Voltronic Power 6K, 10K User Manual

6K/10K Online UPS

Uninterruptible Power Supply System

Version: 1.02

User Manual

Please comply with all warnings and operating

instructions in this manual strictly. Save this

manual properly and read carefully the following

instructions before installing the unit. Do not

operate this unit before reading through all

safety information and operating instructions

carefully.

Table of Contents

1. SAFETY AND EMC INSTRUCTIONS ................................................................................................. 1

1-1. TRANSPORTATION AND STORAGE ............................................................................................................... 1

1-2. PREPARATION ....................................................................................................................................... 1

1-3. INSTALLATION ...................................................................................................................................... 1

1-4. CONNECTION WARNINGS ............................................................................................................... 2

1-5. OPERATION ......................................................................................................................................... 3

1-6. STANDARDS ......................................................................................................................................... 3

2. INSTALLATION AND OPERATION .................................................................................................. 4

2-1. UNPACKING AND INSPECTION ................................................................................................................... 4

2-2. REAR PANEL VIEW................................................................................................................................. 4

2-3. SINGLE UPS INSTALLATION ..................................................................................................................... 5

2-4. SOFTWARE INSTALLATION ....................................................................................................................... 7

3. OPERATIONS .................................................................................................................................. 8

3-1. BUTTON OPERATION .............................................................................................................................. 8

3-2. LED INDICATORS AND LCD PANEL ............................................................................................................ 8

3-3. AUDIBLE ALARM.................................................................................................................................. 10

3-4. SINGLE UPS OPERATION ...................................................................................................................... 10

3-5. ABBREVIATION MEANING IN LCD DISPLAY ................................................................................................. 13

3-6. LCD SETTING .................................................................................................................................... 13

3-7. OPERATING MODE/STATUS DESCRIPTION ................................................................................................. 18

3-8. FAULT CODE ...................................................................................................................................... 20

3-9. WARNING INDICATOR .......................................................................................................................... 20

4. TROUBLE SHOOTING ................................................................................................................... 21

5. STORAGE AND MAINTENANCE ..................................................................................................... 22

5-1. STORAGE .......................................................................................................................................... 22

5-2. MAINTENANCE .................................................................................................................................... 22

6. SPECIFICATIONS ......................................................................................................................... 23

1

1. Safety and EMC instructions

Please read carefully the following user manual and the safety instructions before installing the unit or using
the unit!

1-1. Transportation and Storage

Please transport the UPS system only in the original package to protect against shock and

impact.

The UPS must be stored in the room where it is ventilated and dry.

1-2. Preparation

Condensation may occur if the UPS system is moved directly from cold to warm environment.
The UPS system must be absolutely dry before being installed. Please allow at least two hours for the
UPS system to acclimate the environment.

Do not install the UPS system near water or in moist environments.

Do not install the UPS system where it would be exposed to direct sunlight or nearby heater.

Do not block ventilation holes in the UPS housing.

1-3. Installation

Do not connect appliances or devices which would overload the UPS (e.g. big motor-type
equipment)) to the UPS output sockets or terminal.

Place cables in such a way that no one can step on or trip over them.

Do not block air vents in the housing of UPS. The UPS must be installed in a location with good
ventilation. Ensure enough space on each side for ventilation.

UPS has provided earthed terminal, in the final installed system configuration, equipotential
earth bonding to the external UPS battery cabinets.

The UPS can be installed only by qualified maintenance personnel.

An appropriate disconnect device as short-circuit backup protection should be provided in the
building wiring installation.

An integral single emergency switching device which prevents further supply to the load by the
UPS in any mode of operation should be provided in the building wiring installation.

Connect the earth before connecting to the building wiring terminal.

Installation and Wiring must be performed in accordance with the local electrical laws and
regulations.

2

1-4. Connection Warnings

• There is no standard backfeed protection inside, please isolate the UPS before working according to this

circuit. The isolation device must be able to carry the UPS input current.

• This UPS should be connected with TN earthing system.

• The power supply for this unit must be single-phase rated in accordance with the equipment nameplate.

It also must be suitably grounded.

