VOLT POLSKA 500 E, 800 E, 1000 E, 1500 E, 3000 E PRODUCT MANUAL

WARRANTY CARD

DATE OF PURCHASE

SHIPPING ADDRESS

SIGNATURE / STAMP

DAMAGE DESCRIPTION

SERVICE COMMENTS

FILL IN IF NEEDEED
(*) Cross incorrect
I agree to pay the cost of inverter repair due to:
* expiration of the warranty period / * warranty void

PRODUCT MANUAL

PURE SINE WAVE ELECTRONIC INVERTERS

WITH UPS

sinusPRO E

Before proceeding with the repair, service will inform by phone about the exact costs of the repair.
Please attach a copy of the purchase document (receipt or invoice) to the complaint.
The full regulations of service repairs can be found on our website www.voltpolska.pl

[e-mail] (58) 341-05-06 | [e-mail] (58) 341-38-80 | [e-mail] (22) 100-42-99

VOLT POLSKA Sp. z o.o.

ul. Grunwaldzka 76

81-771 Sopot

www.voltpolska.pl

9

[e-mail] (58) 341-05-06 | [e-mail] (58) 341-38-80 | [e-mail] (22) 100-42-99

1

INTRODUCTION

FIRST TIME START-UP

Thank you for purchasing UPS from sinusPRO E series. Please read this user
manual before starting the device.

Inverter characteristics

ź One device with built-in DC / AC converter, an uninterruptible power supply unit and an automatic battery

charger

ź Toroidal transformer used in the converter ensures high efficiency and low idling current. The device is

much more energy-efficient than older constructions that used E-type transformers

ź Fast 32-bit microprocessor ensures accurate and trouble-free operation
ź Intuitive and simple operation thanks to the color LED display, which informs about the current operating

status of the device (input and output voltage, battery capacity, charging, etc.)

ź Converter generates a pure sinusoidal voltage at the output, which makes it possible to work with

practically any type of load

ź High battery charging current (exact values in the table with technical specifications)
ź Possibility of changing charge current and switching off charger
ź Fast switching from mains supply to operating mode as a UPS enables uninterrupted operation of

connected devices

ź Intelligent control of the cooling fan, depending on the actual temperature of the device and the operating

status of the inverter

ź AC priority switch (network) / SOLAR (battery) (on some models)

STARTING-UP INVERTER

1. Open the carton and check that all components are included and the device is undamaged. Disconnect mains cable from the
device.

2. Connect battery properly to the device according to the correct polarity (red wire + / black wire -).

3. Start the device with the ON / OFF button (hold down 5s until you hear a beep) and connect the plug to the mains socket.

4. Change the mains charger switch to the "I" position to start charging the battery and select AC PRIORITY.

5. Connect all devices that you want to use with the power supply, make sure they are turned off and turn them on one by one after
connecting.

6. On models with built-in priority switch, after connecting the regulator, select the SOLAR PRIORITY option.

SWITCHING-OFF THE INVERTER

1. Turn off one by one, all the devices connected to the inverter.

2. Change the charger switch to the "0" position to stop the battery charging process.

3. Hold down the ON / OFF button for 3 seconds to disconnect the inverter output.

4. Disconnect mains plug from the network.

5. Disconnect battery from the inverter.

ATTENTION

1.Be careful when connecting the battery, the voltage generated when reverse polarity happen can damage the inverter.

2. Do not overload the device above its nominal power. When connecting refrigerators, freezers and other induction appliances /
consuming more power on start-up, remember not to exceed 30% of the total power rating of the UPS.

3. Do not connect the device on the outdoors, avoid contact with water.

4. Remember to install the power supply in the right place, with access to fresh air and a minimum distance of 30 cm from each side
of the housing.

5. If you notice an incorrect operation / damage to the inverter, contact the manufacturer's service department.

6. If you want to test the device please do not unplug inverter from the mains. Instead turn off mains RCD switch in building to
observe proper work of the device. By unpluggin inverter from the mains, neutral - "zero" is cut off from the inverter, which can cause
incorrect work of the inverter.

[e-mail] (58) 341-05-06 | [e-mail] (58) 341-38-80 | [e-mail] (22) 100-42-99

2

[e-mail] (58) 341-05-06 | [e-mail] (58) 341-38-80 | [e-mail] (22) 100-42-99

3