Von Duprin 6211, 6211DS Installation Instructions Manual

*931227-00*

Notes:

1.

2.

3.

nlocks.

89/336/EEC

Wiring
for

Wiring
for

Fit

t.-lb.

6211/6211DS

931227-00

Electric Strike for Single Door Mortise or Cylindrical Application

Installation Instructions

Deadbolt will not function with this strike.
Check with factory for retrofit applications.

For lock or device preparation, see their directions.

Prepare frame for strike (see other side).

Wire strike (Figure 1). (Switches on 6211DS only.)

SOLENOID POWER REQUIREMENTS

Yellow solenoid wires: 12 VDC, 0.57 A

Black solenoid wires: 24 VDC, 0.29 A

(also shown on strike label)

DC

supply

AC

supply

Use crimp

connectors to

splice field wiring

to P1 leads

DC input is

{

nonpolarized

12 VAC SO-12 12 VDC
or
24 VAC SO-24 24 VDC

{

NOTE

P1 J1AP1A

12 VDC

or

24 VDC

P1

SO-12 or SO-24

J1

Solenoid

4. Install insert for auxiliary bolt operation (Figure 2).

5. Test strike: Apply solenoid power. Fail secure (FSE) lip u

Fail safe (FS) lip locks. Figure 1 shows status of switches.

6. Install strike with two #12-24 screws. Make sure clearance

between latch bolt and strike lip is 1/32” (Figure 3). If not,
uninstall strike, adjust (Figure 4), and reinstall.

7. If latch bolt does not extend far enough to actuate tripper,

install extension (Figure 5). (Tripper on 6211DS only.)

8. Test door: With strike unlocked, door opens with latch bolt

extended. When door closes, latch bolt rides over strike lip.

J2 P2

S1

S2

Fail safe (FS)J2Fail secure (FSE)

depressed, strike lip closed and locked
(switches and tripper on 6211DS only)

1
2
3
4
5
6

J2

Switches hown with tripper

Use crimp connectors to
splice field wiring to P2
leads; insulate unused leads

S1

S2

1
2
3
4
5
6

P2

Red (C)
Blue
Yellow
White (C)

Gray
Violet

SWITCH RATINGS

Standard: 5 A, 30 VDC

Gold: 0.25 A, 30 VDC

}

}

Figure 1

S1

(monitors

tripper)

S2

(monitors

strike lip)

hook on insert

into notch on

faceplate

Alternate insert

Figure 2

position

Latch bolt

Strike lip

1/32”

Top view;

faceplate not

shown for clarity

Figure 3

To adjust strike, loosen screws
A, B, and
backbox sideways as
necessary

A

For more
adjustment,
move
screw A
to hole D

C and move

D

B

C

Figure 4

NOTE:
Static Strength Rating 1500 lb.
Dynamic Strength Rating 70f
Endurance Rating 250,000 c.

Extension

Tripper

Figure 5

4-7/8”

4-7/8”

minimum

4-1/8”

3/8”

LHR shown

RHR opposite

C lock and strike

L

5/8”

1-1/4”

1-15/32”

3/4”

3-3/8”

C strike

L

Suggested cutout

11/32” maximum

#16 drill and #12-24 tap 2 places

Reinforce for strike attachment as required

Frame Preparation for Strike

1-1/4”

2-7/16”

C lock and strike

L

5/8”

1-1/8”

2-1/16”

4-1/8”

2” minimum

clearance

Strike

backbox

assembly

3-3/8”

C strike

L

1-21/32” minimum clearance

1-11/16”

12”

clearance

1-1/4”

Strike Dimensions and Required Clearances

Customer Service

1-877-671-7011 www.allegion.com

1/8”

6”

© Allegion 2014

Printed in U.S.A.

931227-00 Rev. 01/14-c