VQ Models HORNET EDF Instruction Manual
1.5mm
A
B
!
CA
L/R
Assemble left and right
sides the same way.
X
Drill holes using the stated
size of drill
(in this case 1.5 mm )
Use epoxy glue
Take particular care here
Hatched-in areas:
remove covering
film carefully
Not included.
These parts must be
purchased separately
Check during assembly that these
parts move freely, without binding
Apply cyano glue
CA
GLUE
Cyanoacrylate Glue (thin type)
Minimum 6 channels radio
Extension cord for aileron servos: 50cm(x2)
TOLLS REQUIRED
Hobby knife
Needle nose Pliers
Phillip screw driver
Awl
Scissors
Wire Cutters
(Purchase separately)
Hex Wrench
.........................................................
.........................................................
.........................................................
.........................................................
.........................................................
.........................................................
.........................................................
.........................................................
.........................................................
.........................................................
.........................................................
Sander
Masking tape - Straight Edged Ruler - Pen or pencil - Drill and Assorted Drill Bits
Read through the manual before you begin, so you will have an overall idea of what to do.
Symbols used throughout this instruction manual, comprise:
(Purchase separately)
CONVERSION TABLE
1.0mm = 3/64”
1.5mm = 1/16”
2.0mm = 5/64”
2.5mm = 3/32”
3.0mm = 1/8”
4.0mm = 5/32”
5.0mm = 13/64”
6.0mm = 15/64”
10mm = 13/32”
12mm = 15/32”
15mm = 19/32”
20mm = 51/64”
25mm = 1”
30mm = 1-3/16”
45mm = 1-51/64”
If exposed to direct sunlight and/or heat, wrinkels can appear. Storing the
model in a cool place will let the wrinkles disappear. Otherwise, remove
wrinkles in covering film with a hair dryer, starting with
low temperature. You can fix the corners by using a hot iron.
Bei Sonneneinstrahlung und/oder Wärme kann die Folie erschlaffen bzw. Falten
entstehen. Verwenden Sie ein Warumluftgebläse (Haartrockner) um evtl. Falten aus der Folie
zu bekommen. Die Kanten können Sie mit einem Bügeleisen behandeln. Nicht zuviel Hitze anwenden !
REQUIRED FOR OPERATION (Purchase separately)
Low seting
14.8v - 4500mAh LiPo battery
Extension cord for flap servos: 50cm(x4)
Extension cord for retract servos: 30cm(x2)
Extension cord for Rx battery pack: 20cm(x1)
EPOXY A
EPOXY B
Epoxy Glue
(30 minute type)
Mini Servo
Elevator : 1 mini servo
Aileron: 2 mini servo
Flaps: 2 mini servo
Nose gear: 1 mini servo
Hornet EDF
1
Instruction manual
7 Channels with option E-retract
EDF 70mm - 2750Kw
Hornet EDF
2
Instruction manual
wooden dowel
RIGHT
WRONG
Half wing panel - top view
Main landing gear
Gear mount
2
Ply gear mount
plate x 2
Gear mount x 2
3x20mm screw
..........8
3x12mm screw
......16
Nylon gear strap
.......4
Square plastic x 2
1
3x20mm
Nylon gear
strap
2mm
3x20mm
Ply gear
mount flat
Square
plastic
2mm
3 4
Main gear x 2
Nose gear
CA
CA
6mm dowel
......4
6mm dowel
6mm dowel
L/R
Assemble left and right
wings the same way.
1 Dowel installation
2 Fixed gear assemble
Hornet EDF
3
Instruction manual
3x12mm screw
.......8
2mm
2mm
X
L/R
Assemble left and right
wings the same way.
3 Fixed gear installation
4 E-retract installation
Hornet EDF
4
Instruction manual
4mm collar
.....4
X
Plastic control horn
......2
CA
CA
! Securely glue together. If coming off during fly,
you lose control of your air plane.
L/R
Assemble left and right
wings the same way.
L/R
Assemble left and right
wings the same way.
X
X
5 E-retract installation
6 Control horn installation
Loading...