Von Duprin 6226, 6226DS Installation Instructions Manual

*931241-00*

6226/6226DS

931241-00

Electric Strike, Double Door Closed Back Mortise or
Cylindrical Application

Installation Instructions

Notes: Deadbolt will not function with this strike.

1. For lock or device preparation, see their directions.

2. Prepare door for strike (see other side).

3. Wire strike (Figure 1). (Switches on 6226DS only.)

Wiring
for DC

supply

Wiring
for AC

supply

Check with factory for re applications.

SOLENOID POWER REQUIREMENTS

Yellow solenoid wires = 12 VDC, 0.57 A

Black solenoid wires = 24 VDC, 0.29 A

(also shown on strike label)

NOTE

!

DC input is

{

nonpolarized.

12 VAC SO-12 12 VDC
or
24 VAC SO-24 24 VDC

12 VDC

or

24 VDC

{

Use crimp

connectors to

splice wiring

to P1 leads

P1 J1A P1A

P1

SO-12 or SO-24

Figure 1

J1

4. Test strike: Apply solenoid power. Fail secure (FSE) lip unlocks.
Fail safe (FS) lip locks. Figure 1 shows status of switches.

5. Install strike with two #12-24 screws. Make sure clearance
between latch bolt and strike lip is 1/32” (Figure 2). If not,
uninstall strike, adjust (Figure 3), and reinstall.

6. If latch bolt does not extend far enough to actuate tripper,
install extension (Figure 4). (Tripper on 6226DS only.)

7. Test door: With strike unlocked, door opens
with latch bolt extended. When door closes,
latch bolt rides over strike lip.

Use crimp connectors to
splice
leads; insulate unused leads

S1

S2

1
2
3
4
5
6

wiring to P2

P2

Red (C)
Blue
Yellow
White (C)
Gray
Violet

Standard: 5 A, 30 VDC

Gold: 0.25 A, 30 VDC

Solenoid

P2

J2

S1

S2

Fail safe (FS)J2Fail secure (FSE)

depressed, strike lip closed and locked
(switches and tripper on 6226DS only)

1
2
3
4
5
6

J2

Switches shown with tripper

(monitors

}

tripper)

(monitors

}

strike lip)

SWITCH RATINGS

S1

S2

Latch bolt

Strike lip

1/32”

Top view;

faceplate not

shown for clarity

Figure 2

NOTE:
Static Strength Rating 1500 lb.
Dynamic Strength Rating 70ft.-lb.
Endurance Rating 250,000 c.

A

To adjust strike,
loosen screws A, B,
and C and move
backbox sideways
as necessary

B

C

Figure 3

Customer Service

1-877-671-7011 www.allegion.com/us

Tripper

Figure 4

Extension

931241-00 Rev. 01/14-b

89/336/EEC

© Allegion 2014

Printed in U.S.A.

LHR shown

RHR opposite

RHR door

shown inactive

Reinforce for strike

attachment as required

#16 drill and

#12-24 tap

2 places

C door

L

C strike

L

Suggested

cutout

Door Preparation for Strike

1-7/16” minimum

clearance

backbox

assembly

Lock and strike C

C strike

L

and

latch bolt

9”

Strike

1-3/8”

4-1/2”

1-7/8”
minimum
clearance

1-1/2”

L

12” minimum

clearance

1-5/8”

1-7/8”

8-3/8”

4-3/16”

3-3/4”

6”

1-3/8”

11/16”

5/32”

Strike Dimensions and Required Clearances