VTech Telecommunications 80 0144 01, 80 0144 00 User Manual

User’s manual

LINKED

Battery Pack / Bloc-piles :

BT183342/BT283342 (2.4V

WARNING / AVERTISSEME

DO NOT BURN OR PUNCT

NE PAS INCINÉRER OU P

Made in China / Fabriqué

THIS SIDE UP / CE

DM223/DM223-2

Safe & Sound Digital Audio Monitor

Congratulations

on purchasing your new VTech product. Before using this product, please read Important safety instructions.

For support, shopping, and everything new at VTech, visit our website at

www.vtechphones.com.

Visit www.vtechphones.com.

Registration

Product news

Learn about the latest VTech products.

What’s in the box

1 set for DM223; 2 sets for DM223-2

Install the battery

The parent unit runs on rechargeable battery or AC power. To continuously monitor your baby, make sure you use both battery and AC power at the same time. With the battery alone, the parent unit can cordlessly run for a short time only.

NOTES

Use only the batter y supplied with this pro duct.

•

If the parent unit will not be used for a long time,

•

disconnect and remove the battery to prevent possible leakage.

Without AC power charging, the battery gradually

•

discharges, even when the parent unit is switched off.

Install the battery as shown below.

THIS SIDE UP

Made in China / Fabriqué en chine CR0920 NE PAS INCINÉRER OU PERCER LES PILES. DO NOT BURN OR PUNCTURE BATTERIES. WARNING / AVERTISSEMENT : BT183342/BT283342 (2.4V 400mAh Ni-MH) Battery Pack / Bloc-piles :

THIS SIDE UP / CE CÔTÉ VERS LE HAUT

NOTE

Make sure the suppli ed rechargeable batte ry with

•

the label THIS SIDE UP facing up.

Replace the battery

To replace the battery, unplug the battery connector from the socket, and then pull the battery out of the battery compartment. Follow the steps above to install the battery.

Connect and charge the battery

NOTES

Use only the parent unit power adapter or the baby

•

unit power adapter supplied with this product. Make sure the elect rical outlets are not con trolled

•

by wall switches. The parent unit power adapter and baby unit power

•

adapter are intended to be correctly oriented in a vertical or floor mount position. The prongs are not designed to hold the plug in place if it is plugged into a ceiling, under-the-table or cabinet outlet.

•

Make sure the parent unit, the baby unit and the power adapter cord are out of reach of children.

Connect the baby monitor

Charge the parent unit battery

Once you have connected the parent unit or

installed its battery, The battery icon indicates the battery status (see the following table).

NOTES

The parent unit bat tery is fully charged after 11

•

hours of continuous charging.

It takes longer to charge the battery when the

•

parent unit is turned o n. To shorten the charging time, turn the parent uni t off while charging.

The standby time var ies depending on the

•

sensitivit y level you set, your actual use and th e age of the batter y.

Battery indicators

The battery icon is off.

LOW BATTERY

and

ﬂash on the screen.

flashes.

The battery icon becomes solid

light

The

it powers on automatically.

Battery status

No battery is installed. The parent unit can be used only when it is connected to AC power.

The battery has very little charge and may be used for only a short time.

The battery is fully charged.

Action

Install the parent unit battery. Charge without interruption (at least 30 minutes).

Charge

without interruption (about 30 minutes).

To keep the battery charged, connect it to AC power when not in use.

Before use

NOTE

This baby monitor is inte nded as an aid. It is not a

•

substitute for prop er adult supervision, and s hould not be used as such.

You may test the baby monitor before initial use, and at regular times thereafter.

Place the parent unit and the baby unit in he same room to test the product.

Test your audio monitor

Speak towards the micropho ne of the baby

•

unit. You will hear the sound at the parent unit, and see the visual sound indicato rs light up.

TIP

Increase the spea ker volume of the parent unit if

•

you cannot hear the soun ds transmitted from the baby unit.

NOTES

•

Make sure the baby unit is at l east 1 meter (3 feet) away from the parent unit .

•

If no connection c an be established, the paren t unit displays NOT LINKED and

Positioning the baby monitor

CAUTION

Keep the baby unit out of the rea ch of the baby.

•

Never place or mount the b aby unit inside the baby’s crib or playpen.

•

Do not expose the baby uni t to extreme heat or direct sunlight.

LINKED

flashes.

Place the baby unit at least 1 meter / 3 feet

1. away from your baby.

At least 1 meter

(3 feet)

2. Place the parent unit at lea st 1 meter /

3 feet away from the baby unit.

At least 1 meter (3 feet)

NOTE

If you experience audio fe edback on either the

•

parent unit or baby unit , move the parent unit further away until the re is no more audio feedback;

VOL. on the parent unit to lower t he

or press audio feedback sound.

Operating range

The operating range of the baby monitor is up to 300 meters (1,000 feet) outdoors or 50 meters (160 feet) indoors. The actual operating range may vary depending on the environmental conditions, and other interferences such as walls, doors, and other obstructions.

