VQ Model Beechcraft Baron, VQA157USAR, VQA157US Instruction Manual
SPECIFICATIONS
Wingspan:.........................1760mm (69.2in)
Length:.............................1210mm (47.6 in)
Electric Motor:.....................See next pager
Glow Engine:.................... Twin 40 - 2T
RTF Weight: 4.3Kg / 9.5lbs (Will vary with
Equipment Used).
Radio:......................6 Channel / 7-8 Servos
Function: Ailerons-Elevator-Rudder-Throttle
Flaps-Optional Retractable Landing Gear.
WARNING! This radio controlled model is NOT a toy. If modified or flown carelessly it could go out of controll and
cause serious human injury or property damage. Before flying your airplane, ensure the air field is spacious enough.
Always fly it outdoors in safe areas and seek professional advice if you are unexperienced.
ACHTUNG! Dieses ferngesteuerte Modell ist KEIN Spielzeug! Es ist für fortgeschrittene Modellflugpiloten bestimmt,
die ausreichende Erfahrung im Umgang mit derartigen Modellen besitzen. Bei unsachgemässer Verwendung kann
hoher Personen- und/oder Sachschaden entstehen. Fragen Sie in einem Modellbauverein in Ihrer Nähe um
professionelle Unterstätzung, wenn Sie Hilfe im Bau und Betrieb benötigen. Der Zusammenbau dieses Modells ist
durch die vielen Abbildungen selbsterklärend und ist für fortgeschrittene, erfahrene Modellbauer bestimmt.
Radio control model / Flugmodel
ALL BALSA, PLYWOOD CONSTRUCTION AND ALMOST READY TO FLY
BEECHCRAFT
Instruction manual / Montageanleitung
TECHNISCHE DATEN
Spannweite:...................................1760mm
Lange:............................................1210mm
Elektroantrieb.............(siehe nächste Seite)
Verbrennerantrieb:........................7.45cc 2T
Fluggewicht:.......................................4.3Kg
Fernsteuerung.............6 Kanal / 7-8 Servos
VQ No: VQA157USAR - VQA157US
BARON
1.5mm
A
B
!
CA
L/R
Assemble left and right
sides the same way.
X
Drill holes using the stated
size of drill
(in this case 1.5 mm ÿ)
Use epoxy glue
Take particular care here
Hatched-in areas:
remove covering
film carefully
Not included.
These parts must be
purchased separately
Check during assembly that these
parts move freely, without binding
Apply cyano glue
SILICON
EPOXY A
EPOXY B
CA
GLUE
Epoxy Glue ( 5 minute type)
Silicon sealer
Cyanoacrylate Glue
Minimum 6 channel radio
for airplane with 6 (7 for EP) servos.
.50 - 4 cycle
10.5x6 for .40 - 2 cycle engine
11x6 for .46 - 2 cycle engine
12x7 for electric motor
Silicone tube
Extension for aileron, Flap
servo, retract servo
and Rx battery pack.
.40 - 2 cycle
Epoxy Glue (30 minute type)
TOLLS REQUIRED
Hobby knife
Needle nose Pliers
Phillip screw driver
Awl
Scissors
Wire Cutters
(Purchase separately)
Hex Wrench
.........................................................
.........................................................
.........................................................
.........................................................
.........................................................
.........................................................
.........................................................
.........................................................
.........................................................
.........................................................
.........................................................
Sander
Masking tape - Straight Edged Ruler - Pen or pencil - Drill and Assorted Drill Bits
Read through the manual before you begin, so you will have an overall idea of what to do.
