VTech ia5829 User Manual

Table of Contents

Important Safety Instructions......................................................................................1

Before Y ou Begin ..............................................................................................................3

Parts Check List ..................................................................................................................3

The Handset Layout......................................................................................................4

The Base Unit Layout.........................................................................................................5

Getting Started...................................................................................................................6

Setup........................................................................................................................6

Connecting Power to Base Unit .....................................................................................6

Installation and Charge of Battery ...............................................................................6

Low Battery Indication ......................................................................................7

Battery Care and Maintenance ......................................................................................7

Connecting to Phone Line .............................................................................................7

Check for Dial T one.................................................................................................8

Set Date and Time................................................................................................8

Wall Mounting....................................................................................................8

Basic Operation..............................................................................................................9

Telephone Operation ..................................................................................................9

Handset Operation.........................................................................................9

Base Operation .........................................................................................10

Handset Ringer Style/Battery Save.......................................................................1 1

Set the Dail Mode.........................................................................................11

T emporary T one Dialing........................................................................................1 1

Message Waiting......................................................................................................1 1

Clear Message Waiting Alert....................................................................12

Display Screen Messages .........................................................................................12

Speed Dial Memory.....................................................................................13

Store a Number/Name in Speed Dial Memory ..................................................13

Edit a Number/Name Stored in Memory .........................................................14

Delete a Number/Name Stored in Memory ......................................................14

Dial a Memory Number ....................................................................................15

Reassign Locations in Memory ....................................................................................15

Telephone Directory...........................................................................................16

Store a Number/Name in the Directory ...........................................................16

Edit a Number/Name Stored in the Directory ....................................................17

Delete a Number/Name Stored in the Directory ...............................................17

Dial a Number from the Directory.......................................................................18

Move a Number/Name to the Memory.................................................................18

Caller ID Operation.................................................................................................19

Table of Contents

About Call History .............................................................................................19

Review Call History .........................................................................................19

Delete Records from Call History ..............................................................................19

Dial a Displayed Number...................................................................................20

Store a Call History Record in the Directory.......................................................20

Display Screen Messages.................................................................................20

Additional Information.................................................................................................21

Headset Operation...................................................................................................21

Maintenance..................................................................................................................22

In Case of Difficulty...................................................................................................23

Warranty Statement.................................................................................................25

FCC, ACT A and IC Regulations.................................................................................27

T echnical Specifications......................................................................................30

Important Safety Instructions

When using your telephone equipment, basic safety precautions should always be followed to reduce the risk of fire, electric shock and injury, including the following:

1. Read and understand all instructions.

2. Follow all warnings and instructions marked on the product.

3. Unplug this product from the wall outlet before cleaning. Do not use liquid or aerosol cleaners. Use a damp cloth for cleaning.

4. Do not use this product near water (for example, near a bath tub, kitchen sink or swimming pool).

5. Do not place this product on an unstable surface, such as a table, shelf, or stand. The product may fall, causing serious damage.

6. Slots and openings in the back or bottom of the base unit and handset are provided for ventilation. To protect them from overheating, these openings must not be blocked by placing the product on a soft surface such as a bed, sofa or rug. This product should never be placed near or over a radiator or heat register. This product should not be placed in any area where proper ventilation is not provided.

7. This product should be operated only from the type of power source indicated on the marking label. If you are not sure of the type of power supply in your home, consult your dealer or local power company.

8. Do not allow anything to rest on the power cord. Do not install this product where the cord may have anyone walking on it.

9. Never push objects of any kind into this product through slots in the base or handset as they may touch dangerous voltage points or short out parts that could result in a risk of fire or electric shock. Never spill liquid of any kind on the product.

10. To reduce the risk of electric shock, do not disassemble this product, but take it to an authorized service facility. Opening or removing parts of the base or handset other than specified access doors may expose you to dangerous voltages or other risks. Incorrect reassembling can cause electric shock when the product is subsequently used.

11.Do not overload wall outlets and extension cords as this can result in the risk of fire or electric shock.

12.Unplug this product from the wall outlet and refer servicing to an authorized service facility under the following conditions:

Important Safety Instructions

A. When the power supply cord or plug is damaged or frayed. B. If liquid has been spilled onto the product. C. If the product has been exposed to rain or water. D. If the product does not operate normally by following the operating

instructions. Adjust only those controls that are covered by the operating instructions, as improper adjustment of other controls may result in damage and often requires extensive work by an authorized technician to restore the product to normal operation.

E. If the product has been dropped and the base and/or handset has been

damaged.

F. If the product exhibits a distinct change in performance.

13. Avoid using a telephone (other than cordless) during an electrical storm. There is a remote risk of electric shock from lightning.