Overview

Baby unit overview

a b c

2 3

9 10

VOL.

Press to decrease the speaker

•

volume.

Microphone

NIGHT LIGHT

Press to turn the night light on or off.•

Night light

On when night light is turned on.•

POWER light

On when the baby unit is turned on.•

VOL.

Press to increase the speaker

•

volume.

POWER

Press and hold to power on or off.•

PAGE

Press to start or stop paging parent

•

unit.

Power jack

Speaker

Parent unit overview

a b c

f g

Microphone

VOL.

Press to decrease the speaker

•

volume. While in a menu, press to scroll down.

•

Speaker

MENU/

Press to enter the menu while idle.

•

While in a menu, press to return to the

•

previous screen. Press to return to idle screen.

•

Visual sound indicator

The visual sound indicator has two functions. One is to show the sound level detected by the baby unit. The other one is to show the volume level during speaker volume setting.

Sound level detected by the baby unit

•

lights indicate a moderate sound level detected by the baby unit.

•

lights indicate a higher sound level detected by the baby unit (e.g. baby crying loudly).

Speaker volume level

•

lights indicate Level 1 to Level 3 of the speaker volume setting.

•

lights indicate Level 4 to Level 5 of the speaker volume setting.

LCD panel

One to three green

Additional red

One to three green

Additional red

Battery level indicator Light on when the battery is being

•

charged. Light flashes when the battery is low

•

and needs charging.

Light off when no battery is installed.

•

VOL.

Press to increase the speaker volume.

•

While in a menu, press to scroll up.

•

SELECT

While in a menu, press to choose an

•

item, or save a setting.

(On/off)

•

Press and hold to power on or off.

•

While in a menu, press to return to idle screen.

TALK

Press and hold to talk to the baby unit;

•

release to stop talking. While in a menu, press to return to

•

idle screen.

Power jack

Belt clip

Battery compartment cover

Parent unit display icons

Connection status

displays when strong signal

•

strength is detected between the baby unit and the parent unit.

displays when moderate signal

•

strength is detected between the baby unit and the parent unit.

displays when the weak signal

•

strength is detected between the baby unit and the parent unit.

flashes when the link between the

•

baby unit and the parent unit is lost.

Night light auto-on

On when the night light auto-on

•

feature is turned on.

Sound alert

Displays when the sound alert of the

•

parent unit is turned on. Flashes when there are loud sounds

•

detected from the baby unit and the parent unit is in mute.

Vibration alert

Displays when the vibration alert of

•

the parent unit is turned on. Flashes when there are loud sounds

•

detected from the baby unit.

Mute

Displays when the volume is turned

•

off.

Battery status

•

the battery is charging.

displays solid when the battery is

•

fully charged.

flashes when the battery is

•

charged with AC adaptor, or charging failure.

flashes when the battery is in low

•

level and needs charging. No battery icon displays when there

•

is no battery installed.

animates when

Parent unit display screen messages

The battery charging

CHECK

performance is abnormal, the

BATT

light is off and the on the screen.

The link between the parent unit

LINKED

and the baby unit is established. The parent unit uses only the

LOW

rechargeable battery pack and it

BATTERY

needs to be recharged.

The link between the parent

NOT

unit and the baby unit is lost

LINKE D

continuously for over 10 seconds.

All idle parent units are being

PAGING

paged by the baby unit.

Your selection has been saved.

SAVED

The parent unit is out of range of

SEARCHING

the baby unit, or the baby unit is out of power.

The parent unit is talking to the

TALK

baby unit.

The other parent unit is talking to

TALKBACK

the baby unit.

Using the baby monitor

Power on or off the baby unit

Press and hold

•

icon flashes

baby unit. The Press and hold POWER again to power off

•

the baby unit. The

Power on or off the parent unit

Press and hold

•

unit. The screen turns on. Press and hold

•

parent unit. The screen turns off.

NOTE

The parent unit powers o n automatically once

•

it is connected to AC powe r or battery installed. The baby unit also power s on automatically once connected to AC power.

Adjust the speaker volum e for baby unit

•

Press VOL. any time.

Adjust the speaker volume fo r parent unit

You can adjust the speaker volume from VOLUME 1 to VOLUME 5, or turn it off. The speaker volume is preset to VOLUME 3.

•

Press VOL.

unit is not in use. When the speaker volume is set to off, the screen displays

POWER to power on the

power light turns on.

power light turns off.

to power on the parent

again to power off the

or VOL. on the baby unit at

or VOL. when the parent

Adjust the sound sensitivit y of the baby unit

You can choose to hear sounds from the baby unit all the time, or to hear sounds that exceed a certain level. You can use the parent unit to adjust the microphone sensitivity of your baby unit. The higher the sensitivity level, the more sensitive the baby unit is in detecting sounds for transmitting to the parent unit. The sound sensitivity is preset to LEVEL 5.

Sound sensitivity table for reference

Display Sensitivity Description

Level 5

Level 4

Level 3

Level 2

Level 1

Press MENU when the parent unit is not in use.

