VQ Model VQA138SW, VQA138CA Building Instructions

Semi scale model
BUILDING INSTRUCTIONS / MONTAGEANLEITUNG
Specification: Wingspan 72.4 in. Length 54.1 in.(Canada version)
56.5 in. (Swiss version) Flying weight 7.5 lbs Motor See next pager Radio See next pager
Technische Daten: Spannweite 1.840mm Länge 1.375mm (Canada version)
1.435mm (Swiss version) Fluggewicht 3.400g Verbrennerantrieb Fernsteuerung
WARNING! This radio controlled model is NOT a toy. If modified or flown carelessly it could go out of controll and cause serious human injury or property damage. Before flying your airplane, ensure the air field is spacious enough. Always fly it outdoors in safe areas and seek professional advice if you are unexperienced.
ACHTUNG! Dieses ferngesteuerte Modell ist KEIN Spielzeug! Es ist für fortgeschrittene Modellflugpiloten bestimmt, die ausreichende Erfahrung im Umgang mit derartigen Modellen besitzen Bei unsachgemäßer Verwendung kann hoher Personen- und/oder Sachschaden entstehen. Fragen Sie in einem Modellbauverein in Ihrer Nähe um professionelle Unterstützung, wenn Sie Hilfe im Bau und Betrieb benötigen. Der Zusammenbau dieses Modells ist durch die vielen Abbildungen selbsterklärend und ist für fortgeschrittene, erfahrene Modellbauer bestimmt.
RADIO CONTROL MODEL / RC FLUGMODELL
DHC-6
VQA138SW
VQA138CA
# C8802 Fernsteuerung GigaProp 6
# C9493 Antriebsset Brushless f.
1.5mm
A
B
!
CA
L/R
Assemble left and right sides the same way.
X
Drill holes using the stated size of drill
(in this case 1.5 mm )
Use epoxy glue
Take particular care here
Hatched-in areas:
remove covering film carefully
Not included. These parts must be
purchased separately
Check during assembly that these
parts move freely, without binding
Apply cyano glue
CA
GLUE
Cyanoacrylate Glue (thin type)
# C8802 Fernsteuerung GigaProp 6
TOLLS REQUIRED
Hobby knife
Needle nose Pliers
Phillip screw driver
Awl
Scissors
Wire Cutters
(Purchase separately)
Hex Wrench
.........................................................
.........................................................
.........................................................
.........................................................
.........................................................
.........................................................
.........................................................
.........................................................
.........................................................
.........................................................
.........................................................
Sander
Masking tape - Straight Edged Ruler - Pen or pencil - Drill and Assorted Drill Bits
Read through the manual before you begin, so you will have an overall idea of what to do.
Symbols used throughout this instruction manual, comprise:
(Purchase separately)
CONVERSION TABLE
1.0mm = 3/64”
1.5mm = 1/16”
2.0mm = 5/64”
2.5mm = 3/32”
3.0mm = 1/8”
4.0mm = 5/32”
5.0mm = 13/64”
6.0mm = 15/64”
10mm = 13/32” 12mm = 15/32” 15mm = 19/32” 20mm = 51/64”
25mm = 1” 30mm = 1-3/16” 45mm = 1-51/64”
If exposed to direct sunlight and/or heat, wrinkels can appear. Storing the model in a cool place will let the wrinkles disappear. Otherwise, remove wrinkles in covering film with a hair dryer, starting with low temperature. You can fix the corners by using a hot iron.
Bei Sonneneinstrahlung und/oder Wärme kann die Folie erschlaffen bzw. Falten entstehen. Verwenden Sie ein Warumluftgebläse (Haartrockner) um evtl. Falten aus der Folie zu bekommen. Die Kanten können Sie mit einem Bügeleisen behandeln. Nicht zuviel Hitze anwenden !
Sonderzubehör (empfohlen) / Opional Accessories (recommended):
Low seting
EPOXY A
EPOXY B
# X3598-120
5-Min Epoxy
# X3572
Zoom CA
# C9493 Antriebsset Brushless f. Twin Otter
Brushless Power Set for Twin Otter
# C6788 LiPo Akku RED POWER 4500-11.1V
2x # C5185 MASTER SERVO S2112
Radio Set GigaProp 6
Schwimmer Set für Twin Otter
# C9278 gelb / yellow # C9278 weiss / white
Floats kit for Twin Otter
2x # C5638 MASTER SERVO S3012MG
Infos und Bezugsmöglichkeiten:
www.pichler-modellbau.de
Klebstoffe sind separat erhältlich (nicht im Lieferumfang)
2x # C1687 MASTER SERVO S4020
Cut away only the covering
WING
(Top side)
Carefully, push the Motor mounting onto the slot on the wing as shown.
