Mounting Instructions and Operating Manual
Remote Control S for Automatic Charger No. 2075
Suitable for
Automatic Chargers of the Votronic "PB..." and "Vac..." Series as well as
Charging Converter Series "VCC...." with galvanic isolation
provided with 6p. tip jack "Remote Control".
Please read the mounting instructions and operating manual completely prior to starting
connection and start-up.
The remote control is designed for convenient and complete remote control of Votronic charging units being
installed at difficultly accessible locations near the battery.
Mounting:
If possible, the remote control should be installed at a location in the living space, which is easily accessible and well
visible. Choose an installation place in the furniture front being favourable to the contrast of the display (sun radiation).
The built-in depth is max. 16 mm, in order to be able to imbed the electronic system into the wall thickness of the
furniture.
The rear cut-out should be covered with non-conducting material (e. g. plywood, thickness: 3 mm, plastic plate or similar)
to protect the electronic system efficiently and to be able to use the loading area being eventually created behind. The
clear with of the cut-out should be at least 53 x 38 mm to ensure a safe alignment of the unit front.
The delivered connection cable is to be plugged-in and to be led to the automatic charger prior to the final installation of
the remote control.
Verify after installation, if any short-circuit of the electronic system by other cables and the vehicle ground are excluded
and connect the unit to the charger by inserting it into the tip jack "Remote Control".
An extension of the cable is possible with the plug in control cable of 5 m length.
- 2 -
Start-up and Operation:
LED indicators:
The LEDs (light-emitting diodes) of the remote control ensure complete control of the charging procedure, since they
have the same functions as the light-emitting diodes at the charger.
The operating manual includes a detailed description of the individual functions of the light-emitting diodes.
Switch ON / OFF:
The function of the switch on the remote control is determined from the charger. Please read the effect of the switch in
the manual of the charger.
In some devices, the switch puts for example the charger to stand-by mode. The same switch enables Silent Run
Operation (reducation at night) for other devices.
Appropriate Application:
The use of the Remote Control S may only be in conjunction with a VOTRONIC Charger or a VOTRONIC
Charging Converter with 6p. tip jack "Remote Control".
Safety Instructions:
Please observe the safety instructions for the automatic charger, particularly the instructions
concerning the laying of cables, in the operating manual.
Technical Data:
Operating Voltage: 5 V DC of the charger
Dimensions: 85 x 47 mm
Assembly Dimension: 65 x 35 mm
Built-in Depth: max. 16 mm
Weight: 23 g
Declaration of Conformity:
In accordance with the provisions of Directives 2014/35/EU, 2014/30/EU, 2009/19/EC, this
product complies with the following standards or normative documents:
EN55014-1; EN55022 B; EN61000-6-1; EN61000-4-2; EN61000-4-3; EN61000-4-4;
EN62368-1; EN50498.
The product
must not be
disposed of in
the household
waste.
The product is RoHS compliant.
It complies with the directive
2011/65/EU for Reduction of
Hazardous Substances in electrical
and electronic equipment.
Delivery Scope:
Remote Control
Connection Cable being ready for connection, Length: 5 m
4 Fastening Screws
Drilling Jig
Mounting Instructions and Operating Manual
Available Accessories:
Control cable of 5 m length, Order No. 2005 (for further extension required)
Subject to misprints, errors and technical modification without notice.
Al l rights reserved, particularly the right of reproduction. Copyright VOTRONIC 07/18.
Made in Germany by VOTRONIC Electronic-Systeme GmbH & Co. KG, Johann-Friedrich-Diehm-Str. 10, D-36341 Lauterbach
Phone: +49 (0)6641/91173-0 Fax: +49 (0)6641/91173-20 E-mail: info@votronic.de Internet: www.votronic.de
Loading...