Press SELECT.

2. Press VOL.

3. sensitivity level.

Press SELECT to confirm your selection.

4. The screen displays SAVED and you hear a confirmation tone.

High sensitivity level

High

The parent unit speaker is

sensitivity

constantly on, and you will hear all sounds (including background noises) from your baby’s room.

Medium high sensitivity level

The parent unit speaker turns on for soft babbling and louder sounds from your baby. It remains quiet when your baby sleeps soundly.

Medium sensitivity level

The parent unit speaker turns on for loud babbling and louder sounds from your baby. It remains quiet when your baby makes soft sounds.

Medium low sensitivity level

The parent unit speaker turns on for crying and louder sounds from your baby. It remains quiet when your baby makes soft sounds.

Low sensitivity level

The parent unit speaker turns on for loud crying or screeching sounds from your baby. It remains quiet

Low

when your baby makes

sensitivity

soft sounds.

or VOL. to choose the

NOTE

•

To enter the sensitivity menu o f the parent unit, the baby unit must be tur ned on.

Sound alert

Sound alert feature works only when the parent unit is in mute.

If you turn on the sound alert, the parent unit beeps when the baby unit detects sounds which light up four sound level indicators on the parent unit.

When the sound alert of the parent unit is turned

displays. The sound alert is preset to OFF.

on,

Press MENU when the parent unit is not in

1. use.

Press VOL.

•

Vibration alert

You can turn on the vibration alert so that the parent unit vibrates when the baby unit detects sounds which light up four sound level indicators on the parent unit.

When the vibration alert of the parent unit is turned on, OFF.

•

or VOL. to choose

SOUND ALERT, then press SELECT.

Press VOL.

or VOL. to choos e ON or

OFF. Press SELECT to confirm your selection.

The screen displays SAVED and you hear a confirmation tone.

NOTE

The sound alert se tting on each parent unit is independent.

displays. The vibration alert is preset to

Press MENU when the parent unit is not in use.

Press VOL.

or VOL. to choose

VIBE ALERT, then press SELECT. Press VOL.

or VOL. to choos e ON or

OFF. Press SELECT to confirm your selection.

The screen displays SAVED and you hear a confirmation tone.

NOTES

Each time you set the vib ration alert to ON, the parent unit vibr ates briefly after you press

SELECT.

The vibration aler t setting on each parent un it is independent.

Night light auto-on

You can turn on or off the night light by pressing the NIGHT LIGHT button manually on the baby unit. You can also use the parent unit to set the night light on the baby unit to automatically turn on whenever sounds are detected from the baby unit.

When the night light auto-on setting is set to YES,

displays. The default setting is preset to NO.

Press MENU when the parent unit is not in

1. use.

Press VOL.

•

Language

You can select a language (English, French or Spanish) to be used in all screen displays. The language is preset to English.

•

or VOL. to choose

NIGHTLIGHT, then press SELECT.

Press SELECT to choose AU TO ON. Press VOL.

or VOL. to choos e YES or

NO. Press SELECT to confirm your selection.

The screen displays SAVED and you hear a confirmation tone.

NOTES

To enter the night light menu of the par ent unit, the baby unit must be turn ed on.

If the night light on the b aby unit is already on, the night light will go off immediately when you change the night light auto-on setting from YES to NO.

If the night light on the b aby unit is already on and the night light auto-on setting is YES, the night light on the baby unit wil l go off immediately after you press NIGHT LIGHT and the night light auto-on feature will be come inactive for 5 minutes.

For night light triggered by baby’s sound or turned on manually at the baby unit, i t will automatically turn off after 15 minutes of silence.

Press MENU when the parent unit is not in use.

Press VOL.

or VOL. to choose

LANGUAGE, then press SELECT.

or VOL. to choos e

Press VOL. ENGLISH, FRANCAIS or ESPANOL.

Press SELECT to confirm your selection. The screen displays SAVED and you hear a confirmation tone.

NOTE

The language setti ng on each parent unit is independent.

Set default

Use this feature to restore to the default settings. Restoring the default settings on one parent unit will also reset the shared settings for sensitivity and night light auto-on feature of the other parent unit.

Press MENU when the parent unit is not in

1. use.

Press VOL.

-OR-

When you choose NO, press SELECT to

Talk to the baby unit

You can broadcast messages from a parent unit to the baby unit and the other parent unit. If you have two parent units, you can use both of them at the same time to talk to the baby unit.

•

Find/page the pa rent unit

Use this feature to find misplaced parent units.

•

number only signifies that the Industry Canada technical specifications were met. This product meets the applicable Industry Canada technical specifications.

RF radiation exposure statement

The baby unit complies with FCC RF radiation exposure limits set forth for an uncontrolled environment. The baby unit should be installed and operated with a minimum distance of 8 in (20 cm) between the baby unit other accessories may not ensure compliance with FCC RF exposure guidelines. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. This equipment complies also with Industry Canada RSS-102 with respect to Canada’s Health Code 6 for Exposure of Humans to RF Fields.