!
CA
Using the thin CA glue
Check the mark on the motor mounting with the surface of the wing before glue.
!
B’
B
A
B=B’
A= 71-73mm
MOTOR MOUNT - SIDE VIEW
Wing
71-73mm
WING
(Top side)
1- Motor mount
3x35mm screw....4
3mm nut.........................12
3mm washer.....................8
1A
1B
1C
1E
1F
5mm
1mm
2x8mm self tapping screw
1mm
WING
(Bottom side)
WING
(Bottom side)
WING
(Top side)
2- Motor mount
2A
2B
2B
2C
2D
2x8mm self tapping screw
2x8mm self tapping screw
.....................28
Wing
2mm
Aileron and Flap servo
3mm set Screw
2 mm
Aileron and Flap pushrod
Plastic control horn
.....................2
Linkage Stopper set
..................2
2x175mm pushrod
......2
CA
Thin CA
CA
Thin CA
CA
Thin CA
CA
Thin CA
WING - BOTTOM VIEW
Note: The rectangular hole for the control horn installation is pre- cut at factory. Cut away only the covering.
Wooden dowel
3- Cowling
1mm
3A
3B
1mm
2x8mm self tapping screw
2x8mm self tapping screw
.....................4
4- Wing: servo
4mm nut
4x45mm screw
Aluminum landing gear
...2
4X45mm screw
4mm nut
............4
............6
4mm washer
2x8mm self tapping screw
1mm
1mm
2x8mm self tapping screw
.....................10
3x15mm screw
................4
5- Main landing gear
3x15mm screw
Turn the 4x20mm plastic bolt inside the fuselage and move the landing gear hatch.
4x20mm plastic bolt
5A 5B
5C
5D
5E
Slide the ABS landing gear cover onto the aluminum landing gear and secure it in place using 2x8mm self tapping screws.
6- Nose landing gear
3x20mm screw
Attach the nose gear mount onto the fire-wall and secure it in place using four 3x20mm screws.
Route the steering linkage into the fuselage and through the fire-wall.
Insert “Z” bend of steering linkage into the hole of steering arm.
Glue the outer tube in place as shown.
CA
Slide the nose landing gear through the nose gear mount and steering arm with the flat to front. Tighten the screw of the steering arm to the nose landing gear.
Flat
6B
6A
6C
6D
Attach the fiberglass dome to the fuselage and secure it in place using 2x8mm self tapping screws.
Nose gear mount
3x20mm screw...4
Steering arm...1
..............1
4mm collar
..........2
2x8mm self tapping screw
..........5
6E
1mm
1mm
7- Stabilizer
Slowly, slide the horizontal stabilizer through the vertical stabilizer.
7A
When you are satisfied with the alignment, use a pencil to trace around the top and bottom of the horizontal stabilizer where it meets the vertical stabilizer. Remove the horizontal stabilizer.
7B
Check the alignment of the horizontal stabilizer, the distance must be equal on both sides (A=A’).
Vertical stabilizer
Horizontal stabilizer
A
A’
TOP VIEW
Cut away only the covering both sides.
Remove the horizontal stabilizer from the vertical stabilizer. Using a straight edge and a sharp hobby knife, carefully cut away the covering inside the lines which were marked above. Be cautious not to cut into the wood-this will weaken the structure.
7C
8- Stabilizer Continued
Again, slide the horizontal stabilizer through the vertical stabilizer.
With the perpendicular, check the alignment of the vertical stabilizer and the horizontal stabilizer during glue.
8A
CA
Thin CA
Horizontal stabilizer
Vertical stabilizer
Perpendicular
CA
CA
Slide the horizontal stabilizer holder onto the horizontal stabilizer as shown.
Horizontal stabilizer holder
When you are satisfied with the alignment, use a pencil to trace around the top and bottom of the horizontal stabilizer holder where it meets the vertical stabilizer. Remove the holder from the horizontal stabilizer.
Thin CA
Thin CA
8B
8C
8D
! Securely glue together. If coming off during fly, you lose control of your air plane.
Laser cut carton template
Aluminum tube
Horizontal stabilizer
Laser cut carton template
Using a sharp hobby knife, carefully cut away
the covering inside the lines which were marked above. Be cautious not to cut into the wood-this will weaken the structure.