Symbols used throughout this instruction manual, comprise:
(Purchase separately)
.Motor control x1 mini servo(for GP) .Elevator x1
.Rudder x1. Aileron x2mini servo. Flapx2 mini servo
CONVERSION TABLE
1.0mm = 3/64”
1.5mm = 1/16”
2.0mm = 5/64”
2.5mm = 3/32”
3.0mm = 1/8”
4.0mm = 5/32”
5.0mm = 13/64”
6.0mm = 15/64”
10mm = 13/32”
12mm = 15/32”
15mm = 19/32”
20mm = 51/64”
25mm = 1”
30mm = 1-3/16”
45mm = 1-51/64”
If exposed to direct sunlight and/or heat, wrinkels can appear. Storing the
model in a cool place will let the wrinkles disappear. Otherwise, remove
wrinkles in covering film with a hair dryer, starting with
low temperature. You can fix the corners by using a hot iron.
Bei Sonneneinstrahlung und/oder Wärme kann die Folie erschlaffen bzw. Falten
entstehen. Verwenden Sie ein Warumluftgebläse (Haartrockner) um evtl. Falten aus der Folie
zu bekommen. Die Kanten können Sie mit einem Bügeleisen behandeln. Nicht zuviel Hitze anwenden !
REQUIRED FOR OPERATION (Purchase separately)
Low seting
800 Watt Brushless Motor
Do the same way with second
wing half.
Carefully, push the motor mount into the opening on
the wing until the line on the base matches the wing surface.
the line on the mount
INSTRUCTION MANUAL
BEECHCRAFT BARON 1
1- Motor mount installation
CA
Note: Remove the cover before gluing.
WING - TOP VIEW
WING - TOP VIEW
CA
CA
6mm dowel
Using a wooden motor mounting plate
as a template, mark the fire-wall where
the four holes are to be drilled.
Remove the wooden motor mounting
plate and drill a 5mm hole through
the fire-wall at each of the four marks
marked .
5x80mm bolt.....4
5mm nut..........12
5mm washer...16
Using a aluminum motor mounting plate
as a template, mark the plywood motor
mounting plate where the four holes are
to be drilled.
Remove the aluminum motor mounting
plate and drill a 1/8”(3mm) hole through
the plywood at each of the four marks
marked .
3mm
! Align the mark on wooden motor
mounting plate with the mark on
the fire-wall.
Triangles balsa
fill the Epoxy into the slit
BARON
UP
Do the same way with second
wing half.
Do the same way with second
wing half.
5mm
INSTRUCTION MANUAL
BEECHCRAFT BARON 2
A
B
A
B
2- Motor mount installation
3- Motor mount installation
Step 3A
Step 3B
Step 3C
Step 3D
Step 3E
1-Cut away the covering of the wing bottom
where the aileron servo goes.
2-Connect the aileron servo cord to the aileron
extension cord.
3-Install the aileron servo on the servo mount.
3mm bolt / nut...4
Secure the Motor to the wooden
motor mounting plate using the
four 3mm bolts.
B=B’
! Motor thrust on balk head
is already adjust at factory
B
105-110mm
B’
Motor and Motor base - Side view
105-110mm
105-110mm
Note:Engine mount and fuel tank must be purchased separately
Adhesive
tape
Do the same way with second
wing half.
Do the same way with second
wing half.
INSTRUCTION MANUAL
BEECHCRAFT BARON 3
4- Motor mount installation
5- Engine installation
6- Servo installation
1-Depending on the position of the linkage, determine the location of aileron control horn.
The horn holes must be perfectly aligned with the axis of articulation.
2-Mark the position of the “foot” of the horn on the aileron. Then, with the drill, make the 2
holes.
3-Install the aileron control horn as shown.
Plastic control horn
..........4
2x30mm screw
Control horn Alignment
..........8
..........2
2x175mm rod
Connector
EZ link
..........2
Steel Clevis
........2
...2
-Switch on the radio (trims centered)
then mount the ailerons servo horn
in neutral position.
-The servo horn should be
perpendicular to the servo
YES
NO
Do the same way with second
wing half.
Do the same way with second
wing half.
INSTRUCTION MANUAL
BEECHCRAFT BARON 4
7- Control horn installation
8- Linkages
Loading...