VQ Model VQA037Y, VQA0371, VQA036W, VQA0361 Instruction Manual
PILATUS PORTER
PC-6
MONTAGEANLEITUNG
VQA0371
INSTRUCTION MANUAL
VQA037Y
VQA036W
SPECIFICATIONS
Wingspan 1580mm
Length 1160mm
Electric Motor 870 Watt (PULSAR 60)
Glow Engine .46 2-T / .70 4-T
Radio 5 Channel / 5 Servos
WARNING! This radio controlled model is NOT a toy. If modified or flown carelessly it could go out of controll and
cause serious human injury or property damage. Before flying your airplane, ensure the air field is spacious enough.
Always fly it outdoors in safe areas and seek professional advice if you are unexperienced.
ACHTUNG! Dieses ferngesteuerte Modell ist KEIN Spielzeug! Es ist für fortgeschrittene Modellflugpiloten bestimmt,
die ausreichende Erfahrung im Umgang mit derartigen Modellen besitzen Bei unsachgemäßer Verwendung kann
hoher Personen- und/oder Sachschaden entstehen. Fragen Sie in einem Modellbauverein in Ihrer Nähe um
professionelle Unterstützung, wenn Sie Hilfe im Bau und Betrieb benötigen. Der Zusammenbau dieses Modells ist
durch die vielen Abbildungen selbsterklärend und ist für fortgeschrittene, erfahrene Modellbauer bestimmt.
TECHNISCHE DATEN
Spannweiter 1580mm
Lange 1160mm
Elektroantrieb 870 Watt (PULSAR 60)
Verbrennerantrieb 7.5cc 2-T / 11cc 4-T
Fernsteuerung 5 Kanal / 5 Servos
VQA0361
46 Class
52 Class
(2T engine)
(4T engine)
Or Electric equivalent
Radio control model / R/C Flugmodel
.........................................................
.........................................................
.........................................................
.........................................................
.........................................................
.........................................................
.........................................................
.........................................................
.........................................................
.........................................................
.........................................................
1.5mm
A
B
!
CA
L/R
Assemble left and right
sides the same way.
X
Drill holes using the stated
size of drill
(in this case 1.5 mm Ø)
Use epoxy glue
Take particular care here
Hatched-in areas:
remove covering
film carefully
Not included.
These parts must be
purchased separately
Check during assembly that these
parts move freely, without binding
Apply cyano glue
SILICON
EPOXY A
EPOXY B
CA
Epoxy Glue (30 minutes type)
Silicon Glue
Cyanoacrylate Glue
Sekundenkleber
Epoxy-Klebstoff (30min)
Minimum 5 channel radio
for airplane
.52 cu.in (8.5cc)
Extension cord
.46 cu.in. (7.5cc)
REQUIRED FOR OPERATION (Purchase separately)
Minimum 5 Kanal
Fernsteuerung
Servoverlangerungskabel
BENOTIGTE KOMPONENTEN (Nicht im Lieferumfang enthalten)
Propeller 11x8 for electric motor / 11x6 for glow engine
Luftschraube 11x8 fur Elektromotor / 11x6 fur Verbrennungsmotor
Brushless Motor
PICHLER BOOST 40
Brushless ESC
Brushless Regler
Battery / Flugakku LEMONRC 3700-11.1V
Silikonkleber
Tool Required/ Erfoderliches Werkzeug
The pre-covered film on ARF kit may wrinkle due to variations of temperature.
Store model in a cool and dry place for awile.
Then, staring with low heat, you may carefully use a hair dryer to smooth out wrinkels.
Die Bespannung des Modells kann durch Temeratureinflusse erschlaffen oder Falten
werfen z.b bei zu starker Sonnenenstrahlung oder Hitze.
Stellen Sie das Modell zunachst an einen kuhlen Platz fur eine bestimmte Zeit. Danach
konnen Sie versuchen die restlichen Falten vorstichtig mit einem Haartrockner zu behandeln.
!
