Wing span approx : 99.2 in.
Length approx : 44.0 in.
Radio: 4Channel / 4 servos
INSTRUCTION MANUAL / MONTAGEANLEITUNG
SPECIFICATION
TECHNISCHE DATEN
Spannweite : 2520mm
Lange : 1120mm
Fernsteuerung: 4 Kanal / 4 servo
Electric Powered Glider
R/C Motorsegler
ARF BY
WARNING! This radio controlled model is NOT a toy. If modified or flown carelessly it could go out of controll and
cause serious human injury or property damage. Before flying your airplane, ensure the air field is spacious enough.
Always fly it outdoors in safe areas and seek professional advice if you are unexperienced.
ACHTUNG! Dieses ferngesteuerte Modell ist KEIN Spielzeug! Es ist für fortgeschrittene Modellflugpiloten bestimmt,
die ausreichende Erfahrung im Umgang mit derartigen Modellen besitzen Bei unsachgemäßer Verwendung kann
hoher Personen- und/oder Sachschaden entstehen. Fragen Sie in einem Modellbauverein in Ihrer Nähe um
professionelle Unterstützung, wenn Sie Hilfe im Bau und Betrieb benötigen. Der Zusammenbau dieses Modells ist
durch die vielen Abbildungen selbsterklärend und ist für fortgeschrittene, erfahrene Modellbauer bestimmt.
.........................................................
.........................................................
.........................................................
.........................................................
.........................................................
.........................................................
.........................................................
.........................................................
.........................................................
.........................................................
.........................................................
1.5mm
A
B
!
CA
L/R
Assemble left and right
sides the same way.
X
Drill holes using the stated
size of drill
(in this case 1.5 mm Ø)
Use epoxy glue
Take particular care here
Hatched-in areas:
remove covering
film carefully
Not included.
These parts must be
purchased separately
Check during assembly that these
parts move freely, without binding
Apply cyano glue
SILICON
EPOXY A
EPOXY B
CA
Epoxy Glue (30 minutes type)
Silicon Glue
Cyanoacrylate Glue
Sekundenkleber
Epoxy-Klebstoff (30min)
Minimum 4 channel radio
for airplane
Extension cord
REQUIRED FOR OPERATION (Purchase separately)
Minimum 4 Kanal
Fernsteuerung
Servoverlangerungskabel
BENOTIGTE KOMPONENTEN (Nicht im Lieferumfang enthalten)
PULSAR 40
# C6217
Battery / Flugakku
# C2141 LEMONRC 3700-11.1V
Silikonkleber
Tool Required/ Erfoderliches Werkzeug
The pre-covered film on ARF kit may wrinkle due to variations of temperature.
Store model in a cool and dry place for awile.
Then, staring with low heat, you may carefully use a hair dryer to smooth out wrinkels.
Die Bespannung des Modells kann durch Temeratureinflusse erschlaffen oder Falten
werfen z.b bei zu starker Sonnenenstrahlung oder Hitze.
Stellen Sie das Modell zunachst an einen kuhlen Platz fur eine bestimmte Zeit. Danach
konnen Sie versuchen die restlichen Falten vorstichtig mit einem Haartrockner zu behandeln.
!
CONVERSION TABLE
1.0mm = 3/64”
1.5mm = 1/16”
2.0mm = 5/64”
2.5mm = 3/32”
3.0mm = 1/8”
4.0mm = 5/32”
5.0mm = 13/64”
6.0mm = 15/64”
10mm = 13/32”
12mm = 15/32”
15mm = 19/32”
20mm = 51/64”
25mm = 1”
30mm = 1-3/16”
45mm = 1-51/64”
Klappluftschraube
13x8 Best.Nr C7127
Mini servo DS3012
# C49955
Regler: PULSAR A-50
# C6130
ECO Adapter 5.0mm
Best.Nr. C6062
Attach the Horizontal Stabilizer
Incorrect
Correct
A
A’
A=A’
A
A’
A=A’
/
Check the alignment of the horizontal
stabilizer by measuring from a fixed point
along the center line of the fuselage to the
leading edge on each side of the horizontal
stabilizer. The distance must be equal on
both sides. If not, adjust the stabilizer until
the measurements are the same.
