Voxx Electronics SRT-9000 Owner's Manual
MODEL SRT-9000
REMOTE ENGINE STARTER
WITH ALARM SYSTEM
OWNER’S MANUAL
1
OLED REMOTE TRANSCEIVER
A. OLED DISPLAY…………………………………………………………………………………………………………………… 4
Reset the Remote Transceiver
B.
CHARGE THE BATTERY ……….…………………………………………………………………………….……..…….. 4
C. MAIN PAGE ……………………………………………………………………………………………………….…………… 5
D. SELECT THE TRANSCEIVER’S BUTTON CONFIGURATION ……………………………………….…………. 6
E. SELECT THE TRANSCEIVER FEATURES …………………………………………..……………….………………. 6
P1-1: Enable / Disable Bi Sound While Pressing Button (7)
P1-2: Button Lock Setting (7)
P1-3: Melody / Vibration Mode (7)
P1-4: Demo Mode (8)
P2-1: Power Save Mode (8)
P2-2: Parking Meter Setting (8)
P2-3: Parking Area Setting (8)
P2-4: “Light For OLED” Timer Setting (9)
P3-1: Timer Setting (9)
P3-2: Alert Alarm Timer Setting (9)
P3-3: Count Down Timer Setting (10)
P3-4: Daily Start Timer Setting (10)
P4-1: Name of
Transceiver Setting (11)
P5-1: Name of Channel Setting (11)
P6-1: Language Setting (11)
P6-4: Set To Defaults (12)
TABLE OF CONTENTS
A. REMOTE TRANSMITTER OPERATION ……………………………………………….………………….………….….… 12
B. LED DISPLAY .……………..………………………………………………………….………………….…………………… 12
C. CHIRP INDICATOR ..………..……………………………………………………………………..……………….…..……. 12
D. PARKING LIGHT …….……..…………………………………………………………………………………..……….….…. 12
E. ACTIVE ARMING – ARM & LOCK .……………………………………………………………………………….…………. 13
Ajar Warning
Silent Arming
Sensor By-Pass
Hidden Alarm Mode
F. PASSIVE ARMING .…………………………………………..…………………………...………………………….….…… 13
Passive Arming with Passive Door Locking
Passive Arming By-Pass
G. ACTIVE DISARMING – UNLOCK & DISARM .……………………………………….………………..…………………. 13
Silent Disarming
Tamper Disarming
Pathway Illumination
Two Steps Door Unlock
Automatic Re-Arm
H. DISARMING WITHOUT A TRANSMITTER .……………..………………………………………………………..…….... 14
Overrides the Alarm without Password Pin Code
Overrides the Alarm With Password Pin Code
I. VALET MODE .……………..………………………………………………………………………….…………………..…... 14
J. CAR LOCATOR .……………………………………………………………………………….……………………………...… 15
K. PANIC FUNCTION .…………………………………………………………………………………...….……………….….. 15
L. TRIGGER THE SYSTEM .………………………………………..………………………..……………….………….…….. 15
Stop The Melody Sound
Noise Abatement Circuit
M. ANTI CAR- JACKING .…………………………………………………………………………..…………………….…….. 16
N. SYSTEM’S TRIGGER CHECK ………………………………………………………………………..….…………....……. 16
O. SYSTEM’S STATUS CHECK ……………………………………………………………..…………….……………..……. 16
P. DRIVER PAGING / LOSE AND FOUND ………………………….…………..……………………..…...………………... 16
Q. DOME LIGHT CONVENIENCE DELAY & SUPERVISION ……………………..………..…………….………..…….... 17
R. IGNITION CONTROL THE DOOR LOCK/UNLOCK. ………..………………….…………….…….……………..…..…. 17
S. TRUNK RELEASE (CHANNEL 3) OUTPUT ………..…………………………………………………...……………..…. 17
T. AUX1/2/3/4 TIMER CONTROL OUTPUT ………..…………………………………………………………….….……….. 17
U. MULTI-VEHICLE SECURITY OPREATION …………..…………………………………………………………….…….… 17
V. POWER ON MEMONRY ………….……………………………………………………………….…….…………………….. 18
2
REMOTE START OPERATION
A. TO REMOTE START THE VEHICLE ………..………………………………………..………………………..………….. 18
B. TO OPERATE THE VEHICLE WHILE RUNNING ON THE REMOTE START ……………..……………………..….. 18
C. TEMPORARY STOP FEATURE ……………………………………………….……………………….…………………… 18
D. TURBO TIMER MODE ……………………..………………………………….……………….……………...………..….… 18
E. TIMER START …………………………………………….…………….………………………………..…………………… 19
3 (2 or 1) Hours Timer Start
Daily Timer Start
Cancel the Timer Start
F. TEMPERATURE CHECK ……………….……………………………………………..…….…...……….…………….….… 19
G. TO TURN OFF THE REMOTE START …………………………………………………….….…….………………….….…19
H. SHUT-DOWN INPUT FOR REMOTE STARTER …………..…………………….……………………………..….……… 19
I. DISABLING THE REMOTE START SYSTEM ………………………………….……………………..……………….….… 20
TEST MODE …………………..…………….………………………………..………………….…...……….………..…….…… 20
SHUTDOWN DIAGNOSTICS …………….……………………………………..…………….…...……….………..….….…… 20
WARNINGS:
As with any product that performs automatic functions, there are certain safety precautions that you must
practice and be aware of.
