Voltronic Power 1KVA, 2KVA Quick Manual

Quick Guide

LCD display (Please see the Operation section for
the details of LCD display.

Power switch

1. Output receptacles (4xschuko,

4xuniversal, 6xNEMA, 4xIndia or 4x
South Africa)

2. AC input

3. Circuit breaker

4. External battery connectors

5. Charge current selector: 10 A or 20

A

6. Operation mode selector: UPS or

Inverter

7. Solar panel terminal (option)

8. Solar charging indicator (option)

9. Charger fault indicator (option)

Inverter

1KVA/2KVA

1. Introduction

Thank you for purchasing the inverter. This simple solar inverter is designed to power your

home appliances or precious 3C electronics. It also can handle motor-type loads with high

surge power such as vacuums, small freezers, or drills. If the inverter is equipped with solar

charger, it becomes solar inverter which can convert solar power to battery power and provide

continuous power to connected equipment during night time.

2. Product Overview

Front View

Back View

V. 1.6

3. Important Safety Warning (SAVE THESE INSTRUCTIONS)

Model

Typical Amp.

1 meter (one-way)

Dia-mm

1K/2K

59 A

AWG 8

5.9

MODEL

1K

2K

CAPACITY

1000VA/600 W

2000VA/1200 W

INPUT

Voltage

110/120 VAC or 220/230 VAC

Voltage Range

75-150 VAC or 140-300 VAC

OUTPUT

Voltage Regulation (Batt. Mode)

+/-10%

Transfer Time

Typical 4-8 ms, 13ms max. (For PC)

40 ms max. (For Home Appliances)

Waveform

Pure Sine Wave

BATTERY

Battery Voltage

12 VDC

24 VDC

Floating Charge Voltage

13.5 VDC ± 0.5 VDC

27 VDC ± 1 VDC

Maximum AC Charge Current

10 A or 20 A (selectable)

SOLAR CHARGER (option)

Charging Current

50 A max.

Maximum PV Array Open Circuit Voltage

40 VDC

60 VDC

PHYSICAL

Dimension (DxWxH) mm

395 x 145 x 220

Net Weight (kgs)

10.1

14.8

Conventions used:
WARNING! Warnings identify conditions or practices that could result in personal injury;
CAUTION! Caution identify conditions or practices that could result in damaged to the

unit or other equipment connected.

Before using the inverter, please read all instructions and cautionary markings

on the unit, this manual and the batteries.

General Precaution-

Install the UPS in a protected area that is free of excessive dust and has adequate air flow.

Please place the UPS away from other units at least 20 cm to avoid interference. Do NOT

operate the UPS where the temperature and humidity is outside the specific limits. (Please

check the specs for the limitations.)

CAUTION! The unit is designed for indoor use. Do not expose this unit to rain, snow or

liquids of any type.

CAUTION! To reduce risk of injury, only use qualified batteries from qualified distributors or

manufacturers. Any unqualified batteries may cause damage and injury. Do NOT use old or

overdue batteries. Please check the battery type and date code before installation to avoid

damage and injury.

WARNING! It's very important for system safety and efficient operation to use appropriate

external battery cable. To reduce risk of injury, external battery cables should be UL certified

and rated for 75°C or higher. And do not use copper cables less than 10AWG. Below is the

external battery cable reference according to system requirements.

Table 1 Minimum Recommended Battery Cable Size versus Length

CAUTION! If a remote or automatic generator start system is used, disable the automatic

starting circuit or disconnect the generator to prevent accident during servicing.

4. Specifications

CAUTION! Do not disassemble the inverter. Contact with the qualified service center when

service or repair is required.
WARNING! Provide ventilation to outdoors from the battery compartment. The battery
enclosure should be designed to prevent accumulation and concentration of hydrogen gas at
the top of the compartment.
CAUTION! Use insulated tools to reduce the chance of short-circuit when installing or working
with the inverter, the batteries, or other equipments attached to this unit.
CAUTION! For battery installation and maintenance, read the battery manufacturer's
installation and maintenance instructions prior to operating.

Personnel Precaution -

CAUTION! Careful to reduce the risk or dropping a metal tool on the batteries. It could spark

or short circuit the batteries and could cause an explosion.
CAUTION! Remove personal metal items such as rings, bracelets, necklaces, and watches
when working with batteries. Batteries can produce a short circuit current high enough to
make metal melt, and could cause severe burns.

CAUTION! Avoid touching eyes while working near batteries.
CAUTION! Have plenty of fresh water and soap nearby in case battery acid contacts skin,

clothing, or eyes.

CAUTION! NEVER smoke or allow a spark or flame in vicinity of a battery.

5. Installation

NOTE: Before installation, please inspect the unit. Be sure that nothing inside the package is

damaged.

Connect to Utility and Charge

Plug in the AC input cord to the wall outlet. The unit will automatically charge the connected
external battery even though the unit is off.

Connect External Battery

Step 1 - Install a DC Breaker in a positive battery line. The rating of the DC Breaker must be
according to the inverter's battery current (50 Amp). Keep the DC breaker off. (see Fig. 1)
Step 2- Connect battery cables to the terminals of battery.
WARNING! Please use the appropriate battery cable. Please refer to Important Safety
Warnings Section for the details.

1) Single battery connection (Refer to Fig. 1): When using a single battery, its voltage
must be equal to the Nominal DC Voltage of the unit (see below Table 1).