VOSTOK-EUROPE OS22, 6S21, 6S30, 6S11, YM26 Instruction Booklet

www.vostok-europe.com

I

II
III
IV

V
VI

02

03

WATER RESISTANCE ................................................................ 03

WATCH WITH OS22 6S30 MOVE MENT, , 6S21 AND 6S11 S ... 05

WATCH WITH MOVEMENTYM26 ............................................ 15

WATCH WITH MOVEMENTYM86 ........................................... 29

WATCH WITH 515.24 MOVEMENT .......................................... 3 4

WARRANTY ................................................................................ 74

CONTENTS OF THE BOOKLET

I

WATER RESISTANCE

The level of water resistance of your watch is directly
related to the security of the screw-in back cover, which
is factory sealed:
 Water resistant 5 ATM you can water your garden
and wash your car with water coming out of a hose.
 Water resistant 10 ATM (or 100 meters) you can swim
and dive (but not from a tower) and swim under water
but not scuba dive.

 Water resistant 20 ATM (or 200 meters) or Water
resistant 30 ATM (or 300 meters) you can swim under

water with scuba equipment.

Water resistant watches of 5 or more atmospheres are,
as a rule, equipped with screw-in watch crowns.
To settle hands, wind up the watch or change the
calendar setting you should unscrew the crown.

I

04

Recommendation: please have the water resistance
of your watch tested once every two years at your
servicecentre.

Caution: Do not manipulate the watch crown and
pushers underwater and even in conditions of high
level of humidity.

!

Attention: There is some humidity inside the watch

thus when the outside temperature is lower than
inside the watch, the inside of the glass may fog up
temporarily. This is not a failure. But if it keeps
fogging and doesn't clean up or water gets inside
the watch, repair is required.

!

Watches with OS22, 6S30, 6S21

and 6S11 movements

(Produced by Citizen Watch Co., Japan)

06

Pic.1

5

Chronograph Function:
Timing: up to 59 minutes 59 seconds. 1/20 sec

chronograph (OS22 ant 6S30 movements). Battery:
SR927W.

Displays and buttons of OS22 (Pic.1), 6S30 (Pic. 2),
6S21 (Pic. 3), 6S11 (Pic. 4) movements:

1. Second hand of the chronograph.

2. Minute hand.

3. Hour hand.

4. Minute hand of the chronograph.

5. Calendar window.

6. Second hand

7. 1/20 sec chronograph hand.

8. 24 hour hand.

A

B

II

N 1 2

8

4

7

1 2

08

Setting the time

1. Pull the crown out to the 2nd position so that the
second hand stops at ZERO position.

2. Turn the crown to set hour and minute hands.

3. When the crown is pushed back to the normal
position in synchronization with a time signal, small
second hand begins to run.

Setting the date

1. Pull the crown out to the 1st Click Position.

2. Turn the crown anticlockwise to set the date.

3. After the date has been set, push the crown back to
the normal position.

!

6

A

B

Pic.2

II

N

4

5

7

10

Using the chronograph

This chronograph is able to measure and display time in
1/20 second united up to maximum of 59 min 59 sec.
The 1/20 second chronograph hand keeps moving
continuously for 60 seconds (for OS22) or for 30 seconds
(for 6S30) after starting and then stops at ZERO position.
NOTE: The 1/20 hand is absent in 6S21 and 6S11
movements.

Measuring time with the chronograph:

1. Press button B to change the watch to the

chronograph mode. The second hand resets and stops at
the ZERO second position.

2. The chronograph can be started and stopped each
time button A is pressed. The chronograph 1/20 second
hand stops at the ZERO second position after 60 seconds
(for OS22) or after 30 seconds (for 6S30) after starting.

Pic.3

II

1 2

6

A

B

N

4

5

When button A is pressed to stop the chronograph, the
chronograph 1/20 second hand advances rapidly to
display the measured time.

