Voxson VLCD 26D, VLCD 32D, VLCD 37D, VLCD 42D Instructions Manual

English

Before using this product, please read the security instructions first

and bear them in mind when using the product.

OWNERS
INSTRUCTIONS

TFT LCD TV -

Built in DVD/MPEG-4(Option) Player

37”42

”

32

”

26 /

/

”

Eng - 2

Warning

TO PREVENT FIRE OR SHOCK HAZARD. DO NOT EXPOSE
THIS APPLIANCE TO RAIN OR MOISTURE.

THIS SYMBOL IS INTENDED TO ALERT THE
USER TO THE PRESENCE OF UNINSULATED.
DANGEROUS VOLTAGE. WITHIN THE
PRODUCTS ENCLOSURE THAT MAY BE OF
SUFFICIENT MAGNITUDE TO CONSTITUTE A
RISK OF ELECTRIC SHOCK TO PERSONS.

THIS SYMBOL IS INTENDED TO ALERT THE
USER TO THE PRESENCE OF IMPORTANT
OPERATING AND MAINTENANCE
(SERVICING) INSTRUCTIONS IN THE
LITERATURE ACCOMPANYING THE
APPLIANCE.

This equipment has been designed and manufactured
to meet international safety standards but, like any
electrical equipment, care must be taken if you are to
obtain the best results and safety is to be assured. So,
please read the points below for your own safety. They
are of a general nature, intended to help you with all
your electronic consumer products and some points may
not apply to the goods you have just purchased.

• Read these instructions.

• Keep these instructions.

• Heed all warnings.

• Follow all instructions.

• Do not use this apparatus near water.

• Clean only with a dry cloth.

• Do not block any ventilation openings.
Install in accordance with the manufacturer’s
instructions.

• Do not install near any heat sources such as
radiators, heat registers, stoves, or other apparatus
(including amplifiers) that produce heat.

• This TV is not completely disconnected from a power
supply line, as minute current is consumed even when
the POWER switch is turned off (Depend on the model).

• Do not place hot objects or naked flame sources, such
as lighted candles or highlights on, or close to the TV.
High temperatures can melt plastic and lead to fires.

• Do not set on top of the TV any object or container
that might spill liquids or small objects into the TV.

•Protect the power cord from being walked on or
pinched, particularly at plugs, convenience receptacles,
and the point where it exits the apparatus.

• Only use attachments/accessories specified by the
manufacturer.

• Use only with the cart, stand, tripod, bracket, or
table specified by the manufacturer, or sold with the
apparatus. When a cart is used, use caution when
moving the cart/apparatus combination to avoid
injury from tip-over.

• Unplug this apparatus during lightning storms or
when unused for long periods of time.

• Refer all servicing to qualified service personnel.
Servicing is required when the apparatus has been
damaged in any way, such as power supply cord or
plug is damaged, liquid has been spilled or objects
have fallen into the apparatus, the apparatus has
been exposed to rain or moisture, does not operate
normally, or has been dropped.

• The apparatus shall not be exposed to dripping or
splashing and no objects filled with liquids, such as

vases, shall be placed on the apparatus.

• Please keep the minimum distance 100mm from the
back side of this product to the back wall.

• Where the MAINS plug or an appliance coupler is used
as the disconnect device, the disconnect device shall
remain readily operable.

• Do not defeat the safety purpose of the polarized or
grounding-type plug. A grounding type plug has two
blades with one wider than the other. A grounding
type plug has two blades and a third grounding prong.
The side blade or the third prong are provided for your safety.
If the provided plug does not fit into your outlet, consult
an electrician for replacement of the obsolete outlet.

• This product complies with DHHS RULES 21 CFR
Chapter 1, Subchapter J applicable at the date of
Manufacture.

CAUTION : Danger of explosion if battery is incorrectly replaced.

Replace only with the same or equivalent type.

