Voxx Accessories HSDB1 User Manual
NOW YOU NEVER HAVE TO ASK…
WHO’S THERE?
HSDB1 QSG 00
1
~ 1.5 in
EASY SETUP
1
2
Mount the doorbell camera
to an existing doorbell
Download the RCA
Security App
WHAT YOU GET
WiFi doorbell
camera
with 1 faceplate
installed
3 extra faceplate options
Mounting
template
7/32” Masonry
Drill Bit
1/16” Wood
Drill Bit
3
4
Connect to Wi-Fi
Customize your device
settings
Installation kit:
#1 Phillips-Head
Screwdriver
x2 Mounting screws
x2 Mounting anchors
x2 Set screws
Security
screwdriver
x2 Wire nuts
x2 Wire leads
Mounting Template
Paste the template on the
.
required place.Drill screw
holes and cable holes
according to the template.
Hole A:Cable Hole.
.
Hole 1:Wall Mounting Screw
Hole.
Drill
TOOLS YOU’LL NEED
2
MOUNT THE DOORBELL CAMERA
~ 1.5 in
1
2
3
Turn o power to your doorbell’s circuit
Find the breaker that controls the
circuit for your doorbell. Turn it o
before you continue installation.
Remove your existing doorbell
Carefully remove your existing
doorbell from the wall. Then unhook
Remove &
unhook
your home’s wiring from the doorbell’s
terminals.
Apply the mounting template sticker to the wall
~ 1.5 in
Mounting Template
Paste the template on the
.
~ 4.5 in
required place.Drill screw
holes and cable holes
according to the template.
Hole A:Cable Hole.
.
Hole 1:Wall Mounting Screw
Hole.
Apply
Align the space marked “Hole A”
on the mounting template with the
access point for the cables that will
power the doorbell camera.
Stick the mounting template sticker to
the wall.
Drill holes for the doorbell camera
4
Insert one of the drill bits
—OR—
Insert
in your drill—for masonry
or brick, use the larger drill
bit provided. For wood,
the smaller.
Drill two holes where
Drill
indicated by the mounting
template.
Remove the faceplate from the doorbell camera
5
Before you mount it, take the faceplate o the
doorbell camera—you’ll need access to several
items behind the faceplate during setup.
To remove the faceplate: Push down on the top
and bottom of the doorbell camera and push the
button and just below the camera to remove the
doorbell camera from the faceplate. Be careful not
to touch the camera lens!
continues on the next page...
3
MOUNT THE DOORBELL CAMERA (continued)
Connect the doorbell camera to home power
6
Check if your home’s doorbell power wires are long enough to
connect directly to the terminals on the back of the doorbell
camera.
Terminals
Loosen
Doorbell
camera
back
If your home’s doorbell power wires are long
enough:
Use the screwdriver provided in this package
to loosen the terminal screws on the back of
the doorbell camera.
Wire nut
Home
doorbell
wires
Twist
Wire
leads
Terminals
If your home’s doorbell power wires are NOT
long enough:
Use the wire leads and wire nuts included in
this package to connect them to the doorbell
camera.
First, put the ends of one wire lead and one
home doorbell wire together and insert them
into a wire nut. Then twist the wire nut until
you feel tension. Repeat with the other wire
lead, home doorbell wire, and wire nut.
Home
doorbell
wires
4
Terminals
Tighten
Connect the doorbell power wires directly
to the terminals on the back of the doorbell
camera. Loop each wire end around each
terminal on the back of the doorbell camera.
Note: It doesn’t matter which wire you put on
which terminal.
Tighten the screws to hold the wires rmly in
place.
IMPORTANT! Handle the doorbell camera carefully! Make
sure not to scratch its lens.
Doorbell
camera
back
Next, unscrew the terminal screws on the back
of the doorbell camara and remove them.
Unscrew
& remove
Place each screw through the ring on the other
end of each wire lead, then screw the terminal
screws back onto the doorbell camera.
Tighten
Loading...