VQ Models TIGER MOTH DH-82 Instructions Manual

SPECIFICATIONS

Wingspan:......................................1400mm

Length:...........................................1180mm

Electric Motor:....................................750W

Glow Engine:.................... .46 2-T / .70 4-T

Radio:....................5 Channel / 4-5 Servos

Function: Ailerons-Elevator-Rudder-Throttle

WARNING! This radio controlled model is NOT a toy. If modified or flown carelessly it could go out of controll and cause serious human injury or property damage. Before flying your airplane, ensure the air field is spacious enough. Always fly it outdoors in safe areas and seek professional advice if you are unexperienced.

ACHTUNG! Dieses ferngesteuerte Modell ist KEIN Spielzeug! Es ist für fortgeschrittene Modellflugpiloten bestimmt, die ausreichende Erfahrung im Umgang mit derartigen Modellen besitzen. Bei unsachgemässer Verwendung kann hoher Personen- und/oder Sachschaden entstehen. Fragen Sie in einem Modellbauverein in Ihrer Nähe um professionelle Unterstätzung, wenn Sie Hilfe im Bau und Betrieb benötigen. Der Zusammenbau dieses Modells ist durch die vielen Abbildungen selbsterklärend und ist für fortgeschrittene, erfahrene Modellbauer bestimmt.

R/C Flugmodell R/C Airplane Model

ALL BALSA, PLYWOOD CONSTRUCTION AND ALMOST READY TO FLY

Anleitung / Instructions

TECHNISCHE DATEN

Spannweite ...................................1400mm

Lange ............................................1180mm

Elektroantrieb.................................... 750W

Verbrennerantrieb ...............7.45cc - 11.5cc

Fluggewicht .......................................3,5Kg

Fernsteuerung ........ 5 Kanal / 4 .. 5 Servos

RTF Weight: 3.Kg (will vary with equipment use)

TIGER MOTH

DH-82

VQ No: VQA139R/Y/DK

1.5mm

A

B

!

CA

L/R

Assemble left and right sides the same way.

X

Drill holes using the stated size of drill

(in this case 1.5 mm )

Use epoxy glue

Take particular care here

Hatched-in areas:

remove covering film carefully

Not included. These parts must be

purchased separately

Check during assembly that these

parts move freely, without binding

Apply cyano glue

5min Epoxy

CA

Klebstoff /Glue

5-Minute Epoxy, # X3598-120

Sekundenkleber / CA Glue, # X3572

Luftschraube 12x5 (Holz), # C9714‚

Servokabelverlängerung x2, # C2036

Werkzeug / Tools

Hobby knife

Needle nose Pliers

Phillip screw driver

Awl

Scissors

Wire Cutters

(nicht im Lieferumfang / not included)

Hex Wrench

.........................................................

Sander

Masking tape - Straight Edged Ruler - Pen or pencil - Drill and Assorted Drill Bits

Read through the manual before you begin, so you will have an overall idea of what to do.

Symbols used throughout this instruction manual, comprise:

(separat erhältlich - available seperately)

CONVERSION TABLE

1.0mm = 3/64”

1.5mm = 1/16”

2.0mm = 5/64”

2.5mm = 3/32”

3.0mm = 1/8”

4.0mm = 5/32”

5.0mm = 13/64”

6.0mm = 15/64”

10mm = 13/32” 12mm = 15/32” 15mm = 19/32” 20mm = 51/64”

25mm = 1” 30mm = 1-3/16” 45mm = 1-51/64”

If exposed to direct sunlight and/or heat, wrinkels can appear. Storing the model in a cool place will let the wrinkles disappear. Otherwise, remove wrinkles in covering film with a hair dryer, starting with low temperature. You can fix the edges by using a hot iron.

Bei Sonneneinstrahlung und/oder Wärme kann die Folie erschlaffen bzw. Falten entstehen. Verwenden Sie einen Haartrockener, um die Folie ggf. zu spannen. Die Kanten können Sie vorsichtig mit einem Bügeleisen behandeln. Nicht zuviel Hitze anwenden !

