VQ Models VQA090, VQA091 Instruction Manual

DORNIER

Radio control model R/C Flugmodell

MONTAGEANLEITUNG

INSTRUCTION MANUAL

SPECIFICATIONS

Wingspan 63 in. Length 47.6 in. Electric Motor (See next page) Glow Engine .46 2Stroke / .52 4-Stroke Radio 6 Channel / 6-7 Servos

WARNING!

ACHTUNG!

This radio controlled model is NOT a toy. If modified or flown carelessly it could go out of controll and cause serious human injury or property damage. Before flying your airplane, ensure the air field is spacious enough. Always fly it outdoors in safe areas and seek professional advice if you are unexperienced.

Dieses ferngesteuerte Modell ist KEIN Spielzeug! Es ist für fortgeschrittene Modellflugpiloten bestimmt, die ausreichende Erfahrung im Umgang mit derartigen Modellen besitzen Bei unsachgemäßer Verwendung kann hoher Personen- und/oder Sachschaden entstehen. Fragen Sie in einem Modellbauverein in Ihrer Nähe um professionelle Unterstützung, wenn Sie Hilfe im Bau und Betrieb benötigen. Der Zusammenbau dieses Modells ist durch die vielen Abbildungen selbsterklärend und ist für fortgeschrittene, erfahrene Modellbauer bestimmt.

TECHNISCHE DATEN

Spannweite 1620mm Lange 1210mm Elektroantrieb (siehe nächste Seite) Verbrennerantrieb 7.5cc 2-T / 8.5cc 4-T Fernsteuerung 6 Kanal / 6-7 Servos

PICHLER

ARF BY

DO-27

Designed for brushless electric motors Entwickelt für Brushless Elektro Motoren

(.46-.52 class glow conversion optional)

(7,5 -8,5cc Glühzündermotor Einbau möglich)

VQ No: VQA090

VQ No: VQA091

.........................................................

1.5mm

A

B

!

CA

L/R

Assemble left and right sides the same way.

X

Drill holes using the stated

size of drill (in this case 1.5 mm Ø)

Use epoxy glue

Take particular care here

Hatched-in areas:

remove covering

film carefully

Not included. These parts must be

purchased separately

Check during assembly that these

parts move freely, without binding

Apply cyano glue

SILICON

EPOXY A

EPOXY B

CA

Epoxy Glue (30 minutes type)

Silicon Glue

Cyanoacrylate Glue

Sekundenkleber

Epoxy-Klebstoff (30min)

6 - channel radio

RECOMMENDED ACCESSORIES (Purchase separately)

6 - Kanal Fernsteuerung

Egänzungskit Verbrenner

(Tank + Motorträger) Best.Nr. C4165

Empfohlenes Zubehör (Nicht im Lieferumfang enthalten)

Antrieb Standard:

Antrieb Tuning (Kraftvoller Kunstflug):

BOOST 40 Brushless Combo Set, Best.Nr. C2983 LiPo Battery RED POWER 3200-3S, Best.Nr. C3164 Luftschraube 12*6, Best.Nr. C1937

BOOST 60 Brushless Combo Set, Best.Nr. C3174 LiPO Akku RED POWER 4250-5S, Best.Nr. C4547 Luftschraube 13*8, Best.Nr. C2846

Silikonkleber

Tool Required/ Empfohlenes Werkzeug

The pre-covered film on ARF kit may wrinkle due to variations of temperature. Store model in a cool and dry place for awile. Then, staring with low heat, you may carefully use a hair dryer to smooth out wrinkels.

Die Bespannung des Modells kann durch Temeratureinflusse erschlaffen oder Falten werfen z.b bei zu starker Sonnenenstrahlung oder Hitze. Stellen Sie das Modell zunachst an einen kuhlen Platz fur eine bestimmte Zeit. Danach konnen Sie versuchen die restlichen Falten vorstichtig mit einem Haartrockner zu behandeln.

!

CONVERSION TABLE

1.0mm = 3/64”

1.5mm = 1/16”

2.0mm = 5/64”

2.5mm = 3/32”

3.0mm = 1/8”

4.0mm = 5/32”

5.0mm = 13/64”

6.0mm = 15/64”

10mm = 13/32” 12mm = 15/32” 15mm = 19/32” 20mm = 51/64”

25mm = 1” 30mm = 1-3/16” 45mm = 1-51/64”

1 x Servo S4020

(für Seitenruder) Best.Nr. C1687

3 x Servo S4020

(für Höhen- und Querruder) Best.Nr. C4995

2 X Servo DS3012

(Fur Landeklappen)

# C4995

Full the elevator out of the horizontal stabilizer.

Cut away only the film both side

1A

1B

1

When you are satisfied with the alignment, use a pencil to trace around the top and bottom of the stabilizer where it meets the fuselage.

Cut away only the covering both side

B

B’

B=B’

Aluminum wing joiner

Remove the horizontal stabilizer from the fuselage. Using the sharp hobby knife, carefully cut away the covering inside the lines which were marked above.

