
225⁰ F
4 hrs. min.
155⁰ F
165⁰ F
1 per shelf
Cubed Steaks
10 lbs.
4 hrs.
225⁰ F
3 hrs. min.
1 tray per shelf
Beef Back Ribs
30 lbs.
6 hrs.
225⁰ F
4 hrs.
4 per shelf
Beef Stew
10 lbs.
4 hrs.
225⁰ F
6 hrs. min.
1 tray per shelf
Corned Beef
Frozen Burgers
7-8 lbs.
45 min.
225⁰ F
4 hrs. max
150⁰ F
165⁰ F
24 per shelf
Fresh Ham
12 lbs.
6 hrs.
250⁰ F
4 hrs.
160⁰ F
165⁰ F
2 per shelf
Cooked Cured Ham
12 lbs.
4 hrs.
250⁰ F
4 hrs.
2 per shelf
Pork Back Ribs
10 lbs.
4 hrs.
250⁰ F
3 hrs. max.
6 slabs per shelf
Pork Spare Ribs
250⁰ F
Fresh Sausages
10 lbs.
2 hrs.
225⁰ F
5 hrs. max
160⁰ F
175⁰ F
10 lbs. per shelf
Pre-Cooked Sausage
10 lbs.
1¾ hr.
250⁰ F
5 hrs. max
160⁰ F
160⁰ F
10 lbs. per shelf
Roast Suckling Pig
30 lbs.
6 hrs.
250⁰ F
3 hrs. min.
1 per shelf
COOKING AND HOLDING GUIDE
Please note that as products vary, as well as other elements such as altitude, so
shall actual cooking times and temperatures. These should be adjusted as
needed based upon your actual experience. Finished product temperatures
should be verified manually, prior to serving, in order to insure food safety.
(DETAILS)
(USDA
#109)
(USDA
#112A)
#168)
COOK
COOK
HOLD
140⁰ F 135⁰ F
140⁰ F 135⁰ F
MAX.
INTERNAL
LOADING
#160)
#170)
#180)
#190)
10 lbs.
#184)
12-14 lbs.
(Stew Meat)
12 lbs. 4 hrs. 250⁰ F 4 hrs. min.
(USDA
#422)
30 lbs. 4 hrs.
2½ hrs.
3 hrs.
225⁰ F
225⁰ F
2 hrs. min.
4 hrs. min.
4 hrs.
140⁰ F 130⁰ F
140⁰ F 135⁰ F
160⁰ F 160⁰ F
160⁰ F 160⁰ F
150⁰ F 175⁰ F
150⁰ F 165⁰ F
160⁰ F 135⁰ F
160⁰ F 175⁰ F
160⁰ F 175⁰ F
4 per shelf
3 per shelf
2 per shelf
5 slabs per shelf
160⁰ F 170⁰ F
13
VRH SERIES OVENSF-41207 (11-12)
PRODUCT
WEIGHT
TIME
TEMP.
HOLD TIME
TEMP.
MAX.
TEMP.
GUIDELINES
Chicken Pieces
10 lbs.
2¼ hrs.
250⁰ F
1 hr. max.
150⁰ F
170⁰ F
10 lbs. per shelf
Whole Chickens
20 lbs.
2½ hrs.
250⁰ F
5 hrs. max
150⁰ F
170⁰ F
6 per shelf
Whole Tu rkeys
20 lbs.
4½ hrs.
250⁰ F
5 hrs. max.
2 per shelf
Rack of Lamb
18 lbs.
3½ hrs.
250⁰ F
3 hrs. max
140⁰ F
140⁰ F
15 racks per shelf
Braised Lamb Shanks
10-12 lbs.
4 hrs.
250⁰ F
4 hrs. min.
1 tray per shelf
Fish Filets
10 lbs.
40 min.
225⁰ F
4 hrs. max
10 lbs. per shelf
Clear Soups
250⁰ F
Rice
1 Quart Dry
2 hrs.
250⁰ F
18 hrs. max
150⁰ F
160⁰ F
1 pan per shelf
Frozen Entrees
1 Quart Dry
3 hrs.