Securely glue together. If coming
off during flight, you lose control
of your air plane.
4x30mm nylon bolt
............1
Control horn
...........1
1A
TOP VIEW
Draufsicht
CA
CA
Thin CA
1.5mm
Using a pencil, mark on the leading edge of elevator,
where the hole is to be drilled.
Drill a 1.5mm hole of the mark made in Step 1D
Marking sure that you drill the hole
perpendicular to the leading edge
of the elevator half.
MARK
1
1B
1C
1D
1E
1F
Trial fit the elevator half in place, check the alignment
of the horizontal stabilizer and the elevator half.
Fuhren Sie die Verklebungen mit gro ter
Sorgfalt aus.
A
B
CA
Tail gear
BOTTOM - VIEW
Unteransicht
Cut away only
the covering
2A
Insert the Z bend into the control horn.
Push the foot of control horn into the slot
on the elevator as shown.
Slide the elevator push-rod (in the hard-ware bag)
into the white nylon push-rod guider.
White nylon push-rod
guider
CA
Thin CA
Securely glue together. If coming
off during flight, you lose control
of your air plane.
Fuhren Sie die Verklebungen mit gro ter
Sorgfalt aus.
Attach the Vertical Stabilizer
Incorrect
Correct
Check the alignment of the vertical
stabilizer.The distance must be equal on
both sides. If not, adjust the stabilizer until
the measurements are the same.
A
A’
A=A’
A
A’
A=A’
2
2B
2C
2A
2B
2C
2D
2D
Secure the control horn in place using
thin CA glue.
2E
2F
1.2x900mm rod.............2
CA
Cut away
the covering
Thin CA
Control horn
...........1
4x50mm screw
4x50mm screw
........1
........2
........2
........1
X
Elevator servo
Höhenruderservo
Rudder servo
Seitenruderservo
TOP VIEW
Draufsicht
Linkage Stopper set
..............2
Gestängeanschluss
4x40mm screw
4mm washer
4mm washer
4mm nut
BOTTOM - VIEW
Unteransicht
CA
3
CA
Insert the Z bend into the control
horn.
Push the foot of control horn
into the slot on the rudder
as shown.
Slide the rudder push-rod (in the
hard-ware bag)into the white nylon
push-rod guider.
3A
3B
3C
3A
3B
3C
3D
3D
4
5
Aileron servo
hatch (ply 3mm)
Linkage Stopper set
..............2
Gestängeanschluss
Aileron servo
hatch (ply 3mm)
Cut away
the covering
CA
Thin CA
Magnetic canopy
hatch
Aluminum wing joiner
2.5x10mm screw
............4
6
Control horn...2
BOTTOM - VIEW
Unteransicht
Fuhren Sie die Verklebungen mit gro ter
Sorgfalt aus.
7
TOP VIEW
Draufsicht
Aluminum wing joiner
4X20mm
A
B
5 min. Epoxy
L/R
20x6mm woden dowel.
A
B
TOP VIEW
Draufsicht
4x20mm screw
.....2
6x20mm wooden dowel
.....4
RIGHT WING HALVE
WING HALVES INSTALLATION
1- Pull the magnetic top hatch out of the fuselage.
2- Carefully slide the wing halve to the fuselage
as shown (Right picture), ensuring that the wing
halve accurately aligned.
3- Carefully slide the second wing halve to the
fuselage. Firmly press the two halves together.
4- Secure the wing halves in place using two
4x20mm screw
8
CG
WARNING ! Securely install the receiver and power pack, ensuring they will not come loose or rattle during flight.
Never fly before checking the Cg’s required position.
Do not try to fly an out-of balance model!
Uberprufen Sie vor dem Flug den Schwerpunkt.
68 ~ 72mm
Note: If necessary, move the battery pack or add weight to either
the tail or nose until the correct balance is achieved.
1-23/64”(30 mm)
15/64”(6mm)
13/32”(10mm)
15/64”(6mm)
13/32”(10mm)
1-23/64”(30 mm)
RUDDER / SEITENRUDER
AILERON / QUERRUDER
ELEVATOR / HOHENRUDER
All details are subject to change
without notice !
Technische Anderungen und Irrtumer
vorbehalten !
9
10
Loading...