CAUTION : These servicing instruction are for use by qualified service
personnel only. To reduce the electric shock do not perform any servicing
other than that contained in the operating instructions unless you are
qualified to do so.

WARNING : This apparatus should be connected to a MAINS socket
outlet with a protective earthing connection.

Important Safety Instructions

Safety Instruction

CAUTION

CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT
REMOVE COVER (OR BACK). NO USER-SERVICEABLE PARTS
INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.

RISK OF ELECTRIC SHOCK DO NOT OPEN

NO USER-SERVICEABLE PARTS INSIDE

Disposal of Old Electrical & Electronic Equipment (Applicable in the European
Union and other European countries with separate collection systems)

This symbol on the product or on its packaging indicates that this product shall not be treated as
household waste. Instead it shall be handed over to the applicable collection point for the recycling of
electrical and electronic equipment. By ensuring this product is disposed of correctly, you will help prevent
potential negative consequences for the environment and human health, which could otherwise be
caused by inappropriate waste handling of this product. The recycling of materials will help to conserve
natural resources. For more detailed information about recycling of this product, please contact your local
city office, your household waste disposal service or the shop where you purchased the product.

3 - Eng

English

• Safety Instruction.....................................................2

• Overview...................................................................4

• Remote Control .......................................................6

• Connecting Your TV ................................................7

• Check Before Using .................................................9

• TV Function

Watching TV.........................................................9

Storing Channels Automatically .......................10

Manual Storing of Channels .............................10

Channel Name....................................................10

Activating the Child Lock .................................11

Program Edit ......................................................11

Changing Channel .............................................12

When the Picture Quality is Poor or Unstable

....12

Selecting the Picture Status ..............................12

Adjusting the Picture Settings ..........................13

Selecting the Sound Mode................................13

Adjusting the Balance .......................................13

Adjusting the Headphone Volume ..................14

Adjusting the Equaliser .....................................14

Choosing a Soundtrack .....................................14

Changing the Screen Size..................................15

Freezing the Picture...........................................15

Viewing Picture-in-Picture.................................16

Changing the Source of the PIP Window........16

Changing the PIP Window Channel.................16

Changing the Position of the PIP Window .....17

Selecting the Speaker Output in the PIP Screen Mode....

17

Selecting the Headphone Output in the PIP Screen Mode...

17

Setting the Clock................................................18

Setting the On/Off Timer ..................................18

Selecting the ON Timer Channel/

Adjusting the ON Timer Volume ......................18

Setting the Sleep Timer.....................................19

Melody Function ................................................19

Change Password...............................................19

• TTX Function

Teletext ...............................................................20

Displaying the Teletext Information ................20

Selecting a Page by Number.............................21

Using FLOF to Select a Page .............................21

• PC Function

Connecting to a PC ............................................22

Adjusting the PC ................................................23

• DVD Function (Depend on the model)

Playing DVD’s .....................................................24

Displaying the Playback Status .........................24

Searching for a Specific Screen/Song ...............24

Repeating a Title, Chapter(DVD), Track(CD)....25

Changing the Audio Language/

Changing the Subtitle Language .....................25

Changing the Size and Angle of the Screen ...25

Additional Function...........................................26

Setting a Specific DVD Title or Chapter...........26

Playing MP3 Discs ..............................................27

Playing MPEG-4 Discs (Option) .........................27

Playing Kodak Picture CD and JPEG File..........28

Using the Setup Menu.......................................29

• MPEG-4 Function (Depend on the model)

MPEG-4 feature Table........................................31

DivX® VOD Playback.........................................32

• Using ARM on the Outer Wall .............................32

• Troubleshooting.....................................................33

• Specifications .........................................................35

• Appendix ................................................................36

Contents

Front View

ΠMASTER SWITCH (Depend on the model)
´ Remote Control Sensor
ˇ POWER: Turns the TV on and off.
¨ LED Lights
ˆ VOLUME: Increases or decreases the volume.

This is also used to select the “MOVE&ADJUST”
item on the on-screen menu.