* WARNING: When removing any covering from the airframe, please ensure that you secure the cut edge with CA or similar cement. This will ensure the covering remain tight.

Stabilizer

A

A’

A=A’

Stabilizer

FUSELAGE

Again, Install the horizontal stabilizer into the fuselage and adust the alignment as described in steep 1C. Secure the horizontal stabilizer in place using CA glue.

1C

1D

1E

Note: The slots for the control horn installation are pre- cut at factory.

Control horn

...........2

CA

Thin CA glue

Push the elevator and its hinges into the hinge slots in the trailing edge of the horizontal stabilizer. There should be a minimal hinge gap. When satisfied with the and alignment, hinge the elevator to the horizontal stabilizer using CA glue.

Hinge

STABILIZER

CA

Apply thin CA to both side of the hinge

Full the rudder out of the vertical stabilizer.

1F

1G

1H

2

2A

2B

WARNING! Securely glue together. If coming off during flights, you lose control of your airplane which leads to accidents !

Vergewissern Sie sich, sauber geklebt zu haben. Andernfalls konnen Probleme mit der Flugeigenschaft auftreten!

CA

First, reposition the elevator connector in place, secure it in place using thin CA glue.

Elevator connector

CA

Cut away only the covering both side

Realign the vertical stabilizer, then glue

the vertical stabilizer into the fuselage,

using a generous amount of thin CA.

CA

Thin CA glue

Hinge

STABILIZER

CA

Apply thin CA to both side of the hinge

Push the rudder and its hinges into the hinge slots in the trailing edge of the horizontal stabilizer. There should be a minimal hinge gap. When satisfied with the and alignment, hinge the elevator to the horizontal stabilizer using CA glue.

2D

2E

2F

2G

WARNING! Securely glue together. If coming off during flights, you lose control of your airplane which leads to accidents !

Vergewissern Sie sich, sauber geklebt zu haben. Andernfalls konnen Probleme mit der Flugeigenschaft auftreten!

When you are satisfied with the alignment, use a pencil to trace around the right and left of the stabilizer where it meets the fuselage.

2C

CA

A

B

A

A=38mm

2mm

Drill a 2mm diameter hole in torque rod mounting slot, marking sure that you drill the hole perpendicular to the leading edge of the rudder.

2H

25mm tail wheel

2mm collar

Note: The slots for the control horn installation pre- cut at factory.

Control horn

...........1

............4

4X20mm screw

2G

3

3A

............2

4X30mm screw

4mm nut-washer

4mm washer

4mm nut

4x30mm screw

Aluminum landing gear

CA

WARNING! Securely glue together. If coming off during flights, you lose control of your airplane which leads to accidents !

Vergewissern Sie sich, sauber geklebt zu haben. Andernfalls konnen Probleme mit der Flugeigenschaft auftreten!

3B

3C

Remove the plywood motor mounting plate and drill a 5mm hole through the fire-wall at each of the four marks marked above (D).

5mm

13/64”

Using a aluminum motor mounting plate as a template, mark the plywood motor mounting plate where the four holes are to be drilled (A). Remove the aluminum motor mounting plate and drill a 3mm hole through the plywood at each of the four marks marked (B).

Using a plywood motor mounting plate as a template, mark the firewall where the four holes are to be drilled (C) .

! Align the mark on plywood motor mounting with the center mark on the fire-wall

!

Aluminum motor mounting plate (included with electric motor set)

Plywood motor mounting

A

B

C

E

5mm

13/64”

Push the four 5x35mm bolts through the fire-wall as shown (E)

Reposition the plywood motor mounting plate and secure it in place with twelve 5xmm nuts and washers (E).

Pull the magnetic battery hatch out of the fuselage

4C

5

5A

5B

5C

5D

5E

F

Firewall

113mm

B’

B

B=B’

A

A=A’

A’

! Engine thrust on balk head

is already adjust at factory

Attach the aluminum motor mounting plate on to the motor and secure it in place with four screws ( included with motor set) (F).

TOP-VIEW / Draufsicht

SIDE-VIEW / Seitenansicht

Sturz und Zug beachten!

Sperrholztrager Platten zusammenkleben, wie gezeigt ausrichten und Locher bohren. Motor nach untenstehendem Schema einbauen. Fur optimale Leistung empfehlen wir folgende Komponenten:

-Brushless-Motor PICHLER BOOST 60

-Brushless Regler PICHLER XQ-70

-LiPO Akku LEMONRC 3700-5S

-Luftschraube 12*6 - 13*8

For maximum performance, we recommended the following:

-Brushless-Motor PICHLER BOOST 60

-Brushless Regler PICHLER XQ-70

-LiPO Battery LEMONRC 3700-5S

-Propeller 12*6 - 13*8

Throttle pushrod

FRONT

Elevator pushrod

Elevator servo

Rudder servo (mini servo)

Throttle servo

BOARD - TOP VIEW

FUSELAGE - BOTTOM VIEW

The holes for the rudder servo are Pre-cut at factory (left and right side of the fuselage).

