VTech Telecommunications 80 9092 00 User Manual

User’s manual

TL80133
DECT 6.0 portable
wireless speaker

Congratulations

on your purchase of this AT&T product. Before using
this AT&T product, please read Important safety
information on pages 6-9 of this manual. Please
thoroughly read this user’s manual for all the feature
operations and troubleshooting information necessary
to install and operate your new AT&T product. You can
also visit our website at www.telephones.att.com or
call 1 [phone]. In Canada, dial 1 [phone]

Model number: TL80133

Type: DECT 6.0 portable wireless speaker

Serial number:

Purchase date:

Place of purchase:

Both the model and serial numbers of your AT&T product can be
found on the bottom of the speaker charger.

Save your sales receipt and original packaging in case it is
necessary to return your product for warranty service.

.

© 2013 Advanced American Telephones. All Rights Reserved. AT&T and
the AT&T logo are trademarks of AT&T Intellectual Property licensed to
Advanced American Telephones, San Antonio, TX 78219. Printed in China.

Parts checklist

Battery Pack :

2.4V Ni-MH

WARNING :DO NOT BURN OR

PUNCTURE BATTERIES.

THIS SIDE UP

Check to make sure the package includes the following items.
Save your sales receipt and original packaging in the event
warranty service is necessary.

User’s manual

TL80133
DECT 6.0 portable
wireless speaker

User's manual Wireless speaker

Power adapter for
speaker charger

Battery for wireless
speaker

Speaker charger

Battery
compartment
cover

Getting started

Quick reference guide

CHARGE light

FLASH

VOL-

MUTE

VOL

+

1

Getting started

Installation

You must install and
charge the battery before
using the speaker.

For customer service or product information, visit our website at

STOP!

See page 4 for
easy instructions.

www.telephones.att.com or call 1 [phone].

In Canada, dial 1 (866) 2 88-4268.

Avoid placing the telephone base too close to:

• Communication devices such as television sets, VCRs or other
cordless telephones.

• Excessive heat sources.

• Noise sources such as a window with traffic outside, motors,
microwave ovens, refrigerators or fluorescent lighting.

• Excessive dust sources such as a workshop or garage.

• Excessive moisture.

• Extremely low temperature.

• Mechanical vibration or shock such as on top of a washing
machine or work bench.

2

Getting started

Charger installation

Install the speaker charger as shown below.

Plug the large end of the
charger power adapter into a
power outlet not controlled by
a wall switch.

Route the power adapter cord
through this slot.

Plug the small end of the
charger power adapter into
the power adapter jack on the
back of the charger.

IMPORTANT INFORMATION

• Use only the power adapter provided with this product. To obtain aUse only the power adapter provided with this product. To obtain a

replacement, visit our website at www.telephones.att.com or
call 1 [phone]. In Canada, dial 1 [phone].

• The power adapter is intended to be correctly oriented in a vertical orThe power adapter is intended to be correctly oriented in a vertical or
floor mount position. The prongs are not designed to hold the plug in
place if it is plugged into a ceiling, under-the-table or cabinet outlet.

3

Getting started

Battery Pack :

2.4V Ni-MH

WARNING :DO NOT BURN OR

PUNCTURE BATTERIES.

THIS SIDE UP

Battery Pack :

2.4V Ni-MH

WARNING :DO NOT BURN OR

PUNCTURE BATTERIES.

THIS SIDE UP

Battery Pack :

2.4V Ni-MH

WARNING :DO NOT BURN OR

PUNCTURE BATTERIES.

THIS SIDE UP

Battery installation and charging

Install the battery as shown below.

Plug the battery connector

1. 2.
securely into the socket
inside the speaker battery
compartment.

Insert the supplied batteryInsert the supplied battery

with the label THIS SIDE UP
facing up as indicated.

CHARGE light
turns red

3. Insert the tab on the
bottom of the battery
compartment cover into
the battery compartment,
then press down gently

4. Charge the speaker byCharge the speaker by
placing it face upward in
the charger. The CHARGE
light on the speaker turns
red during charging.

on the cover until it snaps
into place.

To replace the battery, push the tab and lift the
battery compartment cover up and off.
Lift out the old battery and disconnect it from
the speaker. Follow the instructions above to
install and charge the new battery.

4

Getting started

Battery installation and charging

IMPORTANT INFORMATION

• Use only the supplied rechargeable battery or replacement batteryUse only the supplied rechargeable battery or replacement battery
(model BT185742/BT285742). To order, visit our website at

www.telephones.att.com or call 1 [phone].

In Canada, dial 1 [phone].

• If you do not use the speaker for a long time, disconnect and removeIf you do not use the speaker for a long time, disconnect and remove
the battery to prevent possible leakage.

Once you have installed the battery, the CHARGE light on the
speaker indicates the battery status (see the table below).
If necessary, place the speaker in the charger to charge the
battery. For optimal performance, keep the speaker in the charger
when not in use. The battery is fully charged after 11 hours of
continuous charging. See Technical specifications on page 20 for
battery operating times.

CHARGE light Battery status

Red: Flashes every 10 seconds. Battery has very little charge and

Red: Steadily on. Battery is charging.

Green: Steadily on. Battery is fully charged

notes:

If you are on a call in low battery mode, you hear a low battery alert tone

•
every 60 seconds.

If the battery is not properly installed or no battery is installed in the

•
speaker, when you place it in the charger, the CHARGE light is off. Follow the
instructions on page 4 to install the battery.

needs charging.

(in the charger).

5