VNS G-201 Passive 3D Processor Quick User Manual
G-201 Quick User Manual Document: G-201101
------------------------------------------------------------------------------------------------------------------------------------------------
1
Limited Warranty
This device is designed and tested to the highest standards and backed by a one year parts and labor warranty. Warranties are effective upon the
first delivery date to the end customer and are non-transferable. Warranty related repairs include parts and labor, but do not include repair of
faults resulting from user negligence, special modifications, abuse (mechanical damage), shipping damage, and/or other unusual damages. The
customer shall pay shipping charges when the unit is returned for repair. Manufacturer will pay shipping charges for return shipments to
customers.
Manufacturer does not assume responsibility for consequential damages, expenses or loss of revenue, inconvenience or interruption in operation
experienced by the customer. Warranty service shall not automatically extend the warranty period.
FCC/CE statement
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits
are designed to provide reasonable protection against harmful interference when the equipment is operated in a residential / commercial
environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the
instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause
harmful interference in which case the user will be required to correct the interference at his own expense.
G-201 Passive 3D Processor Quick User Manual
Thank you for choosing G-201 passive 3D processor. G-201 is an advanced dual
channel passive 3D processor with 10 bits high end scaler and Perfect Sync 3D RH/LH
synchronization algorithm. It is a professional grade passive 3D demultiplexer and pure
hardware video wall controller without geometry adjustment function. User needs to use
keystone or lens shift function to align the images from two projectors. No additional
video distributor, tool or computer is required for the setup.
Features
1. 2k x 1k (2048x1080) input and output
2. Support HDMI 1.4 standard 3D
formats from Blue Ray, game, PC…
3. DVI-I input port for the connection
with DVI, VGA & HDMI signals
4. Dual DVI-D output ports to support
DVI & HDMI connections
5. Embedded audio input and output
through HDMI connection
6. 10 bits scaler with high performance
de-interlace and scaling
7. 3D demultiplexer into RH/LH for
passive 3D display
8. Special algorithm for perfect RH/LH
synchronization in 3D mode
9. User friendly OSD and IR remote
control. No PC is required
10. Video wall function up to 15x15
matrix displays with pixel base
overlap adjustment
Brief specifications
1. Input: 1x DVI-I ( support VGA/DVI/HDM), up to 2048x1080
2. Output: 2x DVI-D (support DVI/HDMI), up to 2048x1080
3. Audio: In: HDMI, PC Jack, Out: HDMI, Analog PC Jack
4. Size: 303x157x36mm
5. Control: full function keypads, IR remote controller, RS232
G-201 Quick User Manual Document: G-201101
------------------------------------------------------------------------------------------------------------------------------------------------
2
Outlook and Functions
Help tips
1. Toggle on CH A/B keypad will circulate the OSD control between CH-A & CH-B.
2. Toggle on 2D/3D keypad will circulate between Side By Side 3D mode and 2D (or auto 3D) mode.
3. OSD Lock / Unlock: When continuously press [MENU] key in Front Panel or IR Remote Controller for 12
seconds, the OSD function will be locked to prevent from the changes of the settings by other people. To
press MENU key for 12 seconds again, it will unlock OSD and user can manipulate the OSD again.
4. Picture menu in the OSD can only be activated while the input signal is not in color [Preset Mode]. To select
[Image Properties] [Custom] [Save], then user can activate [Picture] menu again.
5. [Image Setup] menu will not be activated if the input source is not from VGA.
6. Procedures to do system Reset: OSD Menu [Options][Reset][Reset All]
7. To set [Menu Time Out] to “0”, the OSD will appear till the OSD Menu has been turned off.
8. To set [Logo Time Out] to “0”, the splash screen will not show splash screen Logo while AF5D is powered on.
9. Shortcut Hot Keys on the front panel are only functional while the OSD menu is not activated. Once the OSD
menu is activated, these keys will be served as OSD functional keys.
10. The audio from PC audio input Jack on the front panel will be mixed with video and output to RH/LH DVI-D
output ports through HDMI connection.
11. The embedded audio from HDMI input signal can be decoded and output to PC audio output Jack on the
front panel.
Minimum Equipment required for 3D display
1. 1x G-201
2. 2x Projectors (Native resolution above XGA
with DVI/HDMI input connector)
3. 2x polarizers (For RH & LH eyes)
4. 1x 3D screen (Silver matte)
5. 3D glasses (Paired with polarizer)
6. 3x DVI-HDMI cables or HDMI cables with 3x
DVI to HDMI adapters
7. Video source with 3D content
G-201 Quick User Manual Document: G-201101
------------------------------------------------------------------------------------------------------------------------------------------------
3
Installation process for 3D display
1. DVI to HDMI adapters or DVI to HDMI cables are required if the connection with video source or projectors
is not through DVI port.
2. Connect GeoBox with signal source, RH output to RH eye projector and LH output to LH eye projector.
3. Reset GeoBox to factory default settings via OSD [Option] menu to ensure no unexpected settings.
4. Install polarizer into RH & LH projectors before two projector image alignment. Make sure RH/LH
polarizers are set in correct projector, direction and angle with distance of 5-15cm to the lens to avoid
thermal damage.
5. Blue Ray player should be set at AUTO 3D (or 1080p@24Hz) for 1080p frame packing 3D display.
6. Turn on all devices. Some projector will search input source several times due to input timing change and
HDCP validation. GeoBox will automatically connect to input source. Then the screen will show up with
double images. If no input source is detected, GeoBox will go into power saving mode. The screen will
show [Power Saving Mode] message.
7. Select correct input source and set output resolution to match projector native resolution.
8. Make sure two projectors are in good focus and have the same settings.
9. Align two projector images overlapped together through projector keystone correction or lens shift.
10. Activate GeoBox [3D Properties] OSD to get correct input format and 3D settings.
11. Press [L/R ID] key on remote controller or front panel to confirm the right setting in RH/LH channels.
12. Test the final result and 3D performance.
Procedures for 3D display setting in GeoBox
1. After image position alignment, to activate [3D
Properties] in OSD to select 3D formats.
2. Select [Automatic] if the 3D signal is standard 3D
formats from Blue Ray player.
3. Select [Side By Side] or [Top-Bottom] based on
user’s 3D input sources.
4. Default setting is [Automatic]
1. Activate [Identify] menu to show “R & L”
characters on the screen at the same
time to verify the final 3D settings.
2. RH eye should see only “R” and LH eye
should see only “L”.
If the projector can accept 1080P@24Hz timing, please enable [1080P 24Hz output] to get better video
image, otherwise G-201 will output 1080P 60Hz signal.
Loading...