Vs sassoon VSM7575A User Manual

THEVDOUBLE

TOOL TIPS

for the dual blade self-cut clipper

for a faded or short even cut.

VSM7575A

1

HEY YOU!

TAKE A BOW FINE SIR.

THINGS ARE LOOKING UP

& YOU’VE JUST MADE A

QUALITY PURCHASE

WITH THIS NEW GROOMING TOOL.

WE KNOW YOU’VE GOT THIS, BUT BEFORE YOU JUMP INTO
USING YOUR NEW SIDE KICK, HERE’S A FEW TIPS & TRICKS
TO KNOW BEFORE LETTING YOUR CREATIVITY RUN LOOSE.

HIT UP VSFORMEN.COM.AU FOR MORE GROOMING & INSPIRATION +
HANDY VIDEOS ON HOW TO GET THE MOST OUT OF YOUR NEW V DOUBLE.

2

THE V DOUBLE / TOOL TIPS

3

THE V DOUBLE / TOOL TIPS

THE V DOUBLE

BRAVO. YOU’VE MADE A QUALITY PURCHASE.
The V Double is the dual blade self-cut clipper for a faded
or short even cut.

6

3

8

2

7

12

11

4

5

8 7

1

9

1. Innovative dual blades

2. Diamond sharpened
blades

3. Lithium-ion power

4. DC direct drive motor

5. Cordless use

44

6. Ergonomic design
fits i n the palm of
your hand

7. 4 co mb guides - Gra des
#1 - 4 (3mm to 13mm )

8. Ear taper cutting comb
guide

9. Removable, washable
blades

10. Storage pouch

11. Cleaning brush

12. Oi l

10

PREPPING YOUR
NEW TOOL

CHARGING

The V Double is so easy to use. Bu t before you start using your new tool, you
must take the time to charge it f or 3 hours before it s first use. Your new tool
comes w ith a small amount of charge, but the initial super charge will ensure
your new tool will have optimum power per formance to give you smooth fast
cutting, every time.

- Before using for the first time, fully charge your new tool continuously for
3 hours.

- Maximum battery capacity will only be reached after 3 charging &
discharging cycles.

- Ensure your new tool is switched off.

- Inser t the small plug on the charging adaptor into the socket on the side of
your new tool.

- Plug the charging adaptor into a suitable mains power socket and switch on.

- The red charging L ED indictor light on your new tool will flash when correctly
connected to the mains power. When it is fully charged, the red charging LED
indicator light w ill remain on.

- A full charge will supply 60 minu tes cordless runtime.

- A quick charge of 30 minutes will supply 15 minutes cordless runtime.

- When the clipper is about to run out of energy, the charging LED indicator
light will flash to indicate that ther e is less than 15% battery capacity
remaining.

- To maintain optimum capacity of the li-ion battery, it is highly recommended
to fully discharge & then recharge your t ool for 3 hours every 6 months.

THE V DOUBLE / TOOL TIPS

5

THE V DOUBLE / TOOL TIPS

WARNING: IF THE CHARGING LIGHT SUDDENLY STARTS
TO FLASH RAPIDLY, THE APPLIANCE IS FAULTY. IF THIS
DOES HAPPEN, PLEASE STOP CHARGING AND REMOVE THE
ADAPTER FROM THE POWER SOURCE AND CONTACT OUR
CUSTOMER CARE CENTRE FOR FUTHER ADVICE.

6

THE V DOUBLE / TOOL TIPS

OILING THE BLADES

To get the sharpest, most precise cut, it is highly recommended to oil the blades
before each use.

Using the oil supplied with your new tool, unscrew the cap & cut o ff the ver y end
of the plastic tube with a pair of scissors to release the oil .

Switch your tool on, gently squeeze the oil tube & apply 5 drops of oil onto both
side of the dual blades. Leave the tool on f or a further few seconds to allow the
oil to thoroughly spread across each of the blades. Switch off the tool & remove
any excess oil by gently dabbing with a cloth.

TO GET THE SHARPEST, MORE PRECISE CUT,
IT IS HIGHLY RECOMMENDED TO OIL THE BLADES
BEFORE EACH USE.

7

THE V DOUBLE / TOOL TIPS

GETTING TO KNOW
YOUR NEW TOOL

The V Double has an ergonomically designed head to f it in the palm of your
hand for an easy ‘DI Y’ hair cut. It is similar to a traditional clipper, but with the
convenience of 2 blade sets, instead of 1.
The V Double allows you to keep it long on top & faded on the sides or short
all-over. You decide.

A MODERN TAKE ON THE TRADITIONAL CLIPPER

Just like riding a bike, new things can take some prac tice, and The V Double Cut
is no dif ferent. The more you use it, the more comfor table you become.
This clipper has been designed with a dual blade system, so its quite similar
to how to use a traditional clipper to self-cut, but its made even easier w ith
additional of the dual blade system.

FOR AN ALL-OVER SHORT CUT

Start cutting at the back of the head, near the nape of the neck. Hold your new
tool with the teeth of the clipper point ing upwards, so that the comb guide is flat
on the head. Slowly move the clipper upwards through the hair and towards the
front of the head in a f orwards sweeping motion. Once at the front of the head,
engage t he opposite blade in a backwar d sweeping motion to move from the
front of the head, to the nape of the neck.
Continue with this sweeping cutting motion, running from the nape of the neck to
the front of the head until you reach an all- over same leng th.

8