User Manual
Please read the instructions carefully before use
The Vulcan Kratos is a Versatile Multi-color LED Par Luminaire utilizing 18 x 18W RGBAW+UV
LEDs.
It is equipped with 3 & 5 Pin XLR’s for use with DMX-512 and also features Powercon in &
through connectors.
1
1. Safety Introductions
Please read the instructions carefully which includes important
information about the installation, operation and maintenance.
WARNING
Pleas e keep this User Guide for future consulta tion. I f you sel l the unit to another user, be
sure th at they also receive this instruction bo oklet .
All fix tures are intact from the manufacturer , pleas e opera te follow up the user manual,
artif icial fault are not under guarantee repa ir.
Unpac k and check carefully that there is no trans porta tion da mage before using the unit.
The uni t is for indoor use only. Use only in a dry l ocati on.
Do inst all and operate by operator.
Use saf ety chain when fixes the unit. Don’t handl e the uni t by taki ng its head only, but
alway s by taking its base.
The uni t must be installed in a location with adequ ate ven tilat ion, at least 50cm from
adjac ent surfaces.
Be sure t hat no ventilation slots are blocked, ot herwi se the un it will be overheated.
Befor e operating, ensure that the voltage and f reque ncy of po wer supply match the
power r equirements of the unit.
It’s im portant to ground the yellow/gr een con ducto r to eart h in order to avoid
elect ric shock.
Maxim um ambient temperature TA : 40℃. Don’t ope rate it w here th e temperature is
highe r than this.
Don’t c onnect the device to any dimmer pack.
First r un, there will be smoke or smells, an d all dis appea ring a fe w minutes later.
Make su re there are no flammable materials clos e to the un it whil e operating,
as it is fi re hazard.
Look ov er power wires carefully, replace imme diate ly if the re is any damage.
Never r un on for a long time lest shortening lifesp an.
Avoid a ny inflammable liquids, water or metal o bject s enter ing the unit.
Once it h appen, cut off the mains power
immed iately.
Do not op erate in dirty and dusty environment, al so clea ning fi xtures regularly.
2
Do not al low children to operate the fixture.
Do not to uch any wire during operation as th ere mig ht be a haz ard of el ectric shock.
Avoid p ower wires together around other cable s.
Disco nnect mains power before fuse/lamp rep lacem ent or se rvicing.
Repla ce fuse only with the same type.
In the ev ent of serious operating proble m, stop u sing th e unit im mediately.
Never t urn on and off the unit time after time.
The hou sing, the lenses, or the ultraviolet fil ter mus t be repl aced if they are visibly
damag ed.
Do not op en the unit as there are no user serviceable p arts in side.
Never t ry to repair the unit by yourself. Repairs c arrie d out by un skilled people can
lead to d amage or malfunction. Please co ntact t he near est aut horized technical
assis tance center.
Disco nnect the mains power if the fixture is not us ed for a lo ng time .
Do use or iginal packing materials once transp ort it ag ain.
Do not lo ok directly at the LED light beam whi le the fi xture i s on.
For power supply, do not connect in series much more than 7 units, use
another mains supply for next 7 units.
Installation
The uni t should be mounted via its screw holes on the b racke t. Alwa ys ensure that the
unit is f irmly fixed to avoid vibration and slipp ing whi le oper ating. Always ensure that
the str ucture to which you are attaching the unit i s secur e and is ab le to support a
weigh t of 10 times of the unit’s weight. Als o alway s use a saf ety cab le that can hold
12 time s of the weight of the unit when instal ling th e fixtu re.
The equ ipment must be fixed by professionals. A nd it mus t be fixe d at a place where is
out of th e touch of people and has no one pass by or under it .
3
Technical Specifications
three k inds of operation mode: DMX Maste r & Slave .
sound c ontrol
POWER C ONSUMPTION:350W
DMX Cha nnel mode: 6/10CH
The bui lt-in program control light in the maste r and
slave m ode by voice control.
0~100 % smooth dimming function and effect of
each va riety of trobe
suita ble for disco, bar, mobile DJ etc.
Volta gue: AC 100~2 40V, 50/60H z
LEDs: LEDS:18 PCS*18W(6 in 1)
Net wei ght: 2.5kgs
Measu re: 278*271*123mm
How to Set the Fixture
1.The indicating light
2.Function display: display menu and
the selected function
3.Menu button
4.Microphone
5.DMX signal output
6.Power supply socket
7.DMX signal input
4
DMX Mode
Channel slection mode
Master/Slave mode
Performance mode
Menu
5
Backlight mode
show positive and negative direction
manual mode
Auto-test
Machine using time
DMX Mode
Selec t the Addr menu, press the ENTER key to confir m. Then u se the in itial address code
DOWN/ UP button to set this light (A001 ~ A51 2). Onc e you hav e set you r initial address
code, p ress ENTER to define and save. Not to m ake any c hange s, wait a m inute to
autom atically exit the menu and save. The main me nu, ple ase pre ss the MENU button
Channel selection model
Selec t the Chnd menu, press the ENTER key to d eterm ine. To u se the DO WN/UP button
to chan nel mode: 6Ch (6 Channel).10Ch (1 0 Chann els) mo de. Sel ect the desired channel
mode, p ress ENTER to determine and save. Not to mak e any cha nges, w ait a minute to
autom atically exit the menu and save. The main me nu, ple ase pre ss the MENU button
Master/Slave mode
Selec t the SLnd menu, press the ENTER key to confir m. To use t he DOWN /UP key set of
Maste r-Slave mode need: NAST(master.SL 1( Slave 1 ).SL 2( Slave 2).SL 3(Slave 3).