Cut away only the covering

Akku Kiettband aus dem PICHLER

Sortiment Best.Nr. C4739

Battery seat bell

X

Tipp

5F

6

6A

6B 6C

1.5mm

1/16

2mm

L/R

X

BOTTOM - VIEW / Unteransicht

Cut here for standard servo

Aileron & flap extension cord

Trial fit the control horn into the slot. If the parts will join, but with a gaps, sand or trim the parts a little at a time until the parts meet exactly with no gaps.

CA

Plastic control horn

Linkage Stopper set

.....................4

.................4

1.2mm O Alenk-Gestange

Aileron & flap pushrod

CA

Do the same way with other wing half

Metal hook (x2)

Spring (x1)

L/R

Do the same way with other wing half

7

8

9

65 ~ 70mm

20mm

10mm

Aileron /

Rudder

Elevator /

10mm

20mm

Querruderausschlag

Hohenruderausschlag

Seitenruderausschlag

Do not try to fly an out-of balance model!

Uberprufen Sie vor dem Flug den Schwerpunkt.

IMPORTANT:

Please do not clean your model with pure alcohol, only use liquid soap with water or use glass cleaner to clean on surface of your model to keep the colour not fade.

All details are subject to change without notice !

Technische Anderungen und Irrtumer vorbehalten !

25mm Landing / Landung

Fflap / Landeklappen

10

Note: Cut out the stickers and apply them in the proper area. Do not peel the backing paper off all at once. Peel off one corner of the backing and cut off with scissors. Arrange sticker on model and when satisfied adhere the corner without backing. Carefully peel back the rest of the backing while at the same time adhering the rest of the sticker.

Try not to make air bubbles, if there are some, carefully puncture sticker (center of bubble) but not model surface with the tip of the knife or sharp pin and squeeze out the air. At curves stretch sticker and apply a little heat so that no ceases occur. Cut off the excess that is produced.

11

12

15mm Take off / Start

CG

.........................................................

1.5mm

A

B

!

CA

L/R

Assemble left and right sides the same way.

X

Drill holes using the stated size of drill

(in this case 1.5 mm Ø)

Use epoxy glue

Take particular care here

Hatched-in areas:

remove covering

film carefully

Not included. These parts must be

purchased separately

Check during assembly that these

parts move freely, without binding

Apply cyano glue

SILICON

EPOXY A

EPOXY B

CA

Epoxy Glue (30 minutes type)

Silicon Glue

Cyanoacrylate Glue Sekundenkleber

Epoxy-Klebstoff (30min)

6 - channel radio

RECOMMENDED ACCESSORIES (Purchase separately)

6 - Kanal Fernsteuerung

Egänzungskit Verbrenner

(Tank + Motorträger) Best.Nr. C4165

Empfohlenes Zubehör (Nicht im Lieferumfang enthalten)

Antrieb Standard:

Antrieb Tuning (Kraftvoller Kunstflug):

BOOST 40 Brushless Combo Set, Best.Nr. C2983 LiPo Battery RED POWER 3200-3S, Best.Nr. C3164 Luftschraube 12*6, Best.Nr. C1937

BOOST 60 Brushless Combo Set, Best.Nr. C3174 LiPO Akku RED POWER 4250-5S, Best.Nr. C4547 Luftschraube 13*8, Best.Nr. C2846

Silikonkleber

Tool Required/ Empfohlenes Werkzeug

The pre-covered film on ARF kit may wrinkle due to variations of temperature. Store model in a cool and dry place for awile. Then, staring with low heat, you may carefully use a hair dryer to smooth out wrinkels.

Die Bespannung des Modells kann durch Temeratureinflusse erschlaffen oder Falten werfen z.b bei zu starker Sonnenenstrahlung oder Hitze. Stellen Sie das Modell zunachst an einen kuhlen Platz fur eine bestimmte Zeit. Danach konnen Sie versuchen die restlichen Falten vorstichtig mit einem Haartrockner zu behandeln.

!

CONVERSION TABLE

1.0mm = 3/64”

1.5mm = 1/16”

2.0mm = 5/64”

2.5mm = 3/32”

3.0mm = 1/8”

4.0mm = 5/32”

5.0mm = 13/64”

6.0mm = 15/64”

10mm = 13/32” 12mm = 15/32” 15mm = 19/32” 20mm = 51/64”

25mm = 1” 30mm = 1-3/16” 45mm = 1-51/64”

1 x Servo S4020

(für Seitenruder) Best.Nr. C1687

3 x Servo S4020

(für Höhen- und Querruder) Best.Nr. C4995

2 X Servo DS3012

(Fur Landeklappen)

# C4995

VQ Models VQA090, VQA091 Instruction Manual

Specifications and Main Features

Frequently Asked Questions

User Manual