VMS Touring X Series, Touring Installation Manual

Touring X Series

General Installation Guide

Contents

General Installation guide

General Wiring Diagram

Page 1&2

Page 3

WIRING DIAGRAM

RED

RED

AMP-C

BLUE

AUDIO FRONT L OUT

AUDIO FRONT R OUT

AUDIO REAR L OUT

AUDIO REAR R OUT

AUDIO SUB OUT

EXTERNAL AMPLIFIER

WHITE

WHITE

GREEN

F

G

H

A N/A

C

D

E

REAR MONITOR
VIDEO OUTPUT

REAR MONITOR
AUDIO OUTPUTS

YELLOW

WHITE

RED
REAR SEAT
MONITOR
AND AUDIO

LIGHT SWITCH

BATTERY

+BATTERY

GND

ACC

ILLUM

REAR R

FRONT R

FRONT L

REAR L

ACC

YELLOW

FUSE 15A

RED

ORANGE

PURPLUE/BLACK (-)

PURPLUE (+)

GREY/BLACK (-)

GREY (+)

WHITE/BLACK (-)

WHITE (+)

GREEN/BLACK (-)

GREEN (+)

GND

BRAKE

STOP / BRAKE SWITCH

BLACK

GREEN/WHITE

E

USB

iPOD

RADIO ANTENNA

REVERSE

CAMERA

REVERSE CAMERA IN

MICROPHONE

ANTENNA CONTROL

BROWN

+12v Reverse
Camera Trigger

A

iPOD

GENERAL INSTALLTION GUIDE

• Install the microphone and
microphone wire where it cannot
interfere while driving.

• Do not install microphone where it
can interfere with switches in the
vehicle.

• If installing into a vehicle equipped
with airbags, ensure all parts of the
microphone do not interfere with
airbag operation.

1 x Main Unit
1 x Power Loom (power, speakers, camera in)
1 x AV in/out loom
1 x USB Cable
1 x USB Adaptor
1 x iPOD Cable
1 x GPS Antenna

1 x Bluetooth Microphone

1
2
3
4
5
6
7
8

Be sure to read this installation guide thoroughly prior to installation. If installation methods or non standard parts not specified in this installation manual
are used, accidents or injury may result. Professional installation is required for this system. VMS recommends installation to be completed by an
authorised VMS dealer. The customer should keep this manual after installation for future reference.

Remove Factory Radio

What’s In The Box

IMPORTANT!!!

Mounting Bracket to Main Unit

Park Brake Connection (example)

Connect BRAKE wire

If fitting a reverse camera, connect the REVERSE CONT wire (BROWN)

Reverse Lamp

Connect REVERSE CONT wire

Connect the BRAKE wire (GREEN / WHITE) on the power loom to the park
brake signal wire of the vehicle.

Reverse Wire connection (example)

Before Starting?

GPS antenna

Bluetooth Microphone

Radio Fascia Panel

Factory radio mounting brackets

VMS Unit

Factory radio mounting bracket

To maintain proper function the unit
body must be mounted at less than
30 degrees from horizontal. If the
angle is excessive, CD/DVD skipping
and improper ejection may be
experienced.

30 Degrees

Hexagonal Screws
M5 x 8

Factory Radio

Disconnect the GND from the main
vehicle battery.

Ensure the antenna has a clear view of the sky. Attach Antenna to dash
surface with double sided adhesive pad provided.

- Select a location that is at least 30 cms from the body of the unit,
otherwise the accuracy of the GPS will decrease.

- If installing the GPS antenna inside the vehicle, the installation location
& shape of the vehicle’s cabin can decrease the sensitivity and accuracy
of the GPS signal. Accuracy is generally lower and GPS lock times are
generally longer when the antenna is placed in the cabin.

Ensure the microphone is mounted securely.

Microphone

A pillar

GPS antenna

PLEASE NOTE: Some vehicles may require repositioning of the
factory mounting holes in order to align the unit properly with the
dash. In these cases, re-drill the mounting positions on the bracket.

CONNECTIVITY

WARNING!!!

Refit radio fascia panel.

Install unit Into Dash

Connect Ground Terminal on Battery

Functionality Test

QUALITY ASSURANCE CHECKLIST

Connect all wiring on the back of the head unit including:

• Power & Speaker Loom

• AV Loom

• GPS Antenna

• iPOD Cable

• USB Cable

• Radio Antenna

• This system is designed for 12-volt DC operation,
negative grounded Vehicles only. Never install into a
24-Volt vehicle such as commercial trucks or diesel
vehicles with cold region specifications. If unsure,
contact the manufacturer of the vehicle.

• Do not place any plastic storage bags over a person’s
head. This may cause suffocation or death.

• Keep small parts such as screws and brackets out of
reach of children.

• Do not disassemble, rebuild or alter the product.
Sophisticated electronic components internally may
cause injury, fire or electric shock.

• When it is necessary to replace the fuse, always use
a fuse of the correct ra

tings (no. of amperes) Inappropri-

ate fuses may cause a fire.

• Do not operate the product after experiencing a
problem. Doing so will cause further damage to the
product and may lead to fire, or electric shock.

If an abnormal situation occurs, such as foreign matter
entering the product or it comes into contact with liquids,
smoke or strange odors are emitted, power off the
product immediately and consult the dealer where the
product was purchased. Continued operation may
cause injury, fire or electrical shock.

To ensure the installation is successful and all functions of the system are
operational, drive the vehicle into an open area with a clear view of the sky
and turn the ignition to the on position.

Complete the following quality assurance checklist.

Ensure connections at the rear of unit are secure with no pressure applied on
any connections. Excessi

ve pressure may result in damaging the connection

lead or breaking the connection from the unit itself.

Powers on and off with ignition.

Scan and store both FM and AM radio stations.

Insert and eject CD/DVD.

iPOD connectivity.

iPOD functionality.

USB connectivity (to USB flash disk).

Reverse Camera is operational.

Bluetooth is operational.

System audio volume is operational.

BASS/TREBLE, FADE/BAL is operational.

Navigation is operational with GPS lock.

Do not press front fascia buttons with force, they may dislodge

.

Radio Fascia Panel

Factory Radio

Factory radio mounting brackets

Re-connect the GND terminal on the main vehicle battery.

Remove transit screws from DVD
mechnism.

• Bluetoothe Microphone