MEN-9632
Installation
Guide
www.volktek.com
Copyright © 2014 Volktek Corporation
Installation Guide for MEN-9632
Copyright © 2014 Volktek Corporation
All rights reserved. No part of this publication may be reproduced, stored in a
retrieval system, or transmitted in any form or by any means, whether electronic,
mechanical, photo copying, recording or otherwise, without the prior written
permission of the publisher.
2
Installation Guide for MEN-9632
Contents
Preface ..................................................................................................... 4
Related Documentation ............................................................................... 4
1. Hardware Installation .......................................................................... 5
1.1. Unpacking .............................................................................................. 5
1.2. Product Layout ........................................................................................ 6
1.3. Connecting AC/DC/Battery Power .............................................................. 7
1.4. Installing SFP modules and Fiber cables ..................................................... 8
1.5. LEDs ...................................................................................................... 9
2. Software Configuration ...................................................................... 11
2.1. Switch Access ....................................................................................... 11
2.1.1. Web-based management interface ..................................................... 11
2.1.2. Console .......................................................................................... 12
2.2. Configuration Backup/Restore ................................................................. 15
2.3. Reset to Default Configuration ................................................................ 16
2.4. Firmware Upgrade ................................................................................. 16
Support .................................................................................................. 17
3
Installation Guide for MEN-9632
Preface
This manual is the installation guide for MEN-9632 and contains the following
sections:
Hardware Installation
• Unpacking
• Product Layout
• Connecting AC/DC/Battery power
• Installing SFP modules and Fiber cable
• LEDs
Software Configuration
• Switch Access through
– Web-based management interface
– Console
• Configuration Backup/restore
• Reset to factory default configuration
• Firmware upgrade
Related Documentation
Support Notes
Configuration Guide
Troubleshooting Guide
FAQs
4
Hardware Installation
Package
Console Cable
AC Power cord
Rubber foot
User Manual CD
1. Hardware Installation
1.1. Unpacking
Open the package and carefully unpack the switch
The box should contain following items*:
One MEN-9632 – 24-slot 100FX/GbE SFP, 4-Gigabit Combo ports, L3 Managed
switch
One Console Cable – DB9 (RS232)
One AC power cord
One user manual cd
Accessories pack – Rack-mount rubber foot, bracket, screw etc.
* Contents of the package can be adjusted based on customer demand
5
Hardware Installation
A/C Power
LEDs
15V DC Jack
Battery connector
Console Port
Console Port
48V DC Input
1.2. Product Layout
Front View
The front panel of the MEN-9632 consists of 24-100FX/GbE SFP slots, 4-Gigabit
Combo ports, AC power socket, LEDs and Console port.
Rear View
The rear view panel of the MEN-9632 consists of 12V Battery connector and/or 48V
DC input
6
Hardware Installation
AC
Battery
• Connect battery to switch and check polarity
• Connect Positive (+) to Positive (+) and Negative (-) to Negative (-)
DC
LED indicating AC Power input
LED indicating Redundant Power input
LED indicating wrong polarity
when battery is connected in reverse
polarity before the switch is On
LED indicating correct polarity
1.3. Connecting AC/DC/Battery Power
The MEN-9632 supports 240V AC and 12V battery or 48V DC power supplies.
7
• Slide the SFP module into the selected SFP slot (Make sure SFP module is
aligned correctly with the SFP slot)
• Insert and slide the module into the SFP slot until it clicks into place
• Remove any rubber plugs that may be present in SFP module’s mouth
• Align the Fiber cable’s connector with SFP module’s mouth and insert the
connector
1.4. Installing SFP modules and Fiber cables
Steps to install SFP modules:
Hardware Installation
Steps to install Fiber cables:
8
Hardware Installation
• To pull the connector out, press the release clip and pull the connector from
SFP module
1.5. LEDs
The LEDs on the MEN-9632 are as below:
9
Unit LEDs
LED
Condition
Status
POST
On (Green)
Switch is ready and running Ok
Flashing (Green)
Switch is booting
Off
Switch is not ready or failed
PWR1
On (Green)
Power On
Off
Power Off or fail
PWR2
On (Green)
Power On
Off
Power Off or fail
ALARM
On (Red)
Alarm for over threshold of system
temperature or voltage
Flashing (Red)
Alarm for loop detection
Off
Switch is in normal condition
LNK/ACT
(1-24 Fiber Ports)
On (Green)
1000Mbps Ethernet link-up
On (Amber)
100Mbps Ethernet link-up
Flashing (Green)
Activity (receiving or transmitting data)
Off
Port disconnected or link failed
LNK
(25-28 Fiber Ports)
On (Green)
Link-up
Off
Port disconnected or link failed
ACT
(25-28 Fiber Ports)
Flashing (Green)
Activity (receiving or transmitting data)
1000
(25-28 Copper
Ports)
Flashing (Green)
1000Mbps
Off
10/100Mbps
LNK/ACT
(25-28 Copper
Ports)
On (Green)
Link-up
Flashing (Green)
Activity (receiving or transmitting data)
Off
Port disconnected or link failed
The LEDs on the MEN-9632 indicate the following:
Hardware Installation
10
Software Configuration
MEN-9632 Default settings:
IP address: 192. 168. 0. 254
Subnet mask: 255.255.255.0
Web Login: admin
Password: admin
2. Software Configuration
2.1. Switch Access
2.1.1. Web-based management interface
Steps to access the switch through web-based management interface:
• Set the IP address of your computer to 192.168.0.XXX
• Connect MEN-9632 to your computer
• Open your computer’s web browser
• Type http://192.168.0.254 in the address box to access the web
A login screen is displayed
• Login with default username and password
A web manager homepage appears as shown in the figure below:
11
Software Configuration
2.1.2. Console
Steps to access the switch through console port:
• Insert male pin of the console cable in Console port of the MEN-9632
• Connect DB-9 pin to your computer serial port
12
Software Configuration
Console login through putty:
After connecting console cable to MEN-9632 console port and your computer’s serial
port,
• Go to Device manager
• Scroll to ‘Ports’ USB Serial Port (COM#) Make a note of COM#
• Run ‘Putty’
• Type the COM# in serial line (e.g. COM5 as shown in the figure)
• Set the speed to 38400
• Click ‘Open’
A session is opened and displays the CLI as shown in the figure below to configure the
desired settings
13
Software Configuration
Console Login through Hyper Terminal:
Note: HyperTerminal is not an in-built feature in Windows Vista, 7 and 8. You can copy it
from Windows XP.
Use the following settings
14
2.2. Configuration Backup/Restore
Steps to backup and restore configuration file:
• Run TFTP server
• Set TFTP server IP and Gateway
(e.g. IP: 192.168.0.200 and Gateway: 255.255.255.0)
• Specify directory path as shown in figure below
Software Configuration
• Use the following command to backup (upload) configuration file
(e.g. configurationfile.bin)
• Use the following command to restore (download) configuration file
(e.g. configurationfile.bin)
15
Software Configuration
Factory default
configuration
2.3. Reset to Default Configuration
• Use the following command to reset the switch to its factory default
configuration settings
2.4. Firmware Upgrade
Steps to upgrade the firmware of the switch:
• Place firmware (FW) in root directory of the TFTP server
• Run TFTP server
• Use the following command to upgrade the firmware of the switch
(e.g. firmware file name: 9632-000-2.0.5.b7.fw)
16
Installation Guide for MEN-9632
Support
For any assistance with this product, please visit Support section of www.volktek.com
website. Also, you can contact us by email: support@volktek.com
17
Loading...