Volt VAL-2100-0-BBZ, VAL-180-X-BXX, VAC-ZWM7-BBZ, VAL-180 BXX Series Installation Instructions Manual
INSTALLATION INSTRUCTIONS
VOLT® Low Voltage Landscape Lighting
VOLT® Top Dog with Integrated Hub Top
VAL-2100-0-BBZ (includes part# VAL-180-X-BXX & VAC-ZWM7-BBZ)
Help Hotline:
1-813-978-3700 • Mon-Fri 8am-8pm • Sat-Sun 10am - 6pm (EST)
Specications and product details subject to change without notice.
© Copyright 2019, VOLT® Lighting, Lutz FL USA 33549 • All rights reserved.
customersupport@voltlighting.com • 813.978.3700
- 1 -
INSTALLATION INSTRUCTIONS
VOLT® Top Dog with Integrated Hub Top
VAL-2100-0-BBZ (includes part# VAL-180-X-BXX & VAC-ZWM7-BBZ)
Important: Please Read Before Installation
!
This luminaire is intended for installation in accordance with local codes
and the National Electric Code (NEC). Failure to adhere to these codes and
instructions may result in serious injury, property damage and void the
warranty.
These instructions do not intend to cover all variations in installation,
operation maintenance or mounting situations.
1. Make sure the power is turned OFF before installing or servicing this
luminaire.
2. WARNING: risk of electrical shock. Install all luminaires 10 feet (3.05M)
or more from pool, spa or fountain.
3. This luminaire is intended to be used only with a power supply
(transformer) rated maximum of 300 watts (25 AMPS) at 15 volts.
4. Wiring connections must be made with UL listed wire connectors that are
suitable for outdoor use.
5. Position the low voltage wire and wire connector so that it is located
within 6 inches (15.2 cm) from a building structure, a luminaire or
tting.
6. The main low voltage cable is intended for shallow burial - less than 6
inches (152 mm).
Important Safety Instructions
!
INSTRUCTIONS PERTAINING TO A RISK OF FIRE, OR INJURY TO PERSONS
Lighted lamp is HOT!
WARNING – To reduce the risk of FIRE OR INJURY TO PERSONS.
1. Turn off/unplug and allow to cool before replacing lamp.
2. Lamp gets HOT quickly! Contact only switch/plug when turning on.
3. Do not touch the hot lens, guard or enclosure.
4. Keep lamp away from materials that may burn.
5. Do not touch lamp at any time. Use a soft cloth. Oil from skin may
damage lamp.
6. Do not operate the luminaire tting with a missing or damaged shield.
SAVE THESE INSTRUCTIONS
www.voltlighting.com
- 2 -
Package Contents
1”
0.75”
2.83”
2.3”
2.5”
5.5”-7.5”
A. (1) Fixture Body
Product Dimensions
There are three types of mounts that are sold separately for this xture;
the Stake Mount, Surface Mount and Tripod Mount.
customersupport@voltlighting.com • 813.978.3700
- 3 -
INSTALLATION INSTRUCTIONS
Option1: Stake Mount
Wire Connection
1
Connectors
VOLT® Top Dog with Integrated Hub Top
VAL-2100-0-BBZ (includes part# VAL-180-X-BXX & VAC-ZWM7-BBZ)
Integrated Hub Top
Fixture Wires
Main Supply Wires
Stake Mount
Main Supply Wire
Continuation
Insert the main supply wire continuation (if needed) and the main
supply wire up through the bottom of the stake mount and strip the
ends of both sets of supply wires.
Attach the xture wires and both sets of the main supply wires to their
correct connectors in the integrated hub top.
Once the wires are installed properly, thread the integrated hub top
back onto the stake mount and hand tighten until snug.
Install Stake
2
Board
Stake
Determine the desired location
for mounting the stake mount.
Hammer the stake into the
ground until ange of stake is
ush to grade. To avoid damage
to the stake, place a board on top
of the stake while hammering.
Main Supply Wire
Note: If the ground is hard and
the stake is difcult to install,
Ground
make a crosscut in the ground
using a at shovel.
Soil
www.voltlighting.com
- 4 -
Loading...