250⁰ F
Overnight
160⁰ F
165⁰ F
2 pans per shelf
Turkey Breast₇
(DETAILS)
10 lbs. 4 hrs.
12" x 20"
pans 3 hrs.
COOK
COOK
250⁰ F
1 hr.
Overnight
HOLD
170⁰ F 170⁰ F
160⁰ F 160⁰ F
160⁰ F 180⁰ F
160⁰ F 160⁰ F
160⁰ F 175⁰ F
INTERNAL
LOADING
3 per shelf
1 pan per shelf
14
VRH SERIES OVENSF-41207 (11-12)
ENTRÉE
TEMP.
TIME
TEMP.
TIME
Baked Rotini
60 min.
20 min.
Beef & Noodles
225⁰F
54 min.
160⁰F
20 min.
Breaded Chicken Pattie on Bun
225⁰F
60 min.
165⁰F
20 min.
Burrito
48 min.
20 min.
Cheesy Bread/Italian Dunker Sauce
200⁰F
54 min.
155⁰F
15 min.
Cheesy Chili
54 min.
15 min.
Chicken & Noodles
225⁰F
54 min.
160⁰F
20 min.
Chicken & Rice
54 min.
20 min.
Chicken Dippers
225⁰F
54 min.
160⁰F
20 min.
Chicken Fryz
48 min.
20 min.
Chicken Leg
225⁰F
60 min.
155⁰F
20 min.
Chicken Nuggets
60 min.
20 min.
Chik'n O's, Zesty
225⁰F
54 min.
160⁰F
20 min.
French Toast/Sausage Links
42 min.
15 min.
Grilled Cheese Sandwich
200⁰F
42 min.
155⁰F
15 min.
Grilled Chicken on Bun
60 min.
20 min.
Ham & Cheese English Muffin
54 min.
20 min.
Hamburger on Bun
250⁰F
60 min.
165⁰F
20 min.
Hot Dog on Bun
54 min.
20 min.
Italian Spaghetti
250⁰F
54 min.
160⁰F
20 min.
Macaroni & Cheese
48 min.
20 min.
Mexican Cheese Sauce
200⁰F
42 min.
155⁰F
20 min.
Mini Corndogs
54 min.
15 min.
Pancakes/Sausage Links
225⁰F
42 min.
160⁰F
15 min.
Pizza Dippers
54 min.
20 min.
Pizza, Cheese
200⁰F
42 min.
160⁰F
20 min.
Pizza, Pepperoni
54 min.
20 min.
Pizza, Sausage
200⁰F
54 min.
160⁰F
20 min.
Ravioli
60 min.
20 min.
Sausage Mini Bites
225⁰F
54 min.
160⁰F
15 min.
Steak Nuggets
60 min.
20 min.
Taco Boat
225⁰F
42 min.
160⁰F
20 min.
Tacos
42 min.
20 min.
Turkey & Noodles
225⁰F
54 min.
160⁰F
20 min.
Turkey Manhattan
54 min.
20 min.
RETHERMALIZATION GUIDE
OVEN
225⁰F
250⁰F
225⁰F
225⁰F
225⁰F
225⁰F
225⁰F
225⁰F
200⁰F
REHEAT
HOLD
160⁰F
160⁰F
160⁰F
160⁰F
160⁰F
160⁰F
160⁰F
165⁰F
160⁰F
MIN. HOLD
225⁰F
225⁰F
225⁰F
225⁰F
200⁰F
250⁰F
225⁰F
225⁰F
225⁰F
160⁰F
155⁰F
160⁰F
160⁰F
160⁰F
165⁰F
160⁰F
160⁰F
165⁰F
15
VRH SERIES OVENSF-41207 (11-12)
16
VRH SERIES OVENSF-41207 (11-12)
17
VRH SERIES OVENSF-41207 (11-12)
18
LOCKOUT / TAGOUT PROCEDURE
Always perform the Lockout / Tagout Procedure before
removing any sheet metal panels or attempting to service this
equipment.