California Energy Commission battery charging testing mode

This baby monitor meets the California Energy Commission (CEC) regulations for energy consumption. Your baby monitor is set up to comply with the energyconserving standards right out of the box.

Follow the instructions to install and charge the battery. The activated while charging.

Even if the parent unit is paired to baby units, the

battery charging testing mode

powered off and charging.

or VOL. to choose

SET DEFAULT, then press SELECT.

or VOL. to choos e YES or

Press VOL. NO.

When you choose YES, press SELECT to confirm your selection. The screen displays SAVED and you hear a confirmation tone.

confirm your selection. The screen displays the previous menu.

Press and hold

TALK on the side of the

parent unit. The screen displays TALK when the voice connection to the baby unit is made. Speak towards the MIC on the parent unit. Your voice is broadcast to the baby unit and the other parent unit.

NOTE

When a parent unit is ta lking to the baby unit, it is also broadcas t to the other parent unit. However, sounds from the baby uni t cannot be transmitted to the parent units at t he moment.

Press PAGE on the baby unit. All idle parent units ring and display PAGI NG.

To end paging, press any key on the parent unit, or press PAGE on the baby unit.

NOTES

Paging rings all paren t units even if the speaker volume of parent unit i s set to VOLUME OFF.

The baby unit cannot pa ge any parent unit that is turned off, out of range o r talking to the baby unit.

and all persons’ body. Use of

CEC battery charging testing mode is

is activated while it is

CEC

For cETL compliance only

Mesures de sécurité importantes

Lorsque vous utilisez votre appareil, vous devriez toujours suivre certaines mesures de précaution de base afin de réduire les risques d’incendie, d’électrocution et de blessures corporelles, dont ceux qui suivent:

Observez toutes les instructions et mises en garde

1. inscrites sur l’appareil.

L’installation par un adulte est requise.

2. Ce produit a été conçu pour être un dispositif

3. d’appoint seulement. Il n’est pas le remplacement d’une supervision responsable et adéquate par un adulte et ne devrait pas être utilisé comme telle.

Ce produit n’est pas conçu pour être utilisé en tant

4. que moniteur médical.

N’utilisez pas cet appareil près de l’eau ni de toute

5. autre source d’humidité, par exemple, près d’une baignoire, cuve à lessive, évier de cuisine, dans un sous-sol humide ni près d’une piscine, dans un soussol humide ou une douche.

General product care

To keep this product working well and looking good, follow these guidelines:

•

Avoid putting it near heating appliances and devices that generate electrical noise (for example, motors or fluorescent lamps).

•

DO NOT expose it to direct sunlight or moisture.

•

Avoid dropping the product or treating it roughly.

•

Clean with a soft cloth.

•

DO NOT immerse the parent unit and the baby unit in water and do not clean them under the tap.

•

DO NOT use cleaning spray or liquid cleaners.

•

Make sure the baby unit and parent unit are dry before you connect them to the mains again.

Storage

When you are not going to use the baby monitor for some time, remove the rechargeable battery from the parent unit. Store the parent unit, the baby unit and the adapters in a cool and dry place.

MISE EN GARDE: Il peut y avoir un risque

6. d’explosion si vous utilisez le mauvais type de piles pour l’unité du parent. N’utilisez que le bloc-piles rechargeable inclus ou le bloc-piles de

(BT166342/BT266342). N’incinérez pas

rechange les piles. Celles-ci risqueraient d’exploser. Jetez les piles usées selon les renseignements suivant

le sceau du RBRC

N’utilisez que les adaptateurs inclus avec ce

7. produit. L’utilisation d’un adaptateur dont la polarité ou la tension serait inadéquate risque d’endommager sérieusement le produit et mettre votre sécurité en péril. Adaptateur de l’unité du bébé: Entrée 100-120V CA 150 mA 60 Hz; Adaptateur de l’unité du parent: Entrée 100-120V CA 150 mA 60 Hz;

Lorsqu’ils sont branchés dans une prise de

8. courant, les adaptateurs secteur ont été conçus pour être orientés correctement, soit à la verticale ou au plancher. Les broches n’ont pas été conçues pour supporter le poids du bloc d’alimentation et le maintenir en place si celuici est branché dans une prise au plafond, sous une table ou dans un meuble.

Pour les PRODUITS À BRANCHER À UNE

9. PRISE DE COURANT, la prise de courant doit être installée près du produit, afin d’assurer une accessibilité sécuritaire à la prise de courant.

Débranchez ce produit de la prise de courant

10. avant de procéder au nettoyage. N’utilisez pas de nettoyants en aérosols. Utilisez un chiffon humide pour le nettoyer.

Débranchez les cordons d’alimentation avant de

11. remplacer le bloc-piles.

Ne coupez pas les cordons d’alimentation pour

12. remplacer les fiches, car ceci peut présenter un danger potentiel.

