Voxx Accessories PNMWIFIAC User Manual

WIFI BABY MONITOR

What’s inside

Welcome!................................................................. 2

Getting started ...................................................... 3

Tour of the system ............................................... 9

Everyday use .........................................................13

Motion detection ........................................... 14

Sound detection ............................................ 14

Auto-record time .......................................... 15

Battery life........................................................15

Temperature alarm ....................................... 16

Music ...................................................................16

Share camera with friend .......................... 17

Flip horizontally / vertically .....................18

User Guide

PNMWIFIAC

Camera time set ............................................18

Camera info ..................................................... 19

Delete Camera ...............................................19

Troubleshooting / FAQs ................................. 20

WELCOME!

This WiFi Baby Monitor makes it
simple to keep your eyes and ears
on your little one from anywhere!
This guide takes you through the
steps to get started!

Check out our setup videos

On your computer, go to
http://bit.ly/pnwifi-setup or scan the
QR code here.

Before you start...

Make sure you read the Important Information
sheet included in this package.

2

Step 1: Unpack

The accessories:

(1) Power adapter

(1) 10’ charging cable

(2) Mounting screws

WiFi camera

GETTING STARTED

Step 2: Position the camera

Find a location for the camera
that gives you the best view of
your baby in his or her crib.

Place the camera on a flat surface, like a dresser
or shelf, or mount the camera to a wall using the
keyhole slots on its bottom (see the mounting
template included in this package).

IMPORTANT: NEVER place the camera or cords of
any kind inside the crib. NEVER place the camera
or cords within reach of the baby.

Getting Started

WARNING

Strangulation Hazard:

Children have STRANGLED
in cords. Keep this cord out
of the reach
of children
(more than
3ft (0.9m)
away).
Never use
extension
cords with AC Adapters.
Only use the AC Adapters
provided.

3

Getting Started

Step 3: Test your WiFi signal

Your Project Nursery WiFi Camera needs strong
enough signal from your WiFi router in order to
send its video signal.

Here’s how to test the strength of your WiFi signal
in your baby’s nursery using your smartphone or
other portable wireless device (like a tablet or iPod
touch).

First, go to where you want to put the camera.

Make sure your smartphone
or other portable wireless
device is connected to the
WiFi network you want to
test. Look at the WiFi icon on
your device screen to see the
strength of the connection.
For example, on iOS devices
look in the upper left-hand
corner of the screen for the
WiFi icon (shown here).

For best results, look for a location with at least
50% strength to use the WiFi camera.

4

Step 4: Plug in the camera

Plug one end of the
included charging cable
into the DC In jack on the
back of the camera.

Plug the other end into
the included power
adapter. Then plug the
adapter into an outlet or
surge protector.

The camera turns on
automatically when you
plug it in (the indicator
light on its back panel
turns solid red).

Sign Up

Step 5: Download and install the
Project Nursery Monitor App on
your phone or tablet

In the Google Play or Apple App
Stores, search for “PROJECT
NURSERY MONITOR” and look
for the icon shown here. Then
download and install the App.

Step 6: Launch the Project
Nursery Monitor App

Once the Project Nursery Monitor App has
installed on your smarphone or tablet, press the
icon to launch the App.

Step 7: Create a Project Nursery
user name and password

The first time you launch the
Project Nursery App, you’ll
need to create a user name

®

Register

Login

Username

Email Address

Password

Confirm Password

Sign Up

and password so that you can
access your camera securely.

Press the Register button to
start, then follow the steps to
set up your account.

IMPORTANT: Make sure you
give a valid email address that
you have easy access to. The
App will use this address if
you ever need to recover or
reset your password.

Once you’ve finished
creating your user name and
password, the App will ask
you to Login with the name
and password you created.

IMPORTANT: Your user
name cannot contain special
characters (like “@”)—only
letters and numbers.

Getting Started

5

Getting Started

®

Sally’s Nursery

QR code scanner

Step 8: Pair the WiFi camera with
the App.

Make sure the Project Nursery App is open on your
phone or tablet. Also make sure that your phone
or table is connected to your WiFi network.