14.Do not use the telephone to report a gas leak in the vicinity of the leak.

15.Only put the handset of your telephone next to your ear when it is in normal talk mode.

Before You Begin

Enhanced 5.8GHz Technology - Dual band transmission combines the best of

5.8GHz and 900MHz technologies, providing enhanced performance over standard cordless telephones.

Parts Check List

1. Base Unit

2. Handset

3. Base Power Adaptor

4. Telephone Line Cord

To purchase replacement batteries, visit us on the web at www.vtechphones.com or call VTech Communications, Inc. at 1-800-595-9511. In Canada, call VTech Telecommunications Canada Ltd. at 1-800-267-7377.

5. Battery

6. Belt Clip

7. User’s Manual

8. Wall Mount Bracket

Wall Mount Bracket

Handset

Battery

Belt Clip

Base Unit

Telephone Line Cord

Base Power Adaptor

User’s Manual (English and Spanish)

The Handset Layout

1. Antenna

2. Earpiece

3. LCD

4. Left and Right Arrow Keys

5. Phone/Flash Key

6. Dialing Keys (0-9,*,#)

7. Chan/Delete Key

8. Microphone

9. Headset Jack

10. Select Key

11. Off Key

12. Hold Key

13. Redial/Pause Key

14. Prog Key

The Base Unit Layout

1. Message Light

2. Locate Handset Key

3. Charging/In use Light

4. Telephone Line Jack

5. DC Connector Jack

Setup

Connecting Power to Base Unit

1. Choose a location for the base

near an electrical outlet and a telephone jack. This phone requires a modular telephone jack and a standard electrical outlet (110V

Getting Started

AC) not controlled by a wall switch.

2. Plug the DC connector to the base.

Plug the AC adaptor into an electrical outlet.

Installation and Charge of Battery

1. Install the battery. Use only VTech batteries.

a) Remove battery

compartment cover by pressing on the indentation and sliding downward.

Connect the power cord

Standard electrical outlet

b) Align the two holes in the plug with the

socket pins, then snap the plug into place.

c ) Place the battery in the compartment

with the wires in the lower right corner. d) Replace the battery compartment cover. e) If the battery is not already charged,

place the handset in its base and allow

to charge for 10 - 12 hours (or over-

night). After that, be sure to place the

handset in its base when not in use to

ensure maximum daily performance.

Setup

2. If the phone will not be used for long periods of time, remove the battery to prevent possible leakage.

NOTE: Install the base unit away from electronic equipment, such as personal computers, television sets or microwave ovens. Avoid excessive heat, cold, dust or moisture.

Low Battery Indication: If the battery power becomes low, a low-battery icon will be shown at the lower left

BATTERY LOW

corner of handset display. The handset will beep until you place the handset in the charger. When in standby

1/0 1 12:00

mode, the low-battery display is shown:

Battery Care and Maintenance

• The maximum standby time on a fully charged battery is six days. Average

talk time on a fully charged battery is five hours.

• The battery needs charging when:

— A new battery is installed in the handset. — The phone beeps twice every five seconds. — The screen displays BATTERY LOW and the low battery icon.

• Place the handset in its base so the CHARGING light turns on. The battery

is typically fully charged in 12 hours.

• You can keep the battery fully charged by returning the handset to its base

after each use.

• If you repeatedly get a low battery indicator, even after charging overnight, the

battery should be replaced. Use only VTech batteries.

CAUTION! To reduce the risk of fire or injury to persons or damage to the telephone, read and follow these instructions carefully: Charge the battery provided with or identified for use with this product only in accordance with the instructions and limitations specified in the user’s manual.

Getting Started

Connecting to Phone Line

Before connecting to the phone, make sure to properly charge the battery for at least 10 - 12 hours. Plug one end of the telephone line cord into the jack on the bottom of the base unit. Plug the other end of this cord into the wall jack.

Connect the telephone line cord

Modular telephone jack

Setup

Check for Dial Tone

After the battery is charged, pick up the handset and press PHONE/FLASH. Y ou should hear a dial tone.

Set Date and Time

If you subscribe to caller ID service, the date and time will be set automatically with the first incoming call. If you do not have caller ID service, you can set the date and

Getting Started

time manually:

• Press PROG on the handset.

• Press

• The month is flashing. Press month. Press SELECT.

• The day is flashing. Press day. Press SELECT.

• The hour is flashing. Press hour. Press SELECT.

• The minute is flashing. Press minute. Press SELECT.

• AM or PM is flashing. Press Press SELECT.

Wall Mounting

The wall mount bracket is designed for use on standard wall mount plates only.