Ne laissez aucun objet reposer ni appuyer sur le

13. cordon d’alimentation. N’installez pas cet appareil dans un endroit où l’on risque d’écraser le cordon d’alimentation ou de le piétiner.

Ne faites fonctionner cet appareil qu’avec le type

14. d’alimentation indiqué sur l’étiquette. Si vous ne connaissez pas le type d’alimentation que vous possédez à votre domicile, consultez votre marchand ou votre compagnie locale d’électricité.

Ne surchargez pas les prises de courant murales

15. ni les rallonges électriques.

Ne placez pas cet appareil sur un chariot, meuble,

16. trépied, support de montage ni table chancelants.

Les trous et ouvertures du boîtier, situés à l’arrière

17. de l’appareil ou sous celui-ci, servent à aérer l’appareil. Pour l’empêcher de surchauffer, ne bloquez sous aucun prétexte ces ouvertures et

Sortie : 6 V CC 400 mA.

Frequently asked questions

Below are the questions most frequently asked about the baby monitor. If you cannot find the answer to your question, visit our website at www.vtechphones.com or call 1 (800) 595-9511 for customer service.

Why does the baby monitor not respond normally?

Why doesn’t the screen of the parent unit go on when I switch on the unit?

Why doesn’t the POWER light of the baby unit go on when I switch on the unit?

Why does the baby monitor produce a high-pitched noise?

Why does the parent unit react too quickly to other sounds?

18.

19.

20.

21.

22.

23.

24.

Mises en garde

Try the following (in the order listed) for common cure:

1. Disconnect the power to the baby unit and the parent units.

2. Remove the batteries in the parent units. Then, install the batteries again.

3. Wait a few minutes before connecting power back to the baby units and the parent unit.

4. Turn on the baby unit and the parent units.

5. Wait for the parent units to synchronize with the baby unit. Allow up to one minute for this to take place.

Perhaps the rechargeable battery of the parent unit is empty and the parent unit is not connected to the power. Insert the appliance plug into the parent unit and put the adapter in a wall socket.

Perhaps the baby unit is not connected to the power. Connect the baby unit to the power.

The units may be too close to each other. Make sure the parent unit and the baby unit are at least 1 meter/3 feet away from each other.

The baby unit also detects other sounds than those of your baby. Adjust the sensitivity level to a lower level or adjust the speaker volume on the parent unit.

n’empêchez pas l’aération adéquate de l’appareil en le plaçant sur un lit, divan, tapis ou toute autre surface similaire. De même, ne le positionnez pas à proximité ni au-dessus d’une source de chaleur ou d’un calorifère. De plus, ne placez pas l’appareil dans un endroit avant de vous assurer qu’il y ait une bonne circulation d’air.

N’enfoncez jamais d’objets à travers les ouvertures de cet appareil, car ils pourraient entrer en contact avec des points de tension dangereux ou causer des courts-circuits qui peuvent dégénérer en incendies ou en risques d’électrocution. Ne renversez jamais de liquide dans ce produit.

Afin de réduire les risques d’électrocution, ne démontez pas cet appareil, mais apportez-le dans un centre de service autorisé. L’ouverture du boîtier ou le retrait de toutes pièces que contient cet appareil, à l’exception de l’accès autorisé à certaines portes ou ouvertures, risque de vous exposer à des points de tension dangereux ou d’autres dangers. Un remontage incorrect peut par la suite présenter des risques d’électrocution.

Vous devriez tester la réception chaque fois que vous mettez l’appareil en fonction.

Examinez les composantes afin de vérifier si celles-ci ne sont pas endommagées.

Soyez avisé de la perte de la confidentialité lorsque vous utilisez les ondes publiques. Les conversations peuvent être entendues par d’autres moniteurs de bébé, des téléphones sans fil, des scanneurs, etc.

Les enfants devraient être supervisés afin de vous assurer qu’ils ne jouent pas avec l’appareil.

Le produit n’est pas conçu pour être utilisé par des personnes (incluant des enfants) aux capacités physiques, sensorielles ou mentales réduites ou qui manquent d’expérience et de connaissances, à moins qu’on leur ait donné suffisamment de supervision ou d’instructions relativement à l’utilisation de l’appareil par une personne responsable de leur sécurité.

CONSERVEZ CES INSTRUCTIONS

Utilisez et entreposez le produit à une température

entre 0˚ C (32˚F) et 40˚C (104˚ F).

N’exposez pas cet appareil à des froids ou des chaleurs extrêmes, ainsi qu’à la lumière directe du soleil. Ne l’installez pas près d’une source de chauffage.

Le bloc-piles ne doit pas être exposé à la chaleur excessive telle que la lumière du soleil ou au feu.

Why don’t I hear a sound/ Why can’t I hear my baby cry?

Why does the parent unit beep?

Why can’t I establish a connection? Why is the connection lost every now and then? Why are there sound interruptions?

