VOKERA Syntesi e User Instructions
User
Instructions
THESE INSTRUCTIONS
TO BE RETAINED
BY USER
e
1
e
Contents
Page
Introduction Dear customer 1
Do’s and don’ts 1
Things you should know 1.1 Gas appliances 3
1.2 Electrical supply 3
1.3 Guarantee registration card 3
1.4 Benchmark log book 3
1.5 How does it work? 3
1.6 Additional features 3
1.7 Dimensions 3
1.8 Clearances 3
1.9 Filling valve 4
Getting started 2.1 Before switching on 4
2.2 Appliance controls 4
2.3 Lighting the boiler 4
How to… 3.1 Top-up the system 5
3.2 Reset the appliance 5
3.3 Understand the diagnostic fault codes 5
3.4 Shut down the system for short periods 5
3.5 Shut down the system for long periods 5
3.6 Care for the appliance 5
What if… 4.1 I suspect a gas leak 6
4.2 I frequently have to top-up the system 6
4.3 The status LED is flashing Red 6
4.4 The appliance is due its annual service 6
4.5 I need to call an engineer 6
Setting the Vokera…. Remote-control (RC05) 6
Mechanical clock 9
Digital clock 9
Dear Customer
Your “Syntesi e” boiler has been designed to meet and exceed the very latest standards in gas central heating
technology and if cared for, will give years of reliable use and efficiency. Please therefore take some time to read
these instructions carefully.
Do’s and Don’ts
● Do ensure that the system pressure is periodically checked
● Do ensure that you know how to isolate the appliance in an emergency
● Do ensure that you are familiar with the appliance controls
● Do ensure that your installer has completed the appliance log book
● Do not attempt to remove the appliance casing or gain internal access
● Do not hang clothes etc. over the appliance
● Do not forget to have the appliance serviced annually
● Do ensure that your installer or engineer uses only genuine Vokera spare parts
INTRODUCTION
2
e
1. Pressure gauge
2. Clock aperture
3. N/A
4. Hot Water temperature selector
5. Mode selector switch
6. Status LED
7. Digital display
8. Heating temperature selector
9. DHW request LED
Fig. 1
Fig. 2
INTRODUCTION
Filling valve
Filling Loop
Isolating valve
45 786
123
9
3
e
1.1 GAS APPLIANCES
Gas Safety (Installations and Use) Regulations.
In the interests of your safety and that of others it
is a legal requirement that all gas appliances are
installed and correctly maintained by a competent person and in accordance with the latest regulations.
1.2 ELECTRICAL SUPPLY
Please ensure that this appliance has been properly connected to the electrical supply by means
of a double pole isolator or un-switched socket,
and that the correct size of fuse (3 amp) has been
fitted.
WARNING:
THIS APPLIANCE MUST BE EARTHED!
1.3 GUARANTEE REGISTRATION CARD
Please take the time to fill out your guarantee
registration card. The completed warranty card
should be posted within 30 days of installation.
1.4
BENCHMARK
LOG BOOK
The
Benchmark
Log Book is supplied with your
boiler. This important document must be completed
during the installation/commissioning of your boiler.
All CORGI Registered Installers carry a CORGI
ID card and have a registration number. Both shoulf
be recorded in your
Benchmark
Log Book. You
can check your installer by calling CORGI direct
on 01256 372300. Failure to install and commission
the appliance in accordance with the
manufacturers instructions may invalidate the
warranty. This does not affect your statutory rights.
1.5 HOW DOES IT WORK?
Your
Syntesi e
boiler is a combined central
heating and hot water boiler. The
Syntesi e
supplies heated water to your radiators and
provides hot water when a hot water outlet is
opened.
Your
Syntesi e
boiler can be controlled by sev-
eral different types of controls such as:
● Integral time clock
● External time clock
● Vokera remote-control
● Programmable room thermostat
It’s therefore necessary to ensure that these instructions are read in conjunction with the instructions supplied with the relevant control.
The
Syntesi e
lights electronically and does not
have a pilot light.
In the unlikely event of a fault developing with
your boiler, the supply of gas to the burner will be
terminated automatically.
1.6 ADDITIONAL FEATURES
Your
Syntesi e
boiler includes some of the latest
features that have been designed to ensure continued safety and reliability of the appliance.
These include:
● appliance frost protection
● hot water pre-heat
1.7 DIMENSIONS
HEIGHT 820mm
WIDTH 400-500mm depending on model
DEPTH 355mm
1.8 CLEARANCES REQUIRED
ABOVE 150mm
BELOW 150mm
SIDES 12mm
FRONT 600mm
● pump, valve actuator & fan anti-block
● diagnostic fault codes
● LED status indicator
● digital display
FROST PROTECTION
Your
Syntesi e
boiler will automatically operate
to minimise the risk of frost damage to the boiler
itself. The frost protection device will be disabled
should the power supply to the boiler be disrupted.
HOT WATER PRE-HEAT
The
Syntesi
’s
pre-heat facility ensures that the
boiler responds quickly to any hot water requests.
PUMP, ACTUATOR, & FAN ANTI-BLOCK
When the boiler has not been used for more than
24 hours, the pump, fan & valve actuator, are energised for a few seconds to ensure that they does
not stick or jam. This function will be disabled
should the power supply to the boiler be disrupted.
DIAGNOSTIC FAULT CODES
In the unlikely event of a fault developing, the
boiler displays a unique fault code that helps identify where the fault lies.
LED STATUS INDICATOR
The Syntesi e is equipped with an LED status indicator that gives a visual indication of whether the
boiler is working normally or has developed a
fault.
DIGITAL DISPLAY
The digital display shows the current temperature of the hot water or heating outlet (depending on mode of operation). In addition, it also displays a unique fault code in the unlikely event of
the boiler malfunctioning.
THINGS YOU SHOULD KNOW
Loading...