Cut away only the covering and inside
the line
Again, slide the holder onto the horizontal stabilizer Apply the thin CA glue on the vertical stabilizer
where it contacts the holder.
Apply the thin CA glue on the horizontal stabilizer where it contacts the holder.
CA
CA
Thin CA
Thin CA
9- Stabilizer Continued
9A
9B
9C
Carefully, insert the vertical stabilizer into the slot on the fuselage as shown.
Check the incidence angle of the horizontal stabilizer using the laser cut carton template
- Slide the aluminum tube through the fuselage.
- Slide the left and right carton template through the aluminum tube and the horizontal stabilizer as shown (see pic. 9D)
Left carton template
Right carton template
Aluminum tube
Horizontal stabilizer
9D
A A’
Aluminum tube
Horizontal stabilizer
When you are satisfied with the alignment, use a sharp hobby knife, carefully cut the covering where the vertical stabilizer meet the fuselage. Be cautious not to cut into the wood - this will weaken the structure.
Carton template
Carton template
Remove the vertical stabilizer from the fuselage and cut away the covering on the vertical stabilizer as shown.
Again, insert the vertical stabilizer into the slot on the fuselage. When you are satisfied with the alignment (Step 10A), glue the vertical stabilizer where it meets the fuselage.
CA
Thin CA
A=A’
! Securely glue together. If coming off during fly, you lose control of your air plane.
10- Stabilizer Continued
10A
10B
10C
11- Rudder and Elevator
Cut away only the covering
CA
Apply thin CA glue on the top of the hinge
Apply a thin layer of petroleum jelly
HORIZONTAL STABILIZER
HORIZONTAL STABILIZER
TOP-SIDE
TOP-SIDE
Note: The rectangular holes are pre-laser cut at factory
Cut away only the covering
Do the same way with bottom side
! Securely glue together. If coming off during fly, you lose control of your air plane.
CA
Thin CA
CA
Thin CA
11A
11B
11C
11D
! Securely glue together. If coming off during fly, you lose control of your air plane.
12- Wing installation
Slowly, push the aluminum tube through the fuselage.
Carefully, push the wing to the fuselage as shown.
12A
12B
Note: Push the top hatch to the side of the fuselage and full it to remove.
CA
Nylon pushrod guide
Nylon pushrod guide
To rudder control horn
To left elevator control horn
To right elevator control horn
To nose gear arm
Connector
Connector
....1
....2
13- Wing installation
When the wing meet the fuselage with no gap, secure the wing in place using the 4x25mm plastic bolt.
4x25mm plastic bolt
2 mm
Rudder push-rod
FUSELAGE - TOP VIEW
.............................1
1.2x500mm rod
950mm long
...3
14- Servo and Linkages
Elevator push-rod
Elevator push-rod
2x120mm
.............................1
805 805
D
A
N
G
E
R
D
A
N
G
E
R
Note: Cut out the stickers and apply them in the proper area. Do not peel the backing paper off all at once. Peel off one corner of the backing and cut off with scissors. Arrange sticker on model and when satisfied adhere the corner without backing. Carefully peel back the rest of the backing while at the same time adhering the rest of the sticker. Try not to make air bubbles, if there are some, carefully puncture sticker (center of bubble) but not model surface with the tip of the knife or sharp pin and squeeze out the air. At curves stretch sticker and apply a little heat so that no ceases occur. Cut off the excess that is produced.
Decal of Otter Canada version
Decal of Otter Swiss version
Decal application: See the label on top box
15- Decal
2x8mm self tapping screw
...........4
3x15mm screw
.........2
3x12mm self tapping screw
...........2
3mm blind nut
...........2
15- Shield and Wing brace
1mm
2mm
The rectangular hole on the fuselage is pre-laser cut at factory. Cut away only the covering.
56 ~ 60mm
25mm
Aileron
Rudder
12mm
Querruderausschlag
Seitenruderausschlag
Do not try to fly an out-of balance model!
Uberprufen Sie vor dem Flug den Schwerpunkt.
15mm
15mm
Elevator
Hohenruderausschlag
Flap
18mm
All details are subject to change without notice !
Technische Anderungen und Irrtumer vorbehalten !
IMPORTANT:
Please do not clean your model with pure alcohol, only use liquid soap with water or use glass cleaner to clean on surface of your model to keep the colour not fade.
25mm
12mm
Adjust the travel of the control surfaces to achieve the values stated in the diagrams. These value will be suitable for average flight requirements. Adjust the values to suit your particular needs.
16- Control Surface
Loading...