Important safety instructions

When using your equipment, basic safety precautions should always be followed to reduce the risk of fire, electric shock and injury, including the following:

Stimulateurs cardiaques implantés dans l’organisme

Les simulateurs cardiaques (ne s’applique qu’aux dispositifs numériques sans fil):

L’organisme ‘Wireless Technology Research, LLC (WTR)’, une firme de recherche indépendante, a mené une évaluation pluridisciplinaire des interférences entre les téléphones sans fil portatifs et les stimulateurs cardiaques implantés dans l’organisme. Appuyée par l’Administration des aliments et drogues (FDA) des États-Unis, la firme WTR recommande aux médecins:

Avis aux détenteurs de stimulateurs cardiaques

•

L’étude effectuée par l’organisme WRS n’a pas identifié de risque pour les détenteurs de simulateurs cardiaques causés par les gens qui utilisent dispositifs sans fil à proximité de ceux-ci.

Champs électromagnétiques (EMF)

Ce produit de VTech est conforme à toutes les normes se rapportant aux champs électromagnétiques (EMF) standard. Si vous le manipulez correctement en suivant les instructions de ce guide, son utilisation sera sécuritaire pendant de nombreuses années, selon les meilleures évidences scientifiques dont nous disposons aujourd’hui.

The volume of the parent unit may have set too low. Press

to increase the volume

VOL.

level. You may have set a low sound

sensitivity level. See Adjust the

sound sensitivity of the baby unit to change the setting.

If the parent unit is in mute and the sound alert feature is on, there is sound detected from the baby unit.

The baby units may be out of range. Move the parent unit closer to the baby units (but not less than 3 feet).

If the parent unit is powered by the provided battery, it may not have enough charge for the parent unit to perform normally. Charge the battery in the parent unit for up to 11 hours.

The baby units may be out of range. Move the parent unit closer to the baby units (but not less than 3 feet).

Other electronic products may cause interference with your baby monitor. Try installing your baby monitor as far away from these electronic devices as possible.

Follow all warnings and instructions marked on the product. Adult setup is required. This product is intended as an aid. It is not a substitute for responsible and proper adult supervision and should not be used as such. This product is not intended for use as a medical monitor. Do not use this product near water. For example, do not use it next to a bath tub, wash bowl, kitchen sink, laundry tub or swimming pool, or in a wet basement or shower.

CAUTION: Use only the batteries indicated in this manual. There may be a risk of explosion

Assurez-vous que le moniteur et le cordon de l’adaptateur sont toujours hors de portée des enfants, à au moins 1 mètre (3 pieds) de l’enfant ou du berceau, pour éviter tout risque de strangulation.

Ne jamais placer le moniteur à l’intérieur du berceau ou du parc de bébé. Ne jamais couvrir le moniteur ou l’unité (s) portative avec un article tel une serviette ou une couverture.

D’autres équipements électroniques peuvent produire des interférences sur votre moniteur vidéo et audio. Tentez d’installer votre moniteur vidéo ou audio à l’écart des appareils électroniques tels que des routeurs sans fil, radios, téléphones cellulaires, interphones, moniteurs, téléphones, ordinateurs personnels, électroménagers et téléphones sans fil.

Vous devriez maintenir les dispositifs sans fil à au moins six pouces du simulateur cardiaque.

Ils ne doivent PAS placer le téléphone sans fil directement sur le stimulateur cardiaque, tel que dans une poche de chemise, lorsque celui-ci est en marche.

if a wrong type of battery is used for the parent unit. Use only the supplied rechargeable battery or replacement battery pack (BT166342/ BT266342) for the parent unit. Do not dispose of batteries in a fire. They may explode. Dispose of used battery according to the information in The RBRC

7. Use only the adapters included with this product. Incorrect adapter polarity or voltage can seriously damage the product. Baby unit power adapter: I

150mA 60Hz; Output: 6V DC 400mA;

Parent unit power adapter:

AC 150mA 60Hz; Output: 6V DC 400mA

8. The power adapters are intended to be correctly oriented in a vertical or floor mount position. The prongs are not designed to hold the plug in place if it is plugged into a ceiling, under-the-table or cabinet outlet. For pluggable equipment, the socket-outlet

9. shall be installed near the equipment and shall be easily accessible.

10.Unplug this product from the wall outlet before cleaning. Do not use liquid or aerosol cleaners. Use a damp cloth for cleaning.

11.Unplug the power cords before replacing batteries.

12.Do not cut off the power adapters to replace them with other plugs, as this causes a hazardous situation.

13.Do not allow anything to rest on the power cords. Do not install this product where the cords may be walked on or crimped.

14.This product should be operated only from the type of power source indicated on the marking label. If you are not sure of the type of power supply in your home, consult your dealer or local power company.

15.Do not overload wall outlets or use an extension cord.

16.Do not place this product on an unstable table, shelf, stand or other unstable surfaces.

17.This product should not be placed in any area where proper ventilation is not provided. Slots and openings in the back or bottom of this product are provided for ventilation. To protect them from overheating, these openings must not be blocked by placing the product on a soft surface such as a bed, sofa or rug. This product should never be placed near or over a radiator or heat register.

