Page 1
Instruction Sheet For:
PDS-LWA & PDS-LWAB
For more information, please contact us at:
345 Log Canoe Circle, Stevensville, Maryland 21666
Toll Free: 877.281.2169 Phone: 410.643.6390 Fax: 410.643.6615
www.videomount.com
Page 2
2
1
4
4
4
4+16
4
4
4
4
4
4
4
4
4
4
4
18*T2.0
8
4
1
1
NO. Part Name QTY.
NO. Part Name QTY.
10.2* 19*T1.6 8
8.2* 19*T0.6(Cu) 4
Cross Screw M8*40MM
ALLEN SCREW M10*P1.5*L50MM
Nylon Nut 3/8''-16UNC
Allen Key M6
1 Wall Plate 1
2 Wall Mounting Bracket 1
3 Wall Bracket Base 4
4 Wall Arm 2
5 Screen Arm 2
6 Pivot Mount Bracket 2
7 Pivot Mount 2
8 Pivot Bolt 2
9 Pivot Mount Plate 2
10 Screen Mount Bracket 2
11 Mounting Tube 2