Ø PROGRAM: Changes channels or

“MOVE&ADJUST” to items on the on-screen
menu.

∏ MENU: To access or close menus, simultaneously.
” TV/VIDEO: Selects an external device connected

to the TV.

<DVD> - Depend on the model

’ PLAY/PAUSE: Play the DVD or temporarily stop

playback.

˝ STOP: Stop the DVD playback.
Ô OPEN/CLOSE: OPEN/CLOSE the DVD.

Overview

Eng - 4

• VLCD 42D

• VLCD 26D, VLCD 32D, VLCD 37D

Option

Option

English

5 - Eng

Rear Panel Jacks

ΠPC INPUT (VIDEO/AUDIO) JACKS
´ RS-232C INPUT JACK
ˇ HDMI INPUT( 1, 2), DVI INPUT(VIDEO/AUDIO:L/R) JACK
¨ COMPONENT JACKS (VIDEO : Y, Pb, Pr/AUDIO : L/R)

: COMPONENT IN 1, 2

ˆ S-VIDEO INPUT JACK
Ø DIGITAL AUDIO OUTPUT JACK
∏ VIDEO1,2 (VIDEO/AUDIO) INPUT JACKS
” LINE (VIDEO/AUDIO) OUTPUT JACKS
’ HEADPHONE JACK

: Used for headphones that can be purchased

additionally.

˝ LOOP-OUT CABLE (from ANALOG TV ANTENNA INPUT)
Ô ANALOG TV ANTENNA INPUT JACK
 DIGITAL TV ANTENNA INPUT JACK

For more details on connections see page 7~9.

Eng - 6

Remote Control

ΠPOWER: Turns the TV on and off.
´ DISPLAY: Displays the current channel and the audio-

video settings.

ˇ TV: Switches to TV mode.
¨ DVB-T/MENU: Switches to DVB-T mode /

Opens the main menu.

ˆ PC: Switches to PC mode.
Ø LINE: External input selection.
∏ LIST: Channel List.
” OPT: Configuration Menu.
’ EPG: Electronic program guide.
˝ i: Information.

Ô

NUMBER BUTTONS: Selects channels directly on the TV.

 -/--: Selects channels over 10. For example, to select

channel 21, press “-/--” then press “2”, “1”.

Ò PRE: Moves to the previous channel.
Ú VOL: Increases or decreases the volume.
Æ PROG: Changes channels.
ı M/S: Sound mode selection.
˜ STILL(OPTION): Freezes a moving picture on the screen.
¯ SLEEP: Selects a preset time interval for automatic

shutoff.

˘ P.SIZE: Changes the screen size.
¿ TV.MENU: Displays the OSD menu.
¸ EXIT/CANCEL: Exit the current configuration /

To exit from the teletext display.

˛ MUTE: Temporarily mute the sound.
◊ TTX: Switches to Teletext mode.
± ARROW/ENTER:

Select an item of menu / Change confirmation/ VOL.
+,- / PROG up,down control.

≠ ON/OFF(OPTION): Turns PIP on or off.
– SOUND(OPTION): Changes the audio signal source

between the main screen and the PIP window.

<DVD & TTX> - Depend on the model

— OPEN/CLOSE: OPEN/CLOSE the DVD tray.
÷ SETUP: For initial DVD player settings.
® STOP: Stop the DVD playback.
∑ PLAY/PAUSE:

Play the DVD or temporarily stop playback.

µ SLOW: For fast and slow playback.
¥ STEP: For playing one frame at a time.
≥ REC: DVD R/W (option)

≤ INPUT: DVD R/W (option)
π HOLD/REPEAT: Teletext page / For specifying and

repeating playback of a segment.

æ INDEX/A-B: Programme selection by name /

For repeated playback of disc titles, chapters or sound.