Für den Betrieb erforderlich / Items needed

Low seting

Brushless Power Set BOOST 40 # C9109

LiPo Akku 4500 - 11,1V # C9421

LiPo Battery 4500- 11,1V

Servokabelverlängerung x2, # C1393

Servo Extensionwire

Propeller 12x5 (Wooden)

MASTER SERVO DS3012MG x2, # C7578

MASTER SERVO DS4020 x2, # C4994

Fernsteuerung GigaProp 6 # C8802

Radio Set GigaProp 6

Akku Klettbänder # C4738

Battery Straps

www.pichler-modellbau.de

Passendes Zubehör finden Sie hier:

Find all suitable accessories here:

Using a pencil or felt tipped pen, mark the fire wall where the four holes are to be drilled

5mm

13/64”

Remove the engine mount and drill a 13/64”(5mm) hole through the fire-wall at each of the four marks marked.

Attach the four blind-nut to the fire-wall as show

4mm

! Align the mark on both mounts with the mark on the fuselage

! Engine thrust on balk head is already adjust at factory

Engine mounts Front-view

LEFT

RIGHT

A

B

B’

B=B’

..........4

4mm Blind-nut

1- Engine installation

1A

1B

1C

1D

1E

FIRE-WALL

FUSELAGE - BOTTOM VIEW

130mm

Note: Apply Silicon sealer to each of the 3x25mm screw.

Reposition the engine mounts on to the fire-wall and secure them with four 4x25mm screw.

Reposition the engine on to the engine mounts so the distance from the prop hub to the fire wall is 130mm.

- Mark the engine mounting plate where the four holes are to be drilled. Note: Mark the mounting plate through the engine mounting flanges.

- Remove the engine and drill a 1/8”(3mm) holes through the beam at each of the four marks made above.

- Reposition the engine on the engine mount beams, aligning it with the holes. Secure the engine to the engine mount using four 1/8x51/64”(3x25mm) screws.

...................4

....................4

4x25mm screw - washer

3x25mm screw - washer

2- Engine installation

2A

2B

2C

Using a wooden motor mounting plate as a template, mark the fire-wall where the four holes are to be drilled.

Remove the wooden motor mounting plate and drill a 5mm hole through the fire-wall at each of the four marks marked .

5x70mm bolt.....4

5mm nut..........12

5mm washer...16

Attach the four 5x70mm bolts and nuts to the fire-wall as shown.

3mm bolt / nut...4

Secure the Motor to the wooden motor mounting plate using the four 3mm bolts.

Using a aluminum motor mounting plate as a template, mark the plywood motor mounting plate where the four holes are to be drilled.

3A

Remove the aluminum motor mounting plate and drill a 1/8”(3mm) hole through the plywood at each of the four marks marked .

3mm

3B

FUSELAGE - TOP VIEW

B

B’

FIRE-WALL

! Align the mark on wooden motor mounting plate with the mark on the fire-wall.

5mm

130mm

3- Electric Motor installation

3C

3D

3F

3E

3G

Full the elevator out of the horizontal stabilizer.

Cut away only the covering both side

Trial fit the horizontal stabilizer in place. Check the alignment of the horizontal stabilizer.

If the parts will join, but with a gaps, sand or the rectangular hole on the fuselage a little at a time until the parts meet exactly with no gaps.

* WARNING: When removing any covering from the airframe, please ensure that you secure the cut edge with CA or similar cement. This will ensure the covering remain tight.

When you are satisfied with the alignment, use a pencil to trace around the top and bottom of the stabilizer where it meets the fuselage.

Remove the horizontal stabilizer from the fuselage. Using the sharp hobby knife, carefully cut away the covering inside the lines which were marked above.

Cut away only the covering both side

4- Horizontal Stabilizer

4A

4B

4C

4D

A

A’

A=A’

HORIZONTAL

STABILIZER

TOP VIEW

VQ Models TIGER MOTH DH-82 Instructions Manual

Specifications and Main Features

Frequently Asked Questions

User Manual