VPC i2 MX Series, i2 MX 310 130 Series, i2 MX 410 130 Series User Manual
i2 MX USER’S MANUAL: SECTION 7 VIRGINIA PANEL CORPORATION
i2 MX MODULE INSERT(S) INSTALLATION/REMOVAL
PART # 310 130 XXX AND 410 130 XXX
TOOLS REQUIRED
Phillips Head Screwdriver
i2 MX MODULE INSERT(S) REMOVAL INSTRUCTIONS
1. If working with a receiver, use a Phillips head screwdriver to remove
strain relief by removing screws (Figure A).
The ITA will require removal of backshell rst see Section 4 of this User’s
Manual.
2. Using a Phillips head screwdriver, remove the two Phillips at head
screws that are holding the frame halves together.
For ITA use a Phillips head screwdriver to loosen the two captive screws
on the back of rear frame (Figure B).
3. Pull halves apart.
4. Remove module insert(s).
i2 MX MODULE INSERT(S) INSTALLATION INSTRUCTIONS
1. For installing module insert(s), orient insert(s) as shown in (Figure A) and
(Figure C). Place insert(s) ledge on at surface shown in (Figure D), then
put halves together and tighten with at head screws using a Phillips
head screwdriver.
NOTE: Receiver/ITA frame halves are keyed to be placed together only one
direction.
PHILLIPS
FLAT HEAD
SCREWS (2)
Figure A. Module insert install and removal
(receiver shown).
PHILLIPS
CAPTIVE
SCREWS (2)
ITA PIN A1
UPPER RIGHT
Figure B. ITA frame separation.
RECEIVER PIN
A1 UPPER LEFT
Figure C. Module insert install and removal
(receiver shown).
Figure D. Module insert install and removal
(receiver shown).
7-1 For the most current information available, visit www.vpc.com
FLAT SURFACE
2/5/16
i2 MX USER’S MANUAL: SECTION 7 VIRGINIA PANEL CORPORATION
VTAC HSD RAIL(S) INSTALLATION/REMOVAL INSTRUCTIONS
PART # 310 130 XXX AND 410 130 XXX
TOOLS REQUIRED
Phillips Head Screwdriver
VTAC HSD RAIL(S) REMOVAL INSTRUCTIONS
1. If working with a receiver, use a Phillips head screwdriver to
remove strain relief by removing screws (Figure A).
The ITA will require removal of backshell rst. See Section 2 of this
User’s Manual for instructions.
2. After removing strain relief/backshell, use a Phillips head
screwdriver to remove the two Phillips at head screws that are
holding the frame halves together (Figure A).
For ITA use Phillips head screwdriver to loosen the two captive
screws on the back of the rear frame (Figure B).
3. Pull halves apart.
4. Remove VTAC HSD Rail(s).
VTAC HSD RAIL(S) INSTALLATION INSTRUCTIONS
1. To install VTAC HSD Rail(s), orient rail(s) as shown in (Figure A).
Figure C illustrates the identiers to aid in orientation (receiver rails
shown). The receiver rails are marked with ‘RR’ (receiver right) and
‘RL’ (receiver left) when viewing from mating face. The ITA rails
are marked with ‘IR’ (ITA right) and ‘IL’ (ITA left) when viewing from
rear/wiring side.
2. Place rail(s) ledge on at surface shown in (Figure D), then put
halves together and tighten the two Phillips at head screws using
a Phillips head screwdriver.
NOTE: Receiver/ITA frame halves are keyed to be placed together
only one direction.
PHILLIPS
FLAT HEAD
SCREWS (2)
TOP OF
RAIL
Figure A. VTAC HSD Rail(s) install/removal (receiver shown).
PHILLIPS
CAPTIVE
SCREWS (2)
Figure B. ITA frame separation.
‘RL’ RECEIVER
LEFT
Figure C. VTAC HSD Rail(s) - Identiers.
BLACK PIN AI
INDI CATOR
‘RR’ RECEIVER
RIGHT
TOP
BOTTOM
Figure D. VTAC HSD Rail(s) install/removal
(receiver shown).
7-2 For the most current information available, visit www.vpc.com
FLAT SURFACE
2/5/16
Loading...