VQ Models SIAI MARCHETTI SF-260, VQA143GE, VQA143IT, VQA143US Instruction Manuals
SPECIFICATIONS
Wingspan:.........................1630mm (64.1in)
Length:..............................1300mm (51.1in)
Electric Motor:.....................See next pager
Glow Engine:.................... .55 - .61 2T
RTF Weight: 3.9Kg / 8.6lbs (Will vary with
Equipment Used).
Radio:......................8 Channel / 6-7 Servos
Function: Ailerons-Elevator-Rudder-Throttle
Flaps-Optional Retractable Landing Gear.
WARNING! This radio controlled model is NOT a toy. If modified or flown carelessly it could go out of controll and
cause serious human injury or property damage. Before flying your airplane, ensure the air field is spacious enough.
Always fly it outdoors in safe areas and seek professional advice if you are unexperienced.
ACHTUNG! Dieses ferngesteuerte Modell ist KEIN Spielzeug! Es ist für fortgeschrittene Modellflugpiloten bestimmt,
die ausreichende Erfahrung im Umgang mit derartigen Modellen besitzen. Bei unsachgemässer Verwendung kann
hoher Personen- und/oder Sachschaden entstehen. Fragen Sie in einem Modellbauverein in Ihrer Nähe um
professionelle Unterstätzung, wenn Sie Hilfe im Bau und Betrieb benötigen. Der Zusammenbau dieses Modells ist
durch die vielen Abbildungen selbsterklärend und ist für fortgeschrittene, erfahrene Modellbauer bestimmt.
Radio control model / Flugmodel
ALL BALSA, PLYWOOD CONSTRUCTION AND ALMOST READY TO FLY
SIAI MARCHETTI
Instruction manual / Montageanleitung
TECHNISCHE DATEN
Spannweite:...................................1630mm
Lange:............................................1300mm
Elektroantrieb.............(siehe nächste Seite)
Verbrennerantrieb:...............................10cc
Fluggewicht:.......................................3.9Kg
Fernsteuerung.............8 Kanal / 6-7 Servos
VQ No: VQA143GE - VQA143US - VQA143IT
SF-260
EP GP
Minimum 8 channel radio
for airplane with 7 servos
12x6 for .58 - 2 cycle engine
12x7 for .61 - 2 cycle engine
14x8 for Electric motor
Silicone tube
.55 ~ .61 - 2 cycle
.Motor control x1 .Aileron x 2
.Flap x 2 .Elevator x1 .Rudder x1
SILICON
EPOXY A
EPOXY B
CA
GLUE /
Epoxy Glue ( 5 minute type)
Silicon sealer
Cyanoacrylate
Glue
Epoxy Glue (30 minute type)
Hobby knife
Needle nose Pliers
Phillip screw driver
Awl
Scissors
Wire Cutters
Hex Wrench
.........................................................
.........................................................
.........................................................
.........................................................
.........................................................
.........................................................
.........................................................
.........................................................
.........................................................
.........................................................
.........................................................
Sander
Masking tape - Straight Edged Ruler - Pen or pencil - Rubbing alcohol - Drill and Assorted Drill Bits
REQUIRED ITEMS / Zum Betrieb wird benotigt
KLEBSTOFF
1.5mm
A
B
!
CA
L/R
Assemble left and right
sides the same way.
X
Drill holes using the stated
size of drill
(in this case 1.5 mm Ø)
Use epoxy glue
Take particular care here
Hatched-in areas:
remove covering
film carefully
Not included.
These parts must be
purchased separately
Check during assembly that these
parts move freely, without binding
Apply cyano glue
!
If exposed to direct sunlight and / or heat, wrinkles can appear. Storing the model in a coll
place will let the wrinkles disappear. Otherwise, remove wrinkles in covering film with a hairdryer, starting with low temperature. You can fix the corners by using a hot iron.
Bei Sonneneinstrahlung und / oder Warme kann die Folie erschlaffen bzw. Falten entstehen.
Verwenden Sie ein Warumluftgeblase (Haartrockner) um evtl. Falten aus der Folie zu
bekommen. Die Kanten konnen Sie mit einem Bugeleisen behandeln. Nicht zuviel Hitze
anwenden
Read through the manual before you begin, so you will have an overall idea of what to do.
CONVERSION TABLE
1.0mm = 3/64”
1.5mm = 1/16”
2.0mm = 5/64”
2.5mm = 3/32”
3.0mm = 1/8”
4.0mm = 5/32”
5.0mm = 13/64”
6.0mm = 15/64”
10mm = 13/32”
12mm = 15/32”
15mm = 19/32”
20mm = 51/64”
25mm = 1”
30mm = 1-3/16”
45mm = 1-51/64”
Li-Po Battery
5.300 - 22.2v
ESC 80A
Motor Brushless
1000 Watt
Extension cord for aileron servos: 50cm(x2)
Extension cord for flap servos: 50cm(x4)
Extension cord for retract servos: 30cm(x2)
Extension cord for Rx battery pack: 20cm(x1)
WING BOTTOM-VIEW
Using the thread (pre-installed at factory)
to slide the aileron and flap extension cord
into the wing half.
Using the adhesive tape to secure
the one end of the aileron and flap
extension cord in place.
Using the adhesive tape to secure the one
end of the aileron and flap extension cord in place.
X
30cm Extension cord
Thread
Aileron servo hatch
Turn the screws and full the aileron and
flap servo hatch out of the wing half.
Thread
Flap servo
hatch
Adhesive tape
WING TOP-VIEW
L/R
1.5mm
cut away only the covering
X
45
o
Flap servo
1-Aileron extension cord installation
Siai Marchetti SF-260
2- Flap servo installation
L/R
Flap pushrod
CA
Installing the flap servo on to the hatch (side-view)
Flap servo Hatch
Servo mount
Connector
WING BOTTOM
Pushrod exit hole
FLAP
3- Flap servo installation
Siai Marchetti SF-260
L/R
Plastic control horn
......2 set
............2
2mm
Connector
Flap push rod (2mm)
......2
.....2
Steel clevis
Bend the flap pushrod 35o at shown
35
90
o
Aileron servo
Installing the aileron servo on to the hatch (side-view)
Aileron servo Hatch
Servo mount
WING BOTTOM
AIL.
1.5mm
cut away only
the covering
X
4- Aileron servo installation
Siai Marchetti SF-260
L/R
Plastic control horn
............2 set
Aileron push rod (2mm)
......2
.....2
Steel clevis
.....2
EZ link
Aileron linkage
Steel Clevis
EZ link
Note: Do not glue the wooden
ring to the strut at this time.
5- Electric retract and Strut installation
Siai Marchetti SF-260
L/R
X
X
2
1
6- Electric retract and Strut installation
Siai Marchetti SF-260
L/R
CA
CA
Loading...