1
User Guide
model
Hybrid :VBAE-01000
Active : VBAE-02000
www.volfoni.com
2
3
Summary
1. PRODUCT OVERVIEW 4.
1.1 DESCRIPTION 4.
1.2 SET UP OF ARMS 5.
1.3 PACKAGING COMPOSITION 5.
2. EDGE RF FEATURES 6.
2.1 GENERAL SPECIFICATIONS 6.
2.2 TECHNICAL SPECIFICATION 6.
3. REQUIREMENTS 7.
3.3 ACTIVHUB
TM
RF50 OVERVIEW 7.
3.4 GENERAL SETUP 7.
4. USING YOUR EDGE
TM
RF 9.
4.1 ON/OFF AND AUTO OFF 9.
4.2 SWITCH BUTTON 9.
4.3 BATTERY 9.
4.3.1 BATTERY LEVEL 9.
4.3.1 BATTERY CHARGE 10.
5. SOFTWARE UPDATES 10.
6. VOLFONI LOADER - PARAMETERS 11.
7. TROUBLESHOOTING 12.
8. IMPORTANT SAFETY RECOMMENDATIONS 13.
9. WARRANTY 14.
10. REGULATIONS 14.
11. MORE INFORMATION AND CONTACTS 15.
4
5
1. REQUIREMENTS
To use your ActivEyes Pro in active 3D mode you
need a 3D device playing 3D content on a 3D
Display using compatible IR synchronization.
2. PRODUCT OVERVIEW
Your 3D Glasses System by Volfoni includes one pair
of ActivEyes Pro 3D glasses and one ActivMe Pro
electronic receiver. Your ActivEyes Pro glasses, when
connected to the ActivMe Pro, are compatible with
most 3D TV sets using IR signals to control 3D glasses.
The ActivMe Pro receiver can be recharged and
updated to new IR and RF 3D protocols via its USB
port.
If your ActivEyes Pro 3D Glasses are tted with Hybrid
ClearLenses, they will decode 3D from passive
displays too.
3. DESCRIPTION OF THE ACTIVEYES
The ActivEyes Pro eyewear includes:
1. Liquid Crystal shutter lens
2. Connection plug
If your 3D Display does not come with an IR emitter,
you may want to acquire one from its manufacturer,
or plug a Volfoni ActivHub RF50 to a 3D sync out
To use your ActivEyes Pro with hybrid lenses in passive
3D mode, you need a 3D device playing 3D content
on a 3D display using compatible circular light
polarization.
3D Content
Movie, sports...
Active 3D
display
IR Beam
3D Player
Computer, Blu-Ray...
Active 3D
display
3D Content
Movie, sports...
ActivHub
RF50
3D Player
Computer, Blu-Ray...
Passive 3D
display
3D Content
Movie, sports...
3D Player
Computer, Blu-Ray...
5.
9.
6.
3.
4.
10.
7.
8.
11.
1.
2.
The ActivMe electronic driver includes
3. Power selector [on-off ]
4. Function selector [1-2]
5. Action button [Press]
6. LED
7. IR window
8. Micro-USB computer plug
(charging and upgrading)
9. Micro-jack connection plug
for glasses
10. Holding clamp
11. Lanyard
6
7
4. QUICK START
To watch active displays using your ActivEyes System
in universal infra-red 3D mode :
1. Using the connection cable, plug the ActivEyes Pro
to the ActivMe Pro, and place the glasses on your
head.
2. Check that the “function” selector on the ActivMe
Pro is on “1”.
3. Switch the power on. The glasses should blink once
each eye to signal that the system is up and running.
4. As soon as the IR or RF signal is identied and
interpreted, the glasses go into 3D mode. You can
now attach the ActivMe Pro to the front of your
clothing or attach to the lanyard, making sure that
the IR window is not obscured.
To watch passive displays (for VBAE-01000 models
only) :
Simply wear your ActivEyes Pro. There’s no need to
plug or power on the ActivMe Pro.
5. CHARGING BATTERY
To charge the ActivMe Pro, plug it in using the
Micro-USB cable to any 5V USB power source (or
computer). The LED should go red until the battery
is fully charged, then the LED goes green, typically
after 2.5 hours. The battery is estimated to last 30
hours before needing a recharge. Your ActivMe can
operate while charging.
