Page 1
Instruction Sheet For:
PM-LP & PM-LPB
For more information, please contact us at:
345 Log Canoe Circle, Stevensville, Maryland 21666
Toll Free: 877.281.2169 Phone: 410.643.6390 Fax: 410.643.6615
www.videomount.com
Page 2
.
QTY
1
4
4
2
1
1
1
1
1
1
4
4
4
16
16
4
1
1
2
1
1
4
4
4
4
4
4
Ceiling Plate
DESCRIPTION
Nylon Nut M6*P1.0
Feed Through Coupler
Socket Screw M6*P1.0*L20
1
2
3
NO.
ITEM
4
Outer Mast
5
6
Lower Plate
Upper Plate
7
8
9
Mid Plate
Inner Mast
12*T1.6
Leg
Foot
Bottom Plate
10
11
12
6.4*
Longer Foot
Washer
Socket Screw M6*P1.0*L12
13
14
15
M3 Allen Key
18UNC*L2 1/2"
Hex Head Screw 5/16" -
Wing Screw M6*P1.0*L10
16
Nylon Nut 5/16" - 18UNC
17
18
M4 Allen Key
Cross Screw M4*P0.7*L12
Brake Screw 1/4" - 20UNC*L3/8"
19
20
21
22
Plastic Bushings
Cross Screw M5*P0.8*L12
Cross Screw M6*P1.0*L12
23
24
25
19*T1.6
8.3*
Lag Screw 5/16"*L2.5"
Washer
26
27
1
15
2
PM-LP
16
4
14
813
11
9
10
25
12
27
3
17
26
5
19
6
18
22
23
7
24
6
20
Page 3
Step 2: Attaching the feet to
the projector
Step 1
Before starting, lay out all parts to your mount and match them to the
parts list provided. Verify that you have all your parts before attempting to assemble the mount.
Step 2
Attach the feet or to the projector using the appropriate
screws or .
22
12
23
13
Step 3
Attach the feet or to the legs using the wing screws
16
Note: If you plan to feed the cables through the holes in the cen-
12
13
11
ter of the mount itself take the time to do so now before proceeding
further. Note: If using the longer feet use the M6 screws in
the rear holes of the feet in addition to the wing screws to better
13 24
16
secure the longer foot.
If you are using the fl ush mount plate:
Step 3: Attaching the feet to
the mount
Step 4: Attaching the mount
to the ceiling plate
Step 4
Attach the ceiling plate to the top of the upper plate using
the short socket head screws and washers .
1
14
15
7
Step 5
Mark the ceiling or desired mounting surface in preparation of installation of ceiling plate . If mounting to wooden ceiling joists, pre drill
pilot holes using a 7/32” drill bit. Attach the ceiling plate to the
wooden ceiling joist using the 5/16” by 2.5” long lag screw and
washer . Proceed to step 10. WARNING: Please verify that your
27
1
1
26
mounting surface will support the combined weight of your mount,
mounting hardware, and fl at panel. Also verify that the mounting
surface is safe to drill through. Please note only mounting hardware
for mounting to wooden ceiling joists will be provided with the unit.
If mounting to a surface other than wooden ceiling joists then other
hardware will be required. If in doubt or uncertain about any of the
above, please contact a professional installer.
If you are using the ceiling plate:
Step 5: Attaching the
ceiling plate to the ceiling
Step 6
Attach the feed through coupler to the ceiling plate using
the longer socket screws , washers and nylon nuts .
2
4
15
1
3
Step 6: Attaching the feed
through couple to the ceiling
plate
Page 4
Step 7: Attaching the ceiling
plate to the ceiling
Step 8: Attaching the feed
through couple to the mount
Step 7
Mark the ceiling or desired mounting surface in preparation of installation of ceiling plate . If mounting to wooden ceiling joists,
1
pre drill pilot holes using a 7/32” drill bit. Attach the ceiling plate
1
to the wooden ceiling joist using the 5/16” by 2.5” long lag
screw and washer . WARNING: Please verify that your
26
27
mounting surface will support the combined weight of your mount,
mounting hardware, and fl at panel. Also verify that the mounting
surface is safe to drill through. Please note only mounting hardware
for mounting to wooden ceiling joists will be provided with the unit.
If mounting to a surface other than wooden ceiling joists then other
hardware will be required. If in doubt or uncertain about any of the
above, please contact a professional installer.
Step 8
Attach the other feed through coupler to the top of the upper
plate using the shorter socket screws and washers .
7
4
14
15
Step 9
Screw the extension outer tube into the feed through couple
on the ceiling plate . Screw the extension inner tube
4
into the feed through couple on the upper plate . Tighten
6
brake screws into the threaded holes in the feed through
couples to secure the extension tubes in place. To adjust the
4
19
drop length of the mast, remove the 5/16” screw and slide the
5
1
7
17
inner tube so one of the other holes in the inner tube line up with
the holes in the outer tube. Then reinsert the 5/16” screw and
retighten the nylon nut .
18
17
Step 9: Connecting the mount
to the ceiling plate
Step 10: Post installation
adjustment
Step 10
To adjust the tilt or pan of the projector, simply drag the projector to the desired position. If you have diffi culty doing so, slightly
loosen the short socket screws that are in the plastic bushing
until desired tension is achieved to make tilting or panning eas-
25
14
ier. Cables may be ran through the center of the mount and the
ceiling mast either by using the holes in the feed though couplers
or the holes in the center of the mount and ceiling plate. Please
verify that all nuts and screws are securely tightened.
Enjoy Your Mount!
WARNING: The installer of these products must verify that
the mounting surface, ceiling or wall, will safely support the
combined weight of all attached equipment and hardware.
Video Mount Products will not be held liable for the improper
use or installation of its products.
Loading...