3. Pressing button B resets the chronograph and all
hands return to their ZERO positions.

* Moving of the 1/20 sec chronograph hand is a demo
only. Actual 1/20 measurement will be shown when the
STOP button is pushed.
NOTE: The 1/20 hand is absent in 6S21 and 6S11
movements.

Chronograph reset (incl. after replacing battery)
This procedure should be performed when the
chronograph second hand and chronograph 1/20(1/1)
second hand does not return to the ZERO second
position after the chronograph has been reset, and
including after the battery has been replaced.

1. Pull the crown out to the 2nd Click Position.

2. Press button A to set the chronograph second hand
to the ZERO position.

A

B

N 1 2

Pic.4

12

II

6

4

5

14

3. Press button B to set the chronograph 1/20 second
hand to ZERO position.
The chronograph hands can be advanced rapidly by
continuously pressing button A or B.

4. Once the hands have been zeroed, reset the time and
return the crown to its normal position.

5. Press button B to check that the chronograph hands
are reset to the ZERO position.

!

Caution: Do not return crown to the normal position

while chronograph second hand and 1/20

chronograph second hand return to ZERO position.

Each hands stop on the way when crown are

returned to normal position and these positions are

recognized as ZERO position.

NOTE: The 1/20 hand is absent in 6S21 and 6S11
movements.

II

(Produced by S. EPSON, Japan)

Watch with YM26 movement

16

17

III III

17

18

19

24

27

28

18

19

III III

20

21

III III

22

23

III III

24

25

III III

26

27

III III

28

III

(Produced by S. EPSON, Japan)

Watch with YM86 movement

31

IV

32

33

IV IV

34

35

IV IV

36

37

IV IV

38

39

IV IV

40

41

IV IV

Watches with 515.24 movement

(Produced by RONDA AG, Switzerland)

42

IV

Function: Hours, minutes, seconds.
Second time zone indication at 24-hourscale.

Battery: SR920SW

Pos. N: Position of rest (watch running)
Pos. 1: Quick-change correction for date

The date can also be corrected during the day­changing phase between 10 pm and midnight. The
date of the following day has to be set, because no
automatic date change takes place at midnight.

 Pull the crown out to position 1 (watch still running).
 Turn the crown clockwise until the required date

appears.
 Push the crown back into position N.
Quick-change correction for 24-hour display

 Pull the crown out to position 1 (watch still running).
 Turn the crown anticlockwise until the desired time

appears.
 Push the crown back into position N.

N 1 2

Minute hand

12-hour hand

Calendar window

24-hour hand

44

V

Pos. 2: Setting the time

 Pull the crown out to position 2 (watch stopped).
 Turn the crown, until the current time is displayed

(remember the 24-hour cycle).
 Push the crown back into position N.

46

47

VI

WARRANTY

V

The manufacturer warranty period is valid for 24
months from the purchase date. In each country of sale
the legal, country-specific guarantee conditions apply.
The customer shall not have any claim under this
warranty if: the watch does not have this Users
Manual; the watch has been repaired by unauthorized
service centre or person; the watch is not used in
accordance with the instructions supplied in this
User´s Manual.
The Warranty does not cover the watch-case, crystal,
band, bracelet and packing. If hidden faults are
detected during the warranty period, the watch can be
repaired at the warranty watch service shop marked by
your local distributor.

The right for warranty service is provided by the
guarantee certificate attached to the given passport­booklet of your watch.
The claims on watch replacement or repayment are
satisfied upon submission of the certificate from the
guarantee service.

48

VI

INTERNATIONAL GUARANTEE

AGENCY

Production Number

Date of Purchase

(Model Number)

(Stores stamp)

Seller

(Signature)

(Name)

Repair Coupon Nr.

Model Nr.

Date

Signature

Repair Coupon Nr.

Model Nr.

Date

Signature

Repair Coupon Nr.

Model Nr.

Date

Signature

Repair Coupon Nr.

Model Nr.

Date

Signature

NOTES