1
2
3
1
2
3
I
J
K
E
F
H
G
D
A
B
C
U 1015
Keep both cover flaps open and cross reference pictures
with text where necessary.
Tools for your Vacuum Cleaner
C
Dust bags
C
Telescopic tube
D
Swivel hose and handle with manual suction control
B
Combination carpet / hard floor nozzle
G
Narrow crevice nozzle
H
Upholstery nozzle
Ensuring your safety
The cleaner is for domestic use only and has been designed to
ensure maximum safety and performance. Please follow these
simple precautions:
L
The cleaner is double-insulated so it must not
be earthed
M
The cleaner is only to be used by adults. Young
children or infirm persons should be supervised to
ensure that they do not play with the appliance
N
Always store in a dry place
O
Do not use to pick up liquids
P
Avoid sharp objects
Q
Do not pick up hot cinders or lighted cigarette ends
R
Do not use near flammable gases
S
Avoid tugging on the mains cable and check cable
regularly for damage
T
Note: Do not use cleaner with a damaged cable. If
damaged the cable should be replaced at a Service
Centre
U
The plug must be removed from the socket-outlet
before cleaning or maintaining the appliance
W
All service and repairs must be carried out by
authorised service staff
Getting Started
•
Check the dust bag is in place.
•
Insert the hose until the catches click to engage.
(Press catches inwards to release).
•
Attach tubes to the hose handle and floor
nozzle by pushing and twisting together
(Twist and pull apart to dismantle).
•
Extend the cable and connect to mains. The cleaner is
fitted with cable rewind, ensure cable is not twisted before
use (To rewind cable press symbol on handle. Note:
Please hold the plug to prevent it striking you or the
machine).
•
Press the On/Off button to activate the cleaner.
•
Suction can be regulated on the hose handle by
opening/closing the aperture.
Your Vacuum Cleaner features
AXMains cable
B
Y
Cable rewind button
C
i
On/off button
D
D
Multifunction handle
E
F
Cover release catch for dust bag compartment
F
e
Hose connection
G
A
Carrying Handle
H
G
Accessory compartment (for narrow crevice nozzle
and upholstery nozzle)
I
H
Storage slot for floor nozzle and extention tubes when
in use
J
I
Storage slot for floor nozzle and extention tubes when
not in use
1015
Getting the best results
k
Carpets: Use the floor nozzle with the lever in
this position
J
Hard floors: Use the floor nozzle with the lever in
this position
To avoid blockages and maintain suction efficiency, the
floor nozzles should be cleaned regularly using the
hose handle.
p
Loose rugs/curtains/lightweight fabrics: Reduce the
suction power. Use the floor nozzle for loose rugs and
the upholstery nozzle for curtains, cushions etc.
r
Confined areas: Use the crevice nozzle for crevices,
corners and radiators.
Dust bag indicator and changing the dust bag
For peak performance the dust bag must be changed
when full. Check the dust bag regularly and replace
when necessary.
To change the dust bag:
A Release catch and remove lid. Before removing the
dust bag, bend the tab into the hole to prevent dust
escaping.
B Remove the dust bag.
C Insert new dust bag by sliding the bag slots into the
holder. Close lid.
We recommend the dust bag is changed:
*
after using a carpet cleaning powder
*
if there is a bad smell from the cleaner, then you
should also change the filter
Dust bag safety device
To avoid damaging the cleaner, do not use it without a
dust bag. A safety device is fitted which prevents the
cover closing without a dust bag. Do not attempt to
force cover shut.
Changing/Cleaning the filters
There are two filters inside your cleaner. Never use the
cleaner without the filters in place.
To clean Motor Protection filter:
The Motor Protection filter should be cleaned when
dirty.
D) Release catch, remove lid and filter.
E) Wash filter in warm water.
F) Allow to dry and re-insert clean filter. Close lid.
To change Micro filter:
The Micro filter should be changed every fifth dust bag.
G) Release catch, open the filter cover and
remove filter.
H) Insert new filter and close cover.
Troubleshooting
1. Power: If the electric power does not come on,
disconnect from mains and check plugs, cable and
fuses where appropriate.
2. Blockages/dirty filters: The cleaner may switch
itself off in the event of a severe blockage or
excessively dirty filter(s). In such cases, disconnect
from mains and allow to cool for 20-30 minutes.
Clear blockage and/or replace filter(s) and restart. The
clearing of blocked hoses is not covered by the
guarantee.
3. Water: If water is sucked into the cleaner the motor
must be changed at a Service Centre.
For healthier homes
Thank you for choosing a Volta Rolfy. To ensure total satisfaction, read
this Instruction book carefully. Retain for reference.
ANY PROBLEMS?
DON’T TAKE IT
BACK TO THE SHOP
Something missing?
Don’t understand
We are only
a telephone
call away.
the instructions?
Need more help?
CUSTOMER HELPLINE
1 300 369 333
050 873 0730
(Local call cost Australia wide)
(Free call New Zealand wide)
2190516-38
Loading...