6. UPDATE YOUR ACTIVEYES PRO
Before using the ActivEyes Pro glasses, make sure
you have the latest version of software from our
website. For this purpose, please download the «
Volfoni Loader » software (http://www.volfoni.com/
en/services-support/download) and connect your
glasses to your computer. Then start the software and
follow the instructions below.
- choose the menu “SUPPORT”
- choose “Upgradable Software”
- download the application “VOLFONI LOADER”
- connect your computer to the μUSB connector on
ActivMe with the USB/μUSB cable
- press and hold the button of the ActivMe, and
switch ON the ActivMe
- the LED of the ActivMewill light red
- verify that the application recognizes your system
- once you are connected, press the button “Check
for updates”
- download the lastest version
8
9
7. VOLFONI LOADER - PARAMETERS
You can access to this part by clicking on
“parameter” in the menu “edit” when your glasses
are connected
3D Synchronisation :
- Normal : In this conguration the glasses will receive
a normal 3D synch
- Inverted : In this conguration the glasses will
receive a reverse 3D sync
- 2D Left : In this conguration the glasses will show
the 2D image left
- 2D Right : n this conguration the glasses will show
the 2D image right
RF Channels :
Choose which channels the glasses will receive on
this switch position (you have to choose the same
channel on your ActivHub RF50)
Dark Time :
Allows you to change the value of DarkTime
The slider allows you to adjust the value between
-4000 microseconds (better luminosity) and 4000
microseconds (better contrast). The value applied is
inscribed above the slider (0 in this example)
Delta Sync (μs) :
Modify the sync offset (between -2000 and 2000
microseconds). Default = 0.l
8. IR COMPATIBILITY
The ActivEyes Pro glasses are compatible with all
infra-red 3D sync
protocols currently available:
KONKA®
ARCELIK®
SHARP®
SONY® (*)
PANASONIC® (*)
LG®
MITSUBISHI®
SAMSUNG® (*)
NuVisionXPAND® (unencrypted)
HI-SENSE®
NVIDIA® (including “light boost”)
* Bluetooth® and Full HD3D™ not supported
New IR protocols entering the market will be
available on the Volfoni website via software
update. Please refer to part 6 of this user guide for
updating the software of the ActivEyes
9. RF compatibility
Using your ActivEyes Pro in RF 3D mode :
ActivMe Pro is compatible with ActivHub RF50. It’s a
proprietary signal.
10
11
9. TROUBLESHOOTING
PROBLEM SOLUTION
The jack plug may not
be all the way inserted
in the ActiveMe Pro or
in the glasses
Check the connection
jack
The IR signal is not
recognized
Check that your 3D
system
is emitting IR
The IR signal is obscured Make sure ActivMe
Pro is
facing the IR emitter
The IR signal is
scrambled by other
sources like direct
sunlight
Reduce external light
The ActivMe Pro battery
is discharged
Plug the USB cable
into a
power source and try
again
Your 3D display uses
an IR protocol not
compatible with
Activeyes Pro
Check www.volfoni.
com
for update
10. SPECIFICATIONS
ActivEyes Pro VPAE-02000 VPAE-01000
Lens technology ECB liquid
crystal
Hybrid ECB
Transmittance 35%
33%
Residual light 17%
16%
Contrast 200:1
200:1
Connector 4 points 2.5’’ jack
Weight 29g
ActivMe Pro (electronic driver) VPAE-03000
Receiver IR and RF
Connector µUSB and 4-points 2.5’’ jack
Power Battery type Lithium-ion
Operating time 30 hours
Operating
conditions
Operating 0° to 35° C
Storage -20° to 45° C
Relative
humidity
5% to 95%
Height 50 mm
Width 41mm
Depth 15mm
Weight 21 g
12
13
10. LED SIGNIFICANCE
- Flashing Green: Valid 3D signal detected
- Red: Battery recharge
- Flashing Green/Orange: Viewing 3D and
recharging simultaneously
10. IMPORTANT SAFETY
RECOMMENDATIONS
- The ActivEyes Pro 3D glasses are not suitable for
wear when playing sports, driving vehicles, operating
heavy machinery, or doing outdoor activities. It
should not be used as sunglasses (no UV protection)
- If you are unsure about your vision, take a test to
verify your ability to see stereoscopic 3D images.
