Volt VFL-40-MS-LI-ABZ Series Installation Instructions Manual
INSTALLATION INSTRUCTIONS
VOLT® Line Voltage Landscape Lighting
VOLT® Floodlight with Motion Sensor
VFL-40XX-MS-LI-ABZ
Help Hotline:
1-813-978-3700 • Mon-Fri 8am-8pm • Sat-Sun 10am - 6pm (EST)
Specications and product details subject to change without notice.
© Copyright 2019, VOLT® Lighting, Lutz FL USA 33549 • All rights reserved.
customersupport@voltlighting.com • 813.978.3700
- 1 -
INSTALLATION INSTRUCTIONS
VOLT® Floodlight with Motion Sensor
VFL-40XX-MS-LI-ABZ
Important: Please Read Before Installation
!
1. This LED Floodlight uses the latest in solid state lighting technology for
long life, low maintenance, and high efciency.
2. The same as traditional HID lighting. There are two installation
methods, suitable for various occasion.
3. An internal power-factor-corrected switch-mode supply allows it to be
used from any nominal 100V-277V, 60Hz AC supply without any variation
in light output.
4. Suitable for use in the following locations:
a. Ambient Temp: -20~+40°C (-4~+104°F)
a. Wet Locations
Note: Save these instructions for future reference.
Package Contents
A. (1) Fixture Body
Products Model #
Model
10W Flood Light AC 120V >0.9 10W 0.1A
30W Flood Light AC 120V >0.9 30W 0.3A
50W Flood Light AC 120V >0.9 50W 0.45A
Input
Voltage
Power
Factor
Watt
Current
Input
Finish Mounting
Bronze
Powder
Coat
Bronze
Powder
Coat
Bronze
Powder
Coat
Yoke
Yoke
Yoke
Important Safety Instructions
!
To avoid the risk of re, explosion, or electric shock, this product should
be installed, inspected, and maintained by a qualied electrician only, in
accordance with all applicable electrical codes.
To avoid electric shock:
1. Be certain electrical power is OFF before and during installation and
maintenance.
2. Luminaire must be connected to a wiring system with an equipment
grounding conductor.
To avoid explosion:
1. Make sure the supply voltage is the same as the rated luminaire voltage.
2. Do not install where the marked operating temperatures exceed the
ignition temperature of the hazardous atmosphere.
3. Do not operate in ambient temperatures above those indicated on the
luminaire nameplate.
For supply connections use wire rated for at least 90°C (194°F)
Warning: the luminaire shall be installed by qualied electrician.
Product Dimensions
2.55”
2.15”
R0.15”
Ø0.85”
4.5”
3.5”
2.85”
4.25”
4.25”
3.45”
6”
10W Flood Light
www.voltlighting.com
- 2 -
customersupport@voltlighting.com • 813.978.3700
- 3 -
INSTALLATION INSTRUCTIONS
VOLT® Floodlight with Motion Sensor
VFL-40XX-MS-LI-ABZ
Product Dimensions
R0.175”
2.85”
7.35”
Place Marks for Wall Anchor Bolts
1
Wall
Mark
Hold the yoke mount to your
desired mounting surface.
Place a mark on the wall using
the holes of the mount. These
marks will be used for the wall
anchors.
Ø0.85”
R0.2”
Ø0.85”
3”
5”
5”
6.85”
4.25”
5”
8.5”
30W Flood Light
2.85”
4.25”
8.25”
10”
8.85”
11.35”
9.35”
Yoke Mount
Install Wall Anchors
2
Hole
Wall Anchors
Wall
Fixture
Drill the holes for the wall anchors
using the marks on the wall. Insert
the wall anchors into the drilled
holes. Tighten the hex nuts on the
bolts until they are secure to the
wall.
5.85”
9.75”
50W Flood Light
www.voltlighting.com
- 4 -
customersupport@voltlighting.com • 813.978.3700
- 5 -
Loading...