• Use of this equipment in life support applications where failure of this equipment can reasonably be

expected to cause the failure of the life support equipment or to significantly affect its safety or

effectiveness is not recommended. Do not use this equipment in the presence of a flammable anesthetic

mixture with air, oxygen or nitrous oxide.

• Connect your UPS power module’s grounding terminal to a grounding electrode conductor.

• The UPS is connected to a DC energy source (battery). The output terminals may be live when the UPS

is not connected to an AC supply.

Before working on this circuit

- Isolate Uninterruptible Power System (UPS)

- Then check for Hazardous Voltage between all

terminals including the protective earth.

Risk of Voltage Backfeed

3

1-5. Operation

Do not disconnect the earth conductor cable on the UPS or the building wiring terminals in any
time since this would cancel the protective earth of the UPS system and of all connected loads.

The UPS system features its own, internal current source (batteries). The UPS output sockets or
output terminal blocks may be electrically live even if the UPS system is not connected to the building
wiring outlet.

In order to fully disconnect the UPS system, first press the “OFF” button and then disconnect the
mains.

Ensure that no liquid or other foreign objects can enter into the UPS system.

The UPS can be operated by any individuals with no previous experience.

1-6. Standards

* Safety

IEC/EN 62040-1

* EMI

Conducted Emission...............................:IEC/EN 62040-2

Category C3

Radiated Emission..................................:IEC/EN 62040-2

Category C3

*EMS

ESD.........................................................:IEC/EN 61000-4-2

Level 4

RS........................................................ ...:IEC/EN 61000-4-3

Level 3

EFT......................................................... :IEC/EN 61000-4-4

Level 4

SURGE................................................... :IEC/EN 61000-4-5

Level 4

CS........................................................... :IEC/EN 61000-4-6

Level 3

Power-frequency Magnetic field.............. :IEC/EN 61000-4-8

Level 4

Low Frequency Signals............................:IEC/EN 61000-2-2

Warning: This is a product for commercial and industrial application in the
second environment-installation restrictions or additional measures may be
needed to prevent disturbances.

4

2. Installation and Operation

There are two different types of online UPS: standard and long-run models. Please refer to the following
model table.

Model

Type

Model

Type

6K

Standard

model

6KL

Long-run

model

10K

Standard

model

10KL

Long-run

model

2-1. Unpacking and Inspection

Unpack the package and check the package contents. The shipping package contains:

● One UPS

● One user manual

● One monitoring software CD

● One RS-232 cable (option)

● One USB cable

● One battery cable (option)

NOTE: Before installation, please inspect the unit. Be sure that nothing inside the package is damaged
during transportation. Do not turn on the unit and notify the carrier and dealer immediately if there is any
damage or lacking of some parts. Please keep the original package in a safe place for future use.

2-2. Rear Panel View

Diagram1: 6K/10K Rear Panel

5

Diagram 2: 6KL/10KL Rear Panel Diagram 3: 6K(L)/10K(L) Input/Output Terminal

1. External battery connector

2. RS-232 communication port

3. Intelligent slot

4. USB communication

5. Emergency power off function connector (EPO connector)

6. Cooling fan

7. Input circuit breaker

8. Input/Output terminal (Refer to Diagram 3 for the details)

9. Maintenance bypass switch (option)

10. Output terminal

11. Grounding terminal

12. Utility input terminal

2-3. Single UPS Installation

Installation and wiring must be performed in accordance with the local electric laws/regulations and execute
the following instructions by professional personnel.

1) Make sure the mains wire and breakers in the building are in compliance with the standard of rated

capacity of UPS to avoid the hazards of electric shock or fire.

NOTE: Do not use the wall receptacle as the input power source for the UPS, as its rated current is less than
the UPS’s maximum input current. Otherwise the receptacle may be burned and destroyed.

2) Switch off the mains switch in the building before installation.

3) Turn off all the connected devices before connecting to the UPS.

4) Prepare wires based on the following table:

Model

Wiring spec (AWG)

Input

Output

Battery

Ground

6K

10

12 12

6KL

10

12

12

12

10K 8 8 8

10KL 8 8 8 8