18.Never push objects of any kind into this product through the slots because they may touch dangerous voltage points or create a short circuit. Never spill liquid of any kind on the product.

seal.

nput 100-120V AC

Input 100-120V

Limited warranty

What does this limited warranty cover?

The manufacturer of this VTech Product warrants to the holder of a valid proof of purchase (“Consumer” or “you”) that the Product and all accessories provided in the sales package (“Product”) are free from defects in material and workmanship, pursuant to the following terms and conditions, when installed and used normally and in accordance with the Product operating instructions. This limited warranty extends only to the Consumer for Products purchased and used in the United States of America and Canada.

What will VTech do if the Product is not free from defects in materials and workmanship during the limited warranty period (“Materially Defective Product”)?

During the limited warranty period, VTech’s authorized service representative will repair or replace at VTech’s option, without charge, a Materially Defective Product. If we repair the Product, we may use new or refurbished replacement parts. If we choose to replace the Product, we may replace it with a new or refurbished Product of the same or similar design. We will retain defective parts, modules, or equipment. Repair or replacement of the Product, at VTech’s option, is your exclusive remedy. VTech will return the repaired or replacement Products to you in working condition. You should expect the repair or replacement to take approximately 30 days.

How long is the limited warranty period?

The limited warranty period for the Product extends for ONE (1) YEAR from the date of purchase. If VTech repairs or replaces a Materially Defective Product under the terms of this limited warranty, this limited warranty also applies to the repaired or replacement Product for a period of either (a) 90 days from the date the repaired or replacement Product is shipped to you or (b) the time remaining on the original one-year warranty; whichever is longer.

What is not covered by this limited warranty?

This limited warranty does not cover:

Product that has been subjected to misuse, accident, shipping or other physical damage, improper installation, abnormal operation or handling, neglect, inundation, fire, water or other liquid intrusion; or

Product that has been damaged due to repair, alteration or modification by anyone other than an authorized service representative of VTech; or

Product to the extent that the problem experienced is caused by signal conditions, network reliability, or cable or antenna systems; or Product to the extent that the problem is caused by

4. use with non-VTech accessories; or Product whose warranty/quality stickers, product

19.To reduce the risk of electric shock, do not disassemble this product, but take it to an authorized service facility. Opening or removing parts of the product other than specified access doors may expose you to dangerous voltages or other risks. Incorrect reassembling can cause electric shock when the product is subsequently used.

20.You should test the sound reception every time you turn on the units or move one of the components.

21.Periodically examine all components for damage.

22.Be aware of possible loss of privacy while using public airwaves. Conversations may be picked up by other nursery monitors, cordless phones, scanners, etc.

23.Children should be supervised to ensure that they do not play with the product.

24.The product is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction concerning use of the appliance by a person responsible for their safety.

SAVE THESE INSTRUCTIONS

Cautions

Use and store the product at a temperature

between 32oF and 104oF.

Do not expose the product to extreme cold, heat or direct sunlight. Do not put the product close to a heating source.

Batteries should not be exposed to excessive

3. heat such as bright sunshine or fire.

Make sure the baby unit(s) and the adapter

4. cord(s) are always out of reach of the baby, at least 3 feet away from the baby or crib, to avoid a possible strangulation hazard. Never place the baby unit(s) inside the

How do you get warranty service?

To obtain warranty service in the USA, please visit our website at www.vtechphones.com or call 1 (800) 595-9511. In Canada, go to www.vtechcanada.com or call 1 (800) 267-7377.

NOTE: Before calling for service, please review the user’s manual - a check of the Product’s controls and features may save you a service call.

Except as provided by applicable law, you assume the risk of loss or damage during transit and transportation and are responsible for delivery or handling charges incurred in the transport of the Product(s) to the service location. VTech will return repaired or replaced Product under this limited warranty. Transportation, delivery or handling charges are prepaid. VTech assumes no risk for damage or loss of the Product in transit. If the Product failure is not covered by this limited warranty, or proof of purchase does not meet the terms of this limited warranty, VTech will notify you and will request that you authorize the cost of repair prior to any further repair activity. You must pay for the cost of repair and return shipping costs for the repair of Products that are not covered by this limited warranty.

What must you return with the Product to get warranty service?

Other limitations

This warranty is the complete and exclusive agreement between you and VTech. It supersedes all other written or oral communications related to this Product. VTech provides no other warranties for this Product. The warranty exclusively describes all of VTech’s responsibilities regarding the Product. There are no other express warranties. No one is authorized to make modifications to this limited warranty and you

laypen. Never cover the baby

baby’s crib or p

unit(s) or parent unit with anything such as a towel or a blanket. Other electronic products may cause interference with your baby monitor. Try installing your baby monitor as far away from these electronic devices as possible: wireless routers, radios, cellular telephones, intercoms, room monitors, televisions, personal computers, kitchen appliances and cordless telephones.

serial number plates or electronic serial numbers have been removed, altered or rendered illegible; or Product purchased, used, serviced, or shipped for repair from outside the United States of America or Canada, or used for commercial or institutional purposes (including but not limited to Products used for rental purposes); or Product returned without a valid proof of purchase (see item 2 on the next page); or Charges for installation or set up, adjustment of customer controls, and installation or repair of systems outside the unit.

