Vosonic GV6200 User Manual

GV6200

User’s Guide

Rev.A

_______________________________________________________________________

 2008 Vosonic Technology Corporation. All right reserved.

Part Number: 845550002001

Dear Customer

Thank you for purchasing Vosonic GV6200.

1.Before using Vosonic GV6200, you will have to

----------------------------------------------------------------------

1-1. Make sure the memory card has already partition

or re-format again.

1-2. Check www.vosonic.com

to download the
update firmware that we offer new functions and
improved features.

Enjoy your GV6200

The Vosonic Team

2

CAUTION

Under no circumstances should you try to repair the system
yourself, as this will invalidate the warranty. Do not open the
system as there is risk of electrical shock.

FCC Certifications

This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to Part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against
harmful interference in a residential installation.
This equipment generates, uses and can radiate radio frequency
energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio
communications.
However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of the
following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit different from
that to which the receiver is connected.

• Consult the dealer or an experienced technician for help.

3

IMPORTANT WARRANTY INFORMATION

A

y To reduce the risk of fire or shock hazard, do not expose

this equipment to rain, any liquid or moisture.

y Vosonic shall have no obligation to repair, replace or refund

until the customer returns the defective product to Vosonic.

y The repairs and replacement service will not apply to

PRODUCT units that were misused, repaired without
authorization ort by other reasons beyond the range of
intended use.

y Any replacement product may be either new or like –new,

provided that it has functionality at least equal to that of the
product being replaced.

y Vosonic is not responsible for any data stored on returned

products, please backup any data prior to shipping the unit.

y The limited warranty for accessories (included battery ) is

only valid for 6 months from the date of purchasing..

ll OUT OF WARRANTY repairs maybe subject to a normal

y

repair fee. Please contact your dealer or Vosonic for current
charges.

Package Checklist

y Main unit
y Mounting Bracket
y English user's guide
y Mini 5 Pins USB Cable
y Composite (RCA Yellow) Video Cable
y Power Adapter (100-240V auto switched )

4

Specifications

1/3” color CMOS 1.3 Mega Pixel camera

Camera

Recording mode

Video Recording format

Support memory card

Digit display indicator

LED indicator

USB Interface USB 2.0

Video Output

Power Supplier 5V/2A DC IN

Dimensions 90 x 43 x 127mm (L x W x H)

70 degree field of view for camera and
motion detection

Motion detected recording
Continuing recording

Codec: MPEG-4
Format: MP4
Resolution: 640x480 Pixels
Frame Rate: 20~30 fps
* The frame rate is subject to the speed of

memory card

Secure Digital Card (SD)
SD High Capacity (SDHC)

Counting number of motion detected times
Error message
Operating status

Recording mode or stand-by mode
Error message

Composite Video output
NTSC & PAL

z Please visit our web site to download the most recent manual and software.

5

2. Overview of Panels & Keys

Error LED indicator

Status LED indicator

Video-Out Jack

Night Vision
IR LED x 8

Microphone

Battery Status

Camera Angle Adjuster

4-digit 7-segment display
Indicator (Counter)

DC Jack

Hanging Rail
(Track)

SD card slot

RESET

USB Port

6

keypad Function Description

A short press places the recording into loop mode.

Loop/Clear

Continuous-loop recording

Will disable to loop while recording

A long press will clear all the recording files.

( Data written to memory card will be all lost)

(See 5.4 )

Stop/Set

A short press will stop the recording and put the unit
in standby.

(Data written to memory card will not be lost)

A long press allows you to set the type of your

television broadcast standard. (PAL or NTSC)

Enter/Time

A short press to display the current time.
A long press will allows you to set the timer.

Camera Angle

Allows you to adjust camera head.

Adjuster

H/M/L Parameter for motion Detection

(see How to configure Motion Detection)

Video-Out Jack Before recording, use the video-out function on TV

screen to adjust the camera head.