1. Run the power and telephone line cords through the slots in the bracket, connecting them to the jacks located on the underside of the base.

2. Plug the AC adapter into an electrical outlet. If the battery has not been previously charged, place the handset in the base, and allow it to charge for 1012 hours (or overnight).

3. Connect the telephone line cord to the wall jack.

or until DATE/TIME is displayed. Press SELECT.

or until the screen displays the correct

or to choose between AM or PM.

4. Line up the tabs on the wall mount bracket with the slots on the bottom of the base unit. Snap the bracket firmly in place.

5. Mount the base on the wall. Position the base unit so the mounting studs will fit into the holes on the wall mount bracket. Slide the base unit down on the mounting studs until it locks into place.

Telephone Operation

Handset Operation

/ CID

• While on a call, press to decrease the volume. A double beep will sound when you reach the minimum setting.

• While phone is not in use, press to display caller ID information.

• While entering number or letters, press to delete last character entered.

(phone) / FLASH

SELECT

• Use SELECT in conjunction with PROG during handset programming.

• While on a call, press to increase the volume. A double beep will sound when you reach the maximum setting.

• While phone is not in use, press to display phonebook entries.

• While entering letters, press to advance cursor.

• To make a call, press then dial the number. or dial the number (use < to backspace and correct digits),

then press (phone)/ FLASH.

• During a call, press to receive an incoming call, if call waiting is activated.

• To answer a call, press this or any key except

(off).

HOLD

• Press to put a call on hold.

• To release hold, press it again or press phone or lift the handset of an extension.

CHAN/ DELETE

• Press to switch to a clear channel while on a call.

• When viewing the all log, press to delete the current record displayed.

• Press and hold to delete all calls log while handset is idle.

(off)

• To end a call, press this key or place handset in base.

• While programming, press

to exit.

• While paging, press to cancel.

REDIAL/P AUSE

• To call last number dialed, press REDIAL/PAUSE, then press (phone)/FLASH

-OR-

• Press (phone)/FLASH then press REDIAL/P AUSE.

• To delete the last number dialed record, press twice while handset is idle.

• While entering numbers, press REDIAL/ P AUSE to insert a dialing pause.

PROG

• Press to enter programming mode with handset idle (on hook).

Basic Operation

Telephone Operation

Base Operation

Message Waiting Indicator

• If you subscribe to telephone company voice mail with a visual message waiting signal, this light flashes, and

MESSAGES WAITING

displays on the handset screen when you

Basic Operation

have voice mail waiting.

In Use/Charging Indicator

• Flashes slowly when the handset is in use.

• Flashes rapidly when a call is on hold.

• Glows steadily when the handset is charging in its base.

Page/Handset Locator

• Press to page the handsets. Press again, press

(off) on handset, or

place handset in the base to cancel the page.

Telephone Operation

Handset Ringer Style/Battery Save

Y ou can select from four dif ferent handset ringer styles, or turn the ringer off and extend the battery life.

1. Make sure the handset is off.

2. Press PROG.

3. Press until the screen displays RINGER: and the current selection.

4. Press SELECT. The current setting blinks, and you will hear a sample of the ring.

5. Press of each ring.

6. Press SELECT to choose the displayed ringer setting.

Set the Dial Mode

If you have touch tone service, the phone is ready to use as soon as the battery is charged. If you have pulse (rotary) service, you’ll need to change the dial mode.

• Press PROG on the handset.

• Press

• Press SELECT. The current setting blinks.

• Press to select TONE or PULSE.

• Press SELECT to save the displayed mode.

or to select RINGER: 1, 2, 3, 4 or (off). You will hear a sample

or until the screen displays DIAL MODE: and the current selection.

Temporary Tone Dialing

If you have pulse (rotary) service only, you can change from pulse to touch tone dialing during a call by pressing * (TONE). This is useful if you need to send touch tone signals for access to telephone banking or long distance services.

1. Dial the number.

2. Press * (TONE). Buttons pressed after this send touch tone signals.

3 . After you hang up, the phone automatically returns to pulse service.

Message Waiting

Your ia 5829 is designed to work with most local and regional telephone service provider's voice messaging systems, providing alerts on both the handset and base unit when new messages come in.

Voice messaging is subscription service, available through most service providers, for a monthly fee. Contact your local telephone company for more information.

When a caller leaves a message in your voice mailbox, the MESSAGE light on the base unit will flash. In addition, the handset will display:

Basic Operation

Telephone Operation

MESSAGES WAITING

5/01 5:40PM

Clear Message Waiting Alert

If you wish to manually turn off the message waiting light:

1. Press PROG.

2. Press

3. Press SELECT, the screen displays:

4. Press or to change from YES or NO.

5. Press SELECT to choose the desired setting. You’ll hear a confirmation tone.

Display Screen Messages

Screen Displays: When:

** RINGING **** RINGING **

** RINGING **

** RINGING **** RINGING **

Basic Operation

CONNECTING...CONNECTING...