Return the entire original package and contents including the Product to the VTech service location along with a description of the malfunction or difficulty; and Include a “valid proof of purchase” (sales receipt) identifying the Product purchased (Product model) and the date of purchase or receipt; and Provide your name, complete and correct mailing address, and telephone number.

Precautions for users of implanted cardiac pacemakers

Cardiac pacemakers (applies only to digital cordless devices): Wireless Technology Research, LLC (WTR), an independent research entity, led a multidisciplinary evaluation of the interference between portable wireless devices and implanted cardiac pacemakers. Supported by the U.S. Food and Drug Administration, WTR recommends to physicians that:

Pacemaker patients

•

Should keep wireless devices at least six inches from the pacemaker.

•

Should NOT place wireless devices directly over the pacemaker, such as in a breast

pocket, when it is turned ON. WTR’s evaluation did not identify any risk to bystanders with pacemakers from other persons using wireless devices.

Electromagnetic fields (EMF)

This VTech product complies with all standards regarding electromagnetic fields (EMF). If handled properly and according to the instru

user’s manual, the product is safe to be used based on scientific evidence available today.

ctions in this

The RBRC® seal

The RBRC

seal on the nickel-metal battery indicates that VTech Communications, Inc. is voluntarily participating in an industry program to collect and recycle these batteries at the end of their useful lives, when taken out of service within the United States and Canada.

program provides a convenient alternative

The RBRC to placing used nickel-metal batteries into the trash or municipal waste, which may be illegal in your area.

VTech’s participation in RBRC drop off the spent battery at local retailers participating in the RBRC service centers. Please call

1 (800) 8 BATTERY

recycling and disposal bans/restrictions in your area. VTech’s involvement in this program is part of its commitment to protecting our environment and conserving natural resources.

should not rely on any such modification. State/Provincial Law Rights: This warranty gives you

specific legal rights, and you may also have other rights, which vary from state to state or province to province.

Limitations: Implied warranties, including those of fitness for a particular purpose and merchantability (an unwritten warranty that the Product is fit for ordinary use) are limited to one year from the date of purchase. Some states/provinces do not allow limitations on how long an implied warranty lasts, so the above limitation may not apply to you. In no event shall VTech be liable for any indirect, special, incidental, consequential, or similar damages (including, but not limited to lost profits or revenue, inability to use the Product or other associated equipment, the cost of substitute equipment, and claims by third parties) resulting from the use of this Product. Some states/ provinces do not allow the exclusion or limitation of incidental or consequential damages, so the above limitation or exclusion may not apply to you.

Please retain your original sales receipt as proof of purchase.

makes it easy for you to

program or at authorized VTech product

for information on Ni-MH battery

and 1 (800) 8 BATTERY®

RBRC are registered trademarks of Rechargeable Battery Recycling Corporation.

FCC and IC regulations

FCC Part 15

This equipment has been tested and found to comply with the requirements for a Class B digital device under Part 15 of the Federal Communications Commission (FCC) rules. These requirements are intended to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

•

Reorient or relocate the receiving antenna.

•

Increase the separation between the equipment and receiver.

•

Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

•

Consult the dealer or an experienced radio/TV

technician for help. Changes or modifications to this equipment not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. To ensure safety of users, the FCC has established criteria for the amount of radio frequency energy that can be safely absorbed by a user or bystander according to the intended usage of the product. This product has been tested and found to comply with the FCC criteria. The baby unit shall be installed and used such that parts of all persons’ body are maintained at a distance of approximately 8 in (20 cm) or more. The transmitter and antenna of the parent unit shall be held at least 1 in (2.5 cm) from your face. This Class B digital apparatus complies with Canadian requirement: CAN ICES-3 (B)/NMB-3(B)

Industry Canada

This device complies with Industry Canada licenceexempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference, including interference that may cause undesired operation. The term ‘’IC:‘’ before the certification/registration

Technical speciﬁcations

Frequency

Crystal controlled PLL synthesizer

control Transmit

frequency

Channels 5

LCD 35 (x) x 21.2 (y) mm B&W LCD

Nominal effective range

Power requirement

t: 1921.536-1928.448 MHz

Baby uni

Parent unit: 1921.536-1928.448

Maximum power allowed by FCC and IC. Actual operating range may vary according to environmental conditions at the time of use.

Parent unit: 2.4 V Ni-MH battery Baby unit power adapter: Input: 100-120V AC 150mA 60Hz Output: 6V DC 400mA Parent unit power adapter:

100-120V AC 150mA 60Hz

Input: Output: 6V DC 400mA

MHz

VTech Telecommunications 80 0144 01, 80 0144 00 User Manual

Specifications and Main Features

Frequently Asked Questions

User Manual