The Lockout / Tagout Procedure is used to protect personnel working on an electrical
appliance. Before performing any type of maintenance or service on an electrically operated
appliance, follow these steps:
1. In electrical box, place unit’s circuit breaker into OFF position.
2. Place a lock or other device on electrical box cover to prevent someone from placing
circuit breaker ON.
3. Place a tag on electrical box cover to indicate that unit has been disconnected for
service and power should not be restored until tag is removed by maintenance
personnel.
4. Disconnec t uni t power cord from electrical outl et.
5. Place a tag on cord to indicate that unit has been disconnected for service and power
should not be restored until tag is removed by maintenance personnel.
SERVICE & PARTS INFORMATION
To obtain Service and Parts information concerning this model, contact the Vulcan Service
Department at the address listed on the front cover of this manual or refer to our website:
www.vulcanequipment.com for a complete listing of Authorized Service and Parts depots.
Customer Service1-800-814-2028
Technical Service 1-800-814-2028
Service Parts 1-800-814-2028
When calling for service, have the model number and serial number available.
VRH SERIES OVENSF-41207 (11-12)
19
TROUBLESHOOTING
SYMPTOMSP OSS IBL E CAUS ESREMEDY
Oven not c onnect ed t o
power sourc e
Connect oven to power
source
ON/OF F switc h not
ON
Pres s P ower ON/ OF F switc h
to ON
Oven is bel ow 150⁰F.
This is normal when unit is
col d. If unit i s above 150⁰F.,
Contac t A ut hori zed Service
Provider.
Defecti ve: connect i on,
wiring, fan, t herm ost at
Contac t A ut hori zed Service
Provider
Oven compartment IS heating
and Blower Motor IS NOT
operating with Power Switch
ON
Defecti ve connec t i on or
wiring t o m otor
Contac t A ut hori zed Service
Provider
Defec tive Cook ing
Temperature
Thermostat
Set C ooking Therm ostat to 250⁰F.,
wait several minutes and check
the rear of the oven for heating.
Both the Power Switch and
Cooking Temperature Indicator
Lights w ill be lit. If oven cavity
does not heat, Contact Authorized
Service Provider
Defec tive Holding
Temperature
Thermostat
Turn H olding Temperature knob to
250⁰F. and check for heat at rear
of oven cavity. Both the Power
Switch and Cook ing Temperature
I ndicator Lights w ill be lit. If the
oven cavity does not heat, C ontact
Authorized Service Provider.
Defecti ve High-Limit
Thermost at or Heat i ng
Element.
Contac t A ut hori zed Service
Provider
Inc orrect oven temper a tu re
Thermost at (s) require
calibration
Contac t A ut hori zed Service
Provider
Check ci rc ui t break er
Oven not operat ing
Indi cator Lights are lit but
Cooling Fan(s ) are NOT
operating
Oven c ompa r tment IS NOT
heating and Blower Motor IS
operating with Power Switch
ON
No power
VRH SERIES OVENSF-41207 (11-12)
20
SPECIFICATIONS
MODEL
NO.
PAN
QTY.
PAN SIZE
HEIGHT
WIDTH
DEPTH
SHIP
WEIGHT
VOLTS
WATTS
AMPS
VRH8
8 ea. 18" x 26"
42.5” 1080
mm
25.5" 650
mm
33” 839
mm
170# 78
kg.
208 2253 10.8
16 ea. 12"x20"x2½ 240 3000 12.5
VRH88
16 ea. 18" x 26"
79.5” 2020
mm
25.5” 650
mm
33” 839
mm
340 #
156
kg.
208 2253 10.8
32 ea. 12"x20"x2½ 240 3000 12.5
VRH SERIES OVENSF-41207 (11-12)
21
WIRING DIAGRAM
VRH8, VRH88
VRH SERIES OVENSF-41207 (11-12)
22
VRH SERIES OVENSF-41207 (11-12)
23
VRH SERIES OVENSF-41207 (11-12)
24
Loading...
+ hidden pages
You need points to download manuals.
1 point = 1 manual.
You can buy points or you can get point for every manual you upload.