1. Keep the transmitter out of children’s reach.
2. Do not leave anyone in the vehicle while running on remote control.
3. Alert servicing personnel that the vehicle can be started automatically.
4. Do not start the vehicle by remote while it’s in an enclosed area or garage.
5. Always apply the parking brake and lock the vehicle as you exit the vehicle.
6. The vehicle windows must be rolled up.
7. Should the unit malfunction, disconnect the fuse until the problem is corrected.
8. The use and operations of this system is the sole responsibility of the operator.
9. Some areas may have local ordinances that prohibit leaving a vehicle running on public streets.
10. Do not start the vehicle by remote while the standard transmission vehicle is parked at a steep place.
3
REMOTE TRANSCEIVER (TX)
A. OLED DISPLAY
Name of Transmitter
Timer
Door Lock
Door Unlock
In – Range Indicator
Alarm Status
Temperature
Car jacking
Battery Level
Engine Running
Melody Mode
Count Down Timer
Parking Timer
Vibration Mode
Alert Alarm
Timer Start
switch
switch
button
Level and
p
ush switch
開關
側視
圖
switch
Button
Button
2
Button
Button
4
switch
button
Level and
p
ush switch
A
ntenna
OLED Display OLED Display
Button
Button
1
Button
Button 3
Reset Hole
4
Power by built-in 3.7V lithium polymer battery, if the OLED screen
display low battery or
is flash, charge your remote
transceiver. While the battery of the Remote Transceiver is under
the battery charging, you can push the ”
” button to check
charging condition.
Optional AC Power Supply
If you have optional AC POWER SUPPLY / AC ADAPTOR (Output
Voltage: 4.2VDC – 5.5VDC and with same USB plug), then you can charge
the battery indoors.
While the battery of
the Remote
Transceiver is under
charging.
Push the button; the
screen will display
Battery charging.
Charge Input
USB Input
C. MAIN PAGE:
1. Press the
button, the screen will display main page.
2. While the icon flashing on the OLED screen, press the
button, the OLED screen will display the
detail of the flash icon, the display sequence of flash icon as follows: TRIGGERED / ENGINE
RUNNING / COUNT DOWN TIMER / TIMER START / ALART TIMER condition.
While the
TRIGGERED icon
flash.
Push the
button to display
triggered area.
.
While the icon flash
Push the button
5
While the icon
flash
Push the button, the count
down timer will display.
Press the button 2 to set off
the count down time
or
or
While the icon flash
Push the button, the OLED screen will display individually i.e. daily start timer, timer
start or temperature start, depend on which you selected.
While the
icon
flash
Push the button, the alert
alarm time will display.
Press the button 2 to set off
the alert alarm timer
D. SELECT THE TRANSCEIVER’S BUTTON CONFIGURATION:
1. Spin up the
Switch to select the transceiver button configuration you need and the OLED screen
will display the transceiver button configuration you select.
2. Within 5 seconds press the button 1, 2, 3 or 4 to remote control “button configuration” you selected.
Note: If 5 seconds of inactivity expired, or push the
button, the transceiver button configuration mode
will exit.
Spin up the switch
To the page 1
Spin up the switch
to the page 2
Spin up the switch
To the page 3
Spin up the switch
to the page 4
Spin up the switch
to the page 5
Spin up the switch
to the page 6
Spin up the switch
resume to main page.
E. SELECT THE TRANSCEIVER FEATURES:
1. Spin down the
Switch to select the transceiver feature you need and the OLED screen will display
the features you select.
2. Press the button 1, 2, 3 or 4 once within 3 seconds after finished selection and the OLED screen will
change the display alternatively.
Note: If 5 seconds of inactivity expire, or push the
button, the transceiver features program mode will
exit.
6
Spin down the switch
to the page 2
Spin down the switch
to the page 3
Spin down the switch
to the page 1
Spin down the switch
to the page 4
Spin down the switch
to the page 5
Spin down the switch
to the page 6
Spin down the switch
resume to main page.
E- P1- 1. “BUTTON BEEP” SETTING: Example: Set the “Button Beep Disable”.
It has a short “bi” sound while pressing the button of the remote transceiver
Spin down the switch
to the page 1
Press the button 1 and it
will display previously
setting
Press the button 2 to
change the setting
Press the button and
the setting is done.
E- P1- 2. “BUTTON LOCK” SETTING: Example: Set the “Button Lock Enable”.
Spin down the switch
to the page 1
Press the button 2 and it
will display previously
setting
Press the button 1 to
change the setting
Press the button and
the setting is done.
D- P1- 3. “MELODY / VIBRATION MODE” SETTING: Example: set the Vibration mode.
Spin down the switch
to the page 1
Press the button 3 and it
will display previously
setting
Press the button 2 to
change the setting
Press the button and
the setting is done also
the
icon will display
on the OLED screen
7
Loading...