CONVERSION TABLE
1.0mm = 3/64”
1.5mm = 1/16”
2.0mm = 5/64”
2.5mm = 3/32”
3.0mm = 1/8”
4.0mm = 5/32”
5.0mm = 13/64”
6.0mm = 15/64”
10mm = 13/32”
12mm = 15/32”
15mm = 19/32”
20mm = 51/64”
25mm = 1”
30mm = 1-3/16”
45mm = 1-51/64”
WARNING!: Securely glue together, if coming of
during flights, you lose control of your plane
which lead to accidents.
1-Trial fit each part before gluing . Be certain
that there are no gaps. If the parts will join,
but with a gaps, sand or trim the parts a little
at a time until the parts meet exactly with no
gaps.
2-Check for the correct dihedral angle
3-When joining the wing halves it is extremely
important to use plenty of epoxy (30 minutes
epoxy).
1- Wing Joiner / Flachenverbinder
A
B
A
B
A
B
6mm plywood
3mm plywood brace
6mm plywood brace
TOP VIEW / Draufsicht
Trial fit each part before gluing . Be certain
that there are no gaps. If the parts will join,
but with a gaps, sand or trim the parts a little
at a time until the parts meet exactly with no
gaps.
WARNING!: Securely glue together, if coming of
during flights, you lose control of your plane
which lead to accidents.
A
B
7mm diameter wooden dowel
A = 10mm
WARNING!: Securely glue together, if coming of
during flights, you lose control of your plane
which lead to accidents.
Tragflächenverbinder
Tragflächenverbinder
Tragflächenverbinder
2- Wing Joiner
/ Flächenverbinder
3- Wing Joiner
/ Flächenverbinder
TOP VIEW / Draufsicht
Die Teile probehalber zusammenstecken
und ggf. Etwas nacharbeiten.
Fuhren Sie die Verklebungen mit gro ter
Sorgfalt aus
TOP VIEW / Draufsicht
Fuhren Sie die Verklebungen mit gro ter
Sorgfalt aus
WARNING: Securely glue together, if coming of
during flights, you lose control of your plane
which lead to accidents.
1-Trial fit each part before gluing . Be certain
that there are no gaps. If the parts will join,
but with a gaps, sand or trim the parts a little
at a time until the parts meet exactly with no
gaps.
2-Check for the correct dihedral angle
4-Carefully slide the wing halves together,
ensuring that they are accurately aligned,
Firmly press the two halves together, allowing
the excess epoxy run out
3-When joining the wing halves it is extremely
important to use plenty of epoxy (30 minutes
epoxy).
A
B
L/R
Plastic control horn
2x20mm screw
Linkage Stopper set
............................2
......................4
.....................2
A
B
To aileron extension cord
X
A
B
A
B
X
2mm
2x20mm screw
4- Joining the wing
5- Installing the linkages / Einbau RC-Anlage
/ Fläche
Gestängeanschluss
Die Teile probehalber zusammenstecken
und ggf. etwas nacharbeiten.
Fuhren Sie die Verkiebungen mit gro ter
Sorgfalt aus.
1.2mm O Alenk-Gestange
BOTTOM - VIEW / Unteransicht
BOTTOM - VIEW / Unteransicht
Cut here for standard servo
IMPORTANT:
Please do not clean off the excess epoxy on the wing with strong solvent
or pure alcohol, only use kerosene to keep the colour of your model not fade.
A
B
5mm
!
Align the engine center with fire-wall
marked line (A=A’)
Align the mark on both
mounts with the center
mark on the fire-wall
A
A’
FRONT VIEW
FRONT VIEW
In case of 4T engine
Using the four 3x20mm
screws securing the engine
to the engine-mount
B
B=107~110mm
4x25mm screw
Schraube
4mm
............4
.....................4
4x15mm screw
Blind-nut
............4
3x20mm screw
.....................4
3mm nut
3mm washer
.....................4
4mm washer
.....................4
6- Engine - Engine mount /
Motorträger - Motoreinbau
Motorträger
Pull the transparent sticker
to open the hatch.
Loading...