Device List Message My Center

Add Camera

Add new camera with WiFi

Add new camera with QR code

Get shared camera from friend

6

®

In the App’s home screen,
press the

Camera) in the upper right
corner of the screen.

In the next screen, press the
Add new camera with WiFi
button.

The App will prompt you to
make sure your camera is on.
If you haven’t already turned it
on, press the POWER button
on the right side of the camera
(the camera’s LED lights up),
then press the Next step button
in the App.

icon (Add

ID:

Camera name:

Add Camera

Next step

Scan QR code located

on bottom of camera

Press to open

The next screen in the App lets
you name the camera you’re
setting up and prompts you
to scan the QR code on the
bottom of the camera.

To name the camera you’re
setting up: Press in the
Camera name field and enter

the name you want to use.

To scan the QR code on the
WiFi camera: Find the QR

code on the bottom of the
WiFi camera. Position your
smartphone or tablet so
that its camera can scan this
QR code. Then press where
indicated in the App to scan
this QR code.

Configure WiFi

your camera is successfully connected and ready for you to use.

Configure WiFi

1. Your camera should be plugged in and turned ON.
Press the “Set” button on the bottom of your camera for 1
second.You will hear one beep and the LED will start
blinking red.

2. Choose WiFi SSID (or network name) and enter
password below. Make sure you enter the info correctly.
If your WiFi SSID does not have a password, you will need to
create one. This is for your safety and security. Consult the
user guide for your WiFi router/AP to add a password.

Helpful Hint: Click on the lock icon in the password area
to hide or display text.

3. After you’ve entered your WiFi info below, press “Next
step.” Your camera will begin connecting to your WiFi
network. This can take 2–3 minutes to complete.

When you hear two beeps and the LED turns solid green,
your camera is successfully connected and ready for you to use.

Configure WiFi

1. Your camera should be plugged in and turned ON.
Press the “Set” button on the bottom of your camera for 1
second.You will hear one beep and the LED will start
blinking red.

2. Choose WiFi SSID (or network name) and enter
password below. Make sure you enter the info correctly.
If your WiFi SSID does not have a password, you will need to
create one. This is for your safety and security. Consult the
user guide for your WiFi router/AP to add a password.

Helpful Hint: Click on the lock icon in the password area
to hide or display text.

3. After you’ve entered your WiFi info below, press “Next
step.” Your camera will begin connecting to your WiFi
network. This can take 2–3 minutes to complete.

When you hear two beeps and the LED turns solid green,

Next step

After you’ve scanned the QR
code on the bottom of the
WiFi Camera, the App will ask
you to press the SET button on
the bottom of the camera and
enter the name (WIFI SSID)
and password of your WiFi
network.

Find the SET button on the
bottom of the WiFi camera.
Press it for one second (until
the camera gives an audio
signal).

Enter the name (WIFI SSID)
and password for your home
WiFi network in the App.

Next step

IMPORTANT: Double check that you’ve typed your
network name and password correctly—otherwise,
the camera won’t work with the App!

Once you’ve finished entering your network name
and password, press the Next step button on the
App screen. The indicator light on the back of the
WiFi camera starts flashing—the camera is trying
to join your WiFi network.

Once the WiFi camera has
successfully connected to your
WiFi network, you’ll see the
Success screen in the App and
the indicator light on the back
of the camera will turn green.

Congratulations—you’ve just
set up your first camera!

Congratulations!

Camera successfully added!

IMPORTANT: If the WiFi
camera does not connect,
follow the instructions in the
App to troubleshoot.

Getting Started

7

Getting Started

®

Step 9: Choose the camera from
the home screen

®

Device ID：123456 7891234560

Sally’s nursery

Device List Message My Center

Sally’s nursery

0

2016-1-28-12:00

HD SD

RECORD SNAPSHOT

JOYSTICK

TALK SOUNDON

8

Sally’s nursery

Device ID：1 234567 891234560

Press the part of the home
screen showing the camera
you set up in order to choose
this camera.

The Camera View screen is
your gateway to total control
of your WiFi camera from
virtually anywhere.

The next chapter gives you a
tour of the features available
from this screen.