ø MIX/AUDIO: Video & TTX MIX/

For selecting the audio language.
SUB PAGE/SUBTITLE: Teletext SUB-PAGE /
For selecting the SUBTITLE language.
REVEAL/GOTO: Teletext reveal/ For jumping to a

specified location.

TITLE: For selecting a title on the disc.
MENU: For displaying the menu contained in the disc.
ANGLE: For viewing scenes from different.
ZOOM: For magnifying the screen.

BOOK MARK: To SAVE a specific frame for later

viewing.

PRE PAGE: Teletext previous page.

NEXT PAGE: Teletext NEXTPAGE.

45

46

7 - Eng

English

Connecting Your TV

Connecting an Antenna or Cable without a Decoder box

Connecting a Digital Audio System

Connection Procedures

ΠConnect the DIGITAL OUT jack on the back

of your TV to the DIGITAL IN jack of the Decoder
or AV amplifier.

´ Tu rn the digital amp on and select the external

input mode.

Audio System

Coaxial
Cable

VHF, UHF or Cable

VHF, UHF or Cable

• Analog and Digital TV signals provided on one antenna • Analog and Digital TV signals provided on two
separate antennas

75-ohm coaxial cable

75-ohm coaxial cable

Digital Antenna

Analog Antenna

Connection Procedures

ΠConnect the AUDIO CABLES between the AUDIO

OUT L and R jacks on the back of your TV and the
corresponding AUDIO INPUT jacks on external TV.

´ Connect the VIDEO CABLE between the VIDEO OUT

jack on the back of your TV and the corresponding
VIDEO INPUT jack on external TV.

To watch the external TV

Œ Tu rn the external TV on and select ‘VIDEO’ using the

external input button.

´ Tu rn the your TV on.

Connecting a External TV

External TV

Video
Cable

Audio
Cable

Eng - 8

Connection Procedures

ΠConnect the antenna cable to the ANTENNA IN

terminal on the back of your VCR.

´ Connect the VIDEO/AUDIO INPUT jacks of the TV

and the video/audio output jacks of your VCR with
the video/audio cables. (Connect the cable to the
terminal of the same colour)

-You can use the S-Video cable to connect a VCR or
a DVD player for better video quality.

- If your VCR does not support stereo sound,
connect the mono audio out jack to the AUDIO
INPUT (left) jack.

Procedures for watching a video over a VCR

Turn the TV on, and select ‘VIDEO’ using the LINE
button on the remote control.

- If you have connected a S-Video cable, select
‘S-VIDEO’.

Connecting the Video or S-Video/Audio Jacks

VCR/DVD Player/STB

Video Cable

Audio Cable

OR

S-Video Cable

Connection Procedures

ΠConnect the AUDIO CABLES between the AUDIO

OUT L and R jacks on the back of your TV and the
corresponding AUDIO INPUT jacks on external TV.

´ Connect the VIDEO CABLE between the VIDEO OUT

jack on the back of your TV and the corresponding
VIDEO INPUT jack on external TV.

To watch the external TV

Œ Tu rn the external TV on and select ‘VIDEO’ using the

external input button.

´ Tu rn the your TV on.

Connecting a External TV

External TV

Video
Cable

Audio
Cable

Connection Procedures

ΠThe COMPONENT VIDEO IN and COMPONENT

AUDIO IN

connectors are used for equipment
with a DVD or DTV receiver out. (480i/60Hz,
480p/60Hz, 576i/50Hz, 576p/50Hz, 720p/50Hz,
720p/60Hz, 1080i/50Hz,1080i/60Hz)

To watch the DTV

Œ Tu rn the TV on, and select ‘COMPONENT’ using

the

LINE button on the remote control.

´ Tu rn the DTV Receiver on.

Connecting the DTV Receiver

DTV Receiver

DTV Receiver

Audio
Cable

Component

Cable

HDMI

Connection Procedures

ΠConnect the HDMI input jack of the TV and the

HDMI output jack of your DTV Receiver (480p/60Hz,
576p/50Hz, 720p/50Hz, 720p/60Hz, 1080i/50Hz,
1080i/60Hz).

