VOV VHS-20CT Instruction Manual

EN

HEATING

CONVECTION HEATER

Model: VHS-20CT

Instruction manual

230V~50Hz 750W/1250W/2000W

READ AND RETAIN THESE INSTRUCTIONS FOR FUTURE REFERENCE

GENERAL SAFETY

 DO NOT COVER, RESTRICT AIR INLET/OUT OR USE TO DRY CLOTHES.
 DO NOT USE WITHOUT FEET ATTACHED.
 ONLY USE IN THE UPRIGHT POSITION ON A FLAT LEVEL SURFACE.
 THE SURFACE OF THIS FAN HEATER IS NOT CLOSELY SUPERVISE ANY CHILDREN AND PETS

IN USING.

 DO NOT USE FAN HEATER NEAR FLAMMABLE OR HEAT SENSITIVE ITEMS.
 DO NOT POSITION IN POINT OF OR UNDER POWER SOCKETS, SHELVING OR OTHER

OBSTRUCTIONS TO AIRFLOW.

ELECTRICAL SAFETY

 FOR INDOOR USE ONLY.
 SWITCH OFF AND UNPLUG WHEN NOT IN USE.
 DO NOT FULL THE HEATER ALONG THE CORD OR USE IF DAMAGED.
 DO NOT USE HEATER IN HUMID OR WET ENVIROMENTS.
 IF THE SUPPLY CORD IS DAMAGED IT MUST BE REPLACED BY AN ELECTRICAL OR

SIMILARLY QUALIFIED PERSON TO AVOID HAZARD.

ASSEMBLY

 Carefully turn the radiator on it’s side to fit the feet.
 Position each feet as shown in fig 1. and secure using the self tapping screws provided.
 Two screws are required for each feet and this unit must not be used without the feel firmly attached.

TO USE

 Turn the heater to the “OFF” position before plugging in.
 The operating temperature is selected by a combination of the heater switches and thermostat. The hottest

setting will be when the heater switches are both on and the thermostat is turned to “Maximum”.

 To determine the correct working temperature for your conditions, turn the heater to “High” and the

thermostat to “Maximum” when the room has reached the required temperature turn the thermostat slowly
to the left until the temperature is off. The temperature will now be kept constant.

 If you want to lower the operating temperature select the one of the heater switch only and repeat the above

procedure.

 The heater is fitted with an automatic cutout in the event that it overheats. If is this activates, turn the heater

to the off position and unplug. Allow the heater to cool and remove anything restricting the airflow before
using the heater again. If the automatic cut out operates repeatedly contact a quantified electrician for
advice.

NOTES

 For maximum benefit, closing windows and door when the heater is open
 Do not cover the ventilation holes as this will cause overheating and will activate the cut out.

CLEANING AND MAINTENANCE

To maximum the efficiency of the heater cleans regularly.

 Switch power switches to “OFF” position, unplug and allow the heater to cool.
 Wipe surfaces with a soft cloth. Do not use detergent or abrasives as this with scratch the surface.
 Ensure the intake grills free front dust, as this will reduce the airflow. Light accumulated dust can be

removed with soft cloth or vacuum cleaner.

 Allow surface to fully dry before using the heater again.

WALL MOUNTING

The heater is supplied with 2 pairs of bracket for wall mounting when required. Two holes are to be drilled in
the wall at a spacing of 418mm horizontally for fixing the upper bracket but the lower bracket are to be secured
to the corner of the base of the heater by using the holes originally meant for fixing the two feet. If necessary,
these two lower brackets can also be fixed to the wall.

MAXIMUM THE LIFE OF YOUR HEATER

 Avoid knocking or scratching the heater.
 Do not in dusty environment.
 When not in use cover heater and store in clean, cool and dry area.

According to Waste of Electrical and Electronic Equipment (WEEE) directive, WEEE should be
separately collected and treated. If at any time in future you need to dispose of this product please do
NOT dispose of this product with household waste. Please send this product to WEEE collecting points
where available.

SK

HEATING

KONVEKTOR

Model: VHS-20CT

Návod na použitie