CONNECTING...

CONNECTING...CONNECTING...

or until screen displays MESSAGES WAITING.

LIGHT OFF: YES

There is a call coming in. The handset is waiting for a dial tone.

PHONE ONPHONE ON

PHONE ON

PHONE ONPHONE ON SCANNING...SCANNING...

SCANNING...

SCANNING...SCANNING...

** PAGING **** PAGING **

** PAGING **

** PAGING **** PAGING ** HOLDHOLD

HOLD

HOLDHOLD BATTERY LOWBATTERY LOW

BATTERY LOW

BATTERY LOWBATTERY LOW NO CONNECTNO CONNECT

NO CONNECT

NO CONNECTNO CONNECT

MESSAGES WAITINGMESSAGES WAITING

MESSAGES WAITING

MESSAGES WAITINGMESSAGES WAITING

RINGER OFFRINGER OFF

RINGER OFF

RINGER OFFRINGER OFF

The handset is in use. The handset is changing to another of the 30

channels available. The base is paging the handset.

There is a call on hold. The battery needs to be recharged.

Displays and a sad tone sounds when the base power is off and

Y ou have been alerted by the telephone company that you have received new voice mail.

The ringer is turned off.

(phone) / FLASH is pressed.

Speed Dial Memory

You can store up to nine telephone numbers with names (up to 15 characters and 24 digits in each location) into the speed dial memory locations you assign (1 through 9). You can also store telephone numbers with names alphabetically in the directory. See

Telephone Directory for instructions.

NOTES:

• The entries you store in speed dial memory will be marked with 01 through 09 in the

telephone directory.

• Press (off) at any time to exit memory mode.

Store a Number/Name in Speed Dial Memory

1. Press PROG on the handset.

2. Press or until the screen displays SPEED DIAL.

3. Press SELECT. The screen displays ENTER 1-9.

NOTE: When memory is full the screen displays MEMORY FULL, an error tone sounds, and you cannot store a new number until you delete a record in speed dial memory or telephone directory.

4. Press the key (1 through 9) for the memory location where you’re storing this entry. The screen displays ENTER NAME.

NOTE: If the location is not empty, your new entry will be stored in place of the old and the first entry will be deleted. Take caution to not save over entries you do not wish to delete from memory.

5. Using the chart below, enter up to 15 characters for the name you’re storing with the

number. Use to backspace and make corrections; use to advance and add a

space.

Presses

Dial Key 1 2 3 4 5 6

Basic Operation

1: 1 2: ABC2 3: DEF3 4: GHI 4 5: JKL5 6: MNO6 7: PQRS7 8: TUV8 9: WX Y Z 9 0: 0

& ’ ,-.#

Telephone Memory

6. When you finish entering the name, press SELECT or PROG. The screen displays ENTER NUMBER.

7. Enter the telephone number. Use to backspace and make corrections. Press REDIAL/PAUSE to store a pause in the dialing sequence.

-OR-

Press REDIAL/PAUSE to display the last number dialed from this phone.

8. Press SELECT or PROG to store your entry . The screen displays DISTINCT RING? and the current setting.

9. Press or to change the setting. Choose Y (for yes) if you wish the phone to alert you to calls from this number by changing to a distinctive ringing pattern after the first ring. Choose N for a normal ringing pattern.

10. Press SELECT or PROG to confirm your selection. If you chose Y, a D will be displayed with the memory entry.

Edit a Number/Name Stored in Memory

1. Press and hold the memory location key (1 through 9) of the entry you wish to edit.

2. When the screen displays the entry you want to edit, press SELECT. Then press or until EDIT flashes.

SPEED EDIT ERASE 8005959511

Basic Operation

3. Press SELECT. The screen displays the name and number. The cursor

appears at the end of the name. Use , and the dial pad keys to edit the name. Press SELECT to move on to edit the number. Use to backspace and make corrections. Press SELECT to move to edit the distinctive ring setting.

4. Press SELECT to save the edited information

Delete a Number/Name Stored in Memory

1. Press and hold the memory location key (1 through 9) of the entry you wish to delete.

2. When the screen displays the entry you want to delete, press SELECT. Then press or until ERASE flashes.

SPEED EDIT ERASE 8005959511

3. Press SELECT. The screen displays ERASE NO YES and the number .

4. Press or until YES flashes.

5. Press SELECT.You’ll hear a confirmation beep.

+ 38 hidden pages