- Do not sit too close to the screen when watching
3D images.
- Watching 3D may cause discomfort (such
as eye strain, altered vision, fatigue, nausea,
lightheadedness, dizziness, confusion, loss
of awareness, convulsions, cramps and/or
disorientation) for some people. Volfoni recommends
that you take regular breaks when watching
3D content or playing 3D video games until the
discomfort ends. If the discomfort persists, consult a
doctor.
- Certain types of TV images or video games that
contain ashing patterns of light may cause epilepsy
symptoms for some viewers.
If you or any member of your family has a history
of epilepsy, Volfoni strongly recommends that you
consult a physician before the use of this product.
- Be aware of young children, especially those
under six years old. Because their vision is still under
development, consult a doctor (such as pediatrician
or eye doctor) before allowing young children to
watch 3D.
- Not for children’s use without proper adult
supervision.
- If the product is broken, please keep broken pieces
away from mouth and eyes. Dispose of pieces
responsibly.
- Do not use 3D glasses in dangerous areas (such as
balconies and stairwells).
9. WARRANTY
Volfoni Group reserves the right to make changes in
the hardware, packaging or other documentation
without prior written notice. The ActivEyes Pro glasses
are a trademark of Volfoni Group. All trademarks are
the property of their respective companies.
The EDGE™ VR are warrantied. Please refer to your
order form to be aware of the warrantee terms.
The system should be returned in it original box with
original proof of purchase. Volfoni does not warrant
uninterrupted or error-free operation of the product.
10. REGULATIONS
European Union - Disposal information :
This symbol means that according to local laws
and regulations your product should be disposed of
separately from household waste. When this product
reaches the end of its life, take it to a collection point
designated by local authorities. Some collection
points accept products for free. The separate
collection and recycling of your product at the time
of disposal will help conserve natural resources and
ensure that it is recycled in a manner that protects
human health and the environment.
- This Class B digital apparatus complies with
Canadian ICES-003.
11 . PRECAUTION FOR USE - 3D
VIEWING GUIDE-LINES
- The 3D glasses need to synchronize by infrared
rays. For this operation to work well, be aware of the
following instructions:
- The ActivMe Pro has to face the 3D Sync
Transmitter.
- Remove all objects placed between the 3D glasses
and the 3D Sync Transmitter.
- Other infrared communication devices or lighting
equipment, residential heating equipment, etc...,
may interfere with the synchronization.
- Avoid watching 3D under uorescent lamp (5060HZ) or wavelength lamp. Sometimes this can cause
a small amount of screen ickering.
14
15
11. MORE INFORMATION AND
CONTACTS
For more information, please contact Volfoni.
support@volfoni.com
logistics@volfoni.com
www.volfoni.com
Distributed in France by VOLFONI SAS
29 rue Jean Jacques Rousseau 75001 Paris,
France
Distributed in Americas by VOLFONI Inc.
3450, Cahuenga Bd West, Unit 504, Los
Angeles, CA90068, USA
Distributed in Germany by VOLFONI GmbH
Erzgießereistraße 38, 80335 München,
GERMANY
Distributed in Spain by VOLFONI Iberia, S.L.
4, Ronda Guglielmo Marconi, 46980 Paterna
(Valencia), Spain
Distributed in China by VOLFONI Ltd
2101, Tower One, Lippo Center, 89,
Queensway, Hong Kong
14. CAUTION MAINTENANCE OF YOUR
GLASSES
- Protect the 3D system from direct sunlight, heat, or
water. Extreme conditions may alter the product’s
abilities.
- Do not drop or modify the electrical or mechanical
components of the 3D system.
- Do not apply force to the lenses of the 3D system.
- Do not bend the product.
- Use a clean soft cloth when cleaning the 3D glasses
to avoid scratching, especially on the lens surface.
- Always transport your 3D glasses in a rigid case
to avoid scratching the lenses and to prevent the
frames from breaking.
- Do not submerge the ActivEyes Pro glasses or the
ActivMe Pro IR receiver in water.
Loading...