SL 4(Sl ave 4). Select the desired mode, press ENT ER to det ermin e and save. Not to
make an y changes, wait a minute to automaticall y exit th e menu an d save. The main
menu, p lease press the MENU button
Performance mode
Selec t the Shnd menu,press the ENTER key t o deter mine. To use DO WN/UP button to
perfo rmace mode:FADE(Gradient),SOUN (Soun d),Au to(Automatic),COLOR(Color)
mode, Select the desired mode,press ENTER to d eterm ine and s ave.Not to make any
chang es,wait a minute to automatically exit t he menu a nd save .The main menu,
pleas e press the MENU Button FADE(Gradient) SP 1-SP 8 8 f ades sp eed selection.use
DOWN/ UP button to select the gradient speed req uired .acco rding to ENTER,determine
and sav e.Not to make any changes,wait a mi nute an d autom atica lly exit the MENU
and sav e.The main menu.plase press the M ENU but ton Col or(Co lor)CO 1-CO 16 16
progr am mode,And also press Stro(Str obe) ha ve 0-25 5 to adju st the speed,use the
DOWN/ UP button to select the desired mod e.Pre ss ENTE R to dete rmine and ave.
NOT to ma ke any changes,wait a minute to automati cally e xit the m enu and save.
6
Backlight mode
Selec t the LED menu, press the ENTER key to determi ne. The n use the D OWN/UP button
to set th e backlight mode: ON (Open).OFF (Close ). Sele ct the de sired mode, press ENTER
to dete rmine and save. Not to make any changes, wai t a minut e to auto matically exit
the men u and save. The main menu, please press the ME NU butt on
White Balance
Selec t the BALA menu,Press the ENTER key to deter mine. To use th e DOWN/UP to display
mode: Red(Red),Gree(Green,Blue(BLu e),se lect th e desired mode,Press ENTER to
deter mine and save.Not to make any changes,Wa it a mome nt to aut omatically
exit th e menu and save.The main menu,Please pre ss the ME NU butt on Red(Red)
with 12 5-255 using the DOWN/UP button to bright ness. Press E NTER to define and
save. Not to make any changes,wait a minute to aut omati cally e xit the menu and
save. The main menu,Please press the MENU butt on Gree (Gree n) with 125-255
using t he DOWN/UP button to brightness .Pres s ENTER t o defin e and save.Not to
make an y changes,wait a minute to automa tical ly exit t he menu a nd save.
show positive and negative direction
Selec t the dISP menu, press the ENTER key to determ ine. To u se the DO WN/UP button to
displ ay mode: dISP (positive).DSIP (rever se). Se lect th e desired mode, press ENTER to
deter mine and save. Not to make any changes, wait a m inute t o autom atically exit
the men u and save. The main menu, please press the ME NU butt on
7
Auto-test
Selec t the Test menu, press the ENTER key to determ ine. Th e machi ne will start
autom atically detect color. Not to make any cha nges, w ait a min ute to automatically
exit th e menu and save. The main menu, please press t he MENU b utton
Fhrs
Selec t the Fhrs menu, press the ENTER key to determ ine. Yo u can see t he use of machine
time / h. N ot to make any changes, wait a minute t o autom atica lly exi t the menu and
save. T he main menu, please press the MENU button
temperature
Selec t the Tenp menu, press the ENTER key to determ ine. Yo u can see t he machine light
board t emperature / degree. Not to make any chang es, wai t a minut e to automatically
exit th e menu and save. The main menu, please press t he MENU b utton
8
DMX512 Connections
The DMX 512 is widely used in intelligent lighti ng cont rol, wi th a maximum of 512 channels.
COMM ON
DMX IN PUT
1
3
2
Termi nation reduces signal errors and avoid s signa l trans mission problems and
inter ference. lt is always advisable to conne ct a DMX te rmina l.
(Resi stance 120 ohm 1/4W)between pin2(DMX -)and p in3(D MX+) of the last fixture.
DMX +
DMX -
1
DMX OU TPUT
3
2
1
3
2
9
6CH Channel mode
1 CH 2 CH 3 CH 4 CH
Red Green Bl ue White
5 CH 6 CH
UV Anbe
10CH Channel mode
1 CH 2 CH 3 CH 4 CH 5 CH 6 CH 7 CH 8 CH
Red Green Bl ue White
UV Anbe
Dimmer
Strobe
0~7
No fun ction
8~99
Stro be(fr om
slow t o fast)
100~ 149
Stro be(fr om
fast t o slow)
150~ 199
Stro be effe ct 1
200~ 245
Stro be effe ct 2
246~ 255
Stro be,th e
fast est
stro be effe ct
9 CH 10 CH
color
walking
0~7
No
func tion
8~25 5
colo r
auto
control
Sound
0~7
No
func tion
8~19 9
colo r auto
spee d
200~ 255
Soun d
cont rol
Fixture Cleaning
The cle aning of internal must be carried out peri odica lly to op timize light output.
Clean ing frequency depends on the environme nt in whi ch the fi xture operates: damp,
smoky o r particularly dirty surrounding can c ause gr eater
accum ulation of dirt on the fixture’s optics.
Clean w ith soft cloth using normal glass c leani ng flui d.
Alway s dry the parts carefully.
Clean t he external optics at least every 20 days. C lean th e inter nal optics at least
every 30/60 days.
10
Loading...