How it Works
Voxx Electronics
Loading...
APS997Z
Owner's Manual
20 pgs958.13 Kb0

Voxx Electronics APS997Z Owner's Manual

OWNER’S GUIDE
MODEL APS997Z
SECURITY / REMOTE START
WWW.VOXXELECTRONICS.COM
Table of Contents
Using Your Remote Control ................................................................................................3
User Selectable Notication Chirps ...................................................................................4
User Selectable LED ............................................................................................................4
Programmed Transmitter Notication ................................................................................4
Valet Mode ............................................................................................................................5
Manually Overriding the Security System .........................................................................5
Using Your Remote Vehicle Starter ....................................................................................7
Using the “Quick-Stop” Feature ......................................................................................10
Operating the 2 / 4 Hour Start Up Timer Mode ...............................................................11
Turbo Timer Mode (Optional) ..........................................................................................12
Daily Start Timer (Optional) ............................................................................................12
Temperature Start Mode (Optional) ................................................................................12
Status LED, Light Flashes and Siren/Horn Indications ..................................................13
Additional 2-Way LCD Remote Functions .......................................................................14
Remote Control Button Matrix ..........................................................................................16
Replacing Remote Control Batteries ................................................................................17
Programming Your Remote Control .................................................................................18
Warranty Information .........................................................................................................19
2 APS997Z Owners REV.B
Using Your Remote Control
Arming the Security System
To arm the system, exit the vehicle, close all doors, then press the button.
The parking lights will ash one (1) time, indicating the system is armed, has
locked the doors (if equipped and connected) and activated the starter disable feature. The LED status indicator will blink steadily, once per second.
NOTE: The system is equipped with a feature called Silent Choice. If enabled, the system requires a second press of the button to activate an audible arming response from the vehicle.
Disarming the Security System
To disarm the system press the button. The parking lights will ash one
(2) times , indicating the system is disarmed and has unlocked the doors (if equipped and connected).
NOTE: The system is equipped with a feature called Silent Choice. If enabled,
the system requires a second press of the button to activate an audible disarming response from the vehicle. If your system is set up for 2 step unlock, a third press of unlock will activate the audible response.
Two Stage Door Unlock (Optional)
If this feature is enabled on your system, pressing the button one time will
unlock only the driver’s door. Press again within three (3) seconds to unlock the remaining doors.
Activating the Trunk Release Feature (Optional)
If this feature is enabled on your system, pressing and holding the button
for three (3) seconds will open the vehicle’s trunk or hatch.
Activating the AUX Ch. 4-7 Output (Optional)
AUX channel output is an optional feature and programming is required at the
time of installation. Please consult your dealer for more information.
Using the Personal Protection Alarm (Panic)
Press and hold the or button for three (3) seconds to activate the personal
protection alarm. During panic mode, the normal function of the transmitter buttons will be suspended. The transmitter’s and buttons can be used to lock and unlock the door (if the option is installed). To stop the alarm, press and hold the or button on the transmitter again for 3 seconds. The system will automatically stop after thirty (30) seconds.
*Throughout this manual, ‘press’ refers to pressing for less than 1 second; ‘press and hold’ refers to pressing for more than 3 seconds.
32020 Voxx Electronics Corporation. All rights reserved.
Bypassing The Shock Sensor
The included security shock sensor has two stages of detection, Warn-Away and Full Trigger. To arm the system and shock sensor press the button. The
system will chirp and the lights will ash one (1) time.
To Arm the system and bypass the Warn-Away detection stage press the
button two (2) times within ve (5) seconds.
To Arm the Alarm the bypass both detection stages press the button three
(3) times within ve (5) seconds.
City Mode
City Mode allows the user to change the sound of the alarm system to make
it easily identied when the alarm is trigger. To enter City Mode press the button four (4) times within ten (10) seconds.
User Selectable Notication Chirps
System ARM/DISARM chirps can be toggled ON or OFF without entering the programming feature banks.
1. Turn the ignition ON then OFF.
2. Press and release the valet button three (3) times.
The system will respond with one (1) chirp for ON or two (2) chirps for OFF.