HDMI Cable

Connecting the HDMI JACK

•Warning : Do not Connect DVI audio cable.

English

9 - Eng

ΠPress the TV.MENU button. The OSD MENU will

be displayed.

´ Select FUNCTION using the œ/√ button.
ˇ LANGUAGE using the ▲/▼ button and then press

the

√ button.

¨ Select the desired menu language using the ▲/▼

button.

ˆ Press the EXIT button to exit the menu.

Selecting the Menu Language

Turning the TV On and OFF

Note.

when you power on this product in the first time, the product will ask you language and counrty selection on
the screen menu. Thus, you should select your own language and contry by

▲/▼ and ENTER button.

ΠPlug the mains lead into an appropriate socket.
´ Press the POWER switch on the bottom of the television toward “ON”(I) (Depend on the model).
ˇ Press the POWER button on the remote control (or on the front panel of the unit.)

You can also switch on by pressing the

PROG ▲/▼ buttons.

• When you turn the power ON, the screen appears and the POWER/STANDBY light is turned off.

• When you turn the power OFF, the screen goes blank, and the POWER/STANDBY light turns red.

• Do not leave your television in Standby mode for long periods of time (when you are away on holiday, for
example). Turn your television off by pressing the

POWER switch toward “OFF”(O)(Depend on the model).

It is best to unplug the set from the mains and aerial.

Watching TV

Press the DISPLAY button on the remote control. The TV will display the input source, the picture mode, the
sound mode, the STEREO mode, the sleep time, the current time, and the pip mode.

Viewing the Status Information

MENU

PICTURE

SIZE
PIP
TIME
MELODY
LANGUAGE
CHANGE PASSWORD

œ

WIDE

√
√
√

œ

OFF

√

œ

ENGLISH

√
√

TV Function

Please check the following check list before using the TV.

ΠIs the antenna cable connected properly?
´ Are the remote control batteries installed properly?

- Install two AAA size batteries according to the
correct polarity.

- The remote control works up to about 7~10m

from the TV, 3m to the left or right of the TV, and
to within 30 degrees from the remote control
sensor of the TV.

ˇ Have the receive channels been configured?
¨ Are the cables connected to any external devices

connected properly?

Check Before Using

Connecting the HDMI JACK (USE DVI JACK)

Connection Procedures

ΠConnect the HDMI input jack of the TV and the DVI

output jack of your DTV Receiver (Using the adapter
or HDMI cable).

´ Connect the DVI audio input jacks of the TV and the

DVI audio output jacks of your DTV Receiver with
the audio cable (480p/60Hz, 576p/50Hz, 720p/50Hz,
720p/60Hz, 1080i/50Hz,1080i/60Hz).

ˇ

VESA Standard Mode (Resolution/Vertical Fraequency)

800x600/60Hz, 800x600/72Hz, 800x600/75Hz,
1024x768/60Hz, 1024x768/70.1Hz,1280x768/60Hz.

Audio Cable

DVI Cable

DVI to HDMI

adapter

DTV Receiver

PCFUNCTIONSETUPSOUND

Move PreviousAdjust Exit

ΠPress the TV.MENU button. The OSD MENU will

be displayed.

´ Select SETUP using the œ/√ button.
ˇ Select AUTO PROGRAMMING using the ▲/▼

button and then press the √ button.

¨ Select your COUNTRY using the œ/√ button and

then press the

▼ button.

Eng - 10

When storing channels manually, you can choose:

-Whether or not to store each of the channels
found.

- The programme number by which you wish to
identify each stored channel.

ΠPress the TV.MENU button. The OSD MENU will

be displayed.

´ Select SETUP using the œ/√ button.
ˇ Select MANUAL PROGRAM using the ▲/▼ button

and then press the

√ button.

¨ Select SYSTEM using the œ/√ button.