User Selectable LED
This feature will control whether the LED is ON or OFF when the system is Armed/Locked and can be toggled ON or OFF without entering the programming feature banks.
1. Turn the ignition ON, OFF, ON, OFF.
2. Press and hold the valet button for ve (5) seconds.
The system LED will respond with one (1) ash for ON or two (2) ashes for
OFF.
Programmed Transmitter Notication
As a security precaution each time the vehicle’s ignition is turn on the status
LED light with ash the number of transmitters programmed into the system.
This helps to identify unauthorized transmitters from accessing your vehicle. If you believe an unauthorized transmitter has been programmed to your system, contact your installing dealer for assistance.
4 APS997Z Owners REV.B
Valet Mode
When valet mode is activated the status LED will light solid, and all security and remote start functions will be disabled. To enter or exit valet mode simply follow the steps outlined below:
1. Turn the vehicle’s ignition ON.
2. Push and hold the valet button.
3. The LED will turn on solid when valet mode is active.
4. Release the valet button.
Manually Overriding the Security System
Your system can be disarmed without the use of the transmitter. This is necessary to operate your vehicle if the transmitter is lost or its battery fails. To by-pass the alarm system;
1. Open the vehicle door. The alarm will sound.
2. Turn the ignition key to the ON position.
3. Within ten (10) seconds, press and release the valet button.
The alarm system will stop sounding and enter the (by-passed) mode. You can now start and operate the vehicle normally.
Stand Alone Valet Override (Optional)
Your system can be disarmed without the use of the transmitter or valet button. This is necessary, since you will need the ability to operate your vehicle if the transmitter is lost or its battery fails. To by-pass the alarm system;
1. Open the vehicle door. The alarm will sound.
2. Cycle the ignition key ON, OFF, ON.
3. Within ten (10) seconds, press and release the Brake pedal three (3) times.
The alarm system will stop sounding and enter the (by-passed) mode. You can now start and operate the vehicle normally. This feature must be programmed ON by an authorized dealer.
52020 Voxx Electronics Corporation. All rights reserved.
Custom Code Valet Override (Optional)
Unlike the default Valet Override, Custom Code Override is a user
personalized code that o󰀨ers a higher lever of security. If the user chooses to
use Custom Code Override, Feature Bank 2 ; Feature 9 must be programmed for “Custom Code”. Once the option has been selected the code must be programmed. Once the Custom Code is programmed it cannot be changed
without rst disarming the alarm.
Custom Code Override Procedure
The Custom Code is made up of 2 numbers. Each chosen number must be between digits 1-9. The default Custom Code is “11”. To disarm the alarm using the Custom Code option:
1. Turn the vehicle ignition to ON.
2. Within ve (5) seconds, Press the valet button one (1) time.
3. Within ve (5) seconds, Turn the ignition OFF/ON.
4. Within ve (5) seconds, Press the valet button one (1) time.
5. Turn the vehicle ignition to OFF then ON to start the vehicle.
Custom Code Programming Procedure
In this example, the user has selected Custom Code “23”. To program a user selected custom code:
Start with the alarm disarmed.
1. Turn the ignition to the ON position.
2. Within ten (10) seconds, press the valet button three (3) times to enter programming.
3. Within ten (10) seconds, Cycle the ignition OFF/ON, OFF/ON, OFF/ ON. The system will beep one (1) time.
4. Within ten (10) seconds, Press the valet button two (2) times. This
number will indicate the rst digit of the chosen Custom Code.
5. Within ten (10) seconds, Cycle the ignition OFF/ON.
6. Within ten (10) seconds, Press the valet button three (3) times. This number will indicate the second digit of the chosen Custom Code.
7. Cycle the ignition OFF.
If the Custom Code was accepted the LED will ash the rst number (2),
pause, then the second number (3). This will repeat two (2) more times to
conrm the Custom Code entry. If after fteen (15) seconds the LED does not ash please repeat steps 1-7.
6 APS997Z Owners REV.B
Loading...
+ 14 hidden pages
Buy Points How it Works FAQ Contact Us Questions and Suggestions Privacy Policy Cookie Policy Terms of Use