AUTO

➞ BG ➞ I ➞ DK➞ M ➞ L ➞ LP ➞ AUTO

ˆ Select PROGRAM NO. using the ▲/▼ button and

press the

œ/√ button to select the required

channel number.

Ø Select SEARCH using the ▲/▼ button and then

press the

√ button.

The tune scans the frequency range until the first
channel on the channel that you selected is
received on your screen.

∏ Select STORE using the ▲/▼ button and then

press the

√ button.

” Repeat Step 5 to 7 for each channel to be stored.

Manual Storing of Channels

ΠPress the TV.MENU button. The OSD MENU will

be displayed.

´ Select SETUP using the œ/√ button.
ˇ Select Program Edit using the ▲/▼ button and

then press the

√ button.

¨ Select NAME using the œ/√ button and press the

▲/▼/œ/√ buttons to edit the name.
▲/▼: Select the characters (A~ Z, 0~9, -, +).

œ/√: move on the previous or next letter.

ˆ Press the EXIT button to exit the menu.

Channel Name

Storing Channels Automatically

Adjust the volume using the VOL ▲/▼ button.

Adjusting the Volume

Press the MUTE button. You can conveniently use the MUTE button when a telephone or a door bell rings.
To cancel, press the

MUTE button again.

Muting the Sound

Press the LINE button. For connection and setup procedures, refer to page 7-9.

Viewing a Video, DVD or COMPONENT

MENU

PICTURE

Auto Program
Manual Program
Program Edit

√
√
√

PCFUNCTIONSETUPSOUND

Move PreviousAdjust Exit

MENU

PICTURE

Auto Program
Manual Program
Program Edit

√
√
√

PCFUNCTIONSETUPSOUND

Move PreviousAdjust Exit

MENU

PICTURE

Auto Program
Manual Program
Program Edit

√
√
√

PCFUNCTIONSETUPSOUND

Move PreviousAdjust Exit

English

11 - Eng

This function enables you to delete, copy, move or
skip the stored programs.

ΠSelect the channel to tune using the numeric or

channel buttons.

´ Press the TV.MENU button. The OSD MENU will

be displayed.

ˇ Select SETUP using the œ/√ button.
¨ Select PROGRAM EDIT using the ▲/▼ button and

then press the

√ button.

This feature allows you to prevent unauthorised users,
such as children, from watching unsuitable programmes
by muting out video and audio. Child Lock cannot be
released using front panel buttons. Only remote
control can release the Child Lock setting, so keep the
remote control away from children.

ΠPress the TV.MENU button. The OSD MENU will be

displayed.

´ Select SETUP using the œ/√ button.
ˇ Select MANUAL PROGRAM using the ▲/▼ button

and then press the

√ button.

¨ Select CHILD LOCK using the ▲/▼ button.

ˆ To lock the channel, select LOCK by pressing

the

œ/√ button.

Œ Select a program to the deleted with the ▲/▼ buttons.
´ Press the RED button. The selected program is

deleted.
All the following programs are shifted up one

position.

Delete a Program

Œ

Select a program to the copied with the ▲/▼ buttons.

´ Press the YELLOW button.

Move the program to the desired program number
with the

▲/▼ buttons.

All the following programs are shifted down one
position.

ˇ Press the YELLOW button again to release this

function.

Copy a Program

Œ Select a program to the moved with the ▲/▼ buttons.
´ Press the GREEN button.
ˇ Move the program to the desired program number

with the

▲/▼ buttons.

¨ Press the GREEN button again to release this

function.

Moving a Program

Œ Select a program to the skipped with the ▲/▼

buttons.

´ Press the BLUE button. The skipped program turns

to ‘YES’.

ˇ Press the BLUE button again to release this function.

When a program number is skipped it means
that you will be unable to select it using the

▲/▼
button during normal TV viewing. If you want to
select the skipped program, directly enter program
number with the number buttons or select it in the
program edit or table menu.

Skipping a Program Number

Program Edit

Activating the Child Lock

Œ~¨ STEP1~STEP4 is the same as that of Activating

the Child Lock.

ˆ When a login dialog box appears, enter the

password to deactivate the CHILD LOCK.

Note

• When child lock is activated, only entering the correct password
will proceed to the operation before you can do auto or manual
searches. Everything previously locked will be unlocked.

Activating the Child Unlock

MENU

PICTURE

Pr

00
01
02
03
04
05
06
07

Name

- - - - -

- - - - -

- - - - -

- - - - -

- - - - -

- - - - -

- - - - -

- - - - -

Program Edit

Ch

- - -

- - -

- - -

- - -

- - -

- - -

- - -

- - -

Sound

B/G

LP
B/G
B/G
B/G
B/G
B/G
B/G

DELETE

MOVE

COPY

SKIP

Skip

YES
YES
YES
YES
YES
YES
YES
YES

PCFUNCTIONSETUPSOUND

Move PreviousAdjust Exit

MENU

PICTURE

System
Fine Tune
Program NO.
Child Lock
Store
Search

œ
œ
œ
œ
œ

LP

0
1

OK

--

œ

√

√
√
√
√
√

PCFUNCTIONSETUPSOUND

Move PreviousAdjust Exit

You can select a video mode from among USER,
STANDARD, DYNAMIC, or MILD mode according to
your personal preference.

ΠPress the TV.MENU button. The OSD MENU will

be displayed.

´ Select PICTURE using the œ/√ button.
ˇ Select the desired PICTURE STATUS using the œ/√

button. Whenever you press this button, PICTURE
STATUS changes to STANDARD

➞ DYNAMIC ➞

MILD ➞ USER mode, in this order.

¨ Press the EXIT button to exit the menu.

Picture Status

•STANDARD: Select this mode when the surrounding
illumination is bright.

• DYNAMIC: Select this mode to increase picture clarity

and sharpness.

• MILD: Select this mode when viewing the TV when the

light is low.

• USER: Select this mode if you want to adjust the settings

according to your personal preferences.

Eng - 12

Use fine tuning to adjust a particular channel for
better picture quality when noise interferes, colour
quality is poor, or the screen is unstable.

ΠSelect the channel to tune using the numeric or

channel buttons.

´ Press the TV.MENU button. The OSD MENU will

be displayed.

ˇ Select SETUP using the ▲/▼ button.
¨ Select MANUAL PROGRAM using the ▲/▼ button

and then press the

√ button.

ˆ Select FINE TUNE using the ▲/▼ button and then

press the

œ/√ button to fine tune.

If you are unable to fine-tune a channel, check
that the SYSTEM settings are correct.

Ø Select STORE using the ▲/▼ button and then

press the

√ button.

∏ Press the EXIT button to exit the menu.

When the Picture Quality is Poor or Unstable

Selecting the Picture Status

ΠUsing the PROG buttons

Press the

PROG ▲/▼ buttons to change channels.
You will see all the channels that the TV has
memorised.(The TV must have memorised at least
three channels.)

´ Using the NUMBER buttons

-To change to single-digit channels(0~9) faster,

press “0” before the single digit.
Example: For channel 4, press “0”, then “4”.

-To select a channel over 10, press the -/-- button
first.

Example: For channel 42, press “-/--”, then “4”,
then “2”.

ˇ Using the Previous Channel

Press the

PRE button on the remote control.

The TV changed to the last channels to the last
channel you were watching.

Changing Channel

MENU

PICTURE

System
Fine Tune
Program NO.
Child Lock
Store
Search

œ
œ
œ
œ
œ

LP

0
1

OK

--

œ

√

√
√
√
√
√

PCFUNCTIONSETUPSOUND

Move PreviousAdjust Exit

MENU

Status
Contrast
Brightness
Sharpness
Color

œ

Standard

√

PCFUNCTIONSETUPSOUND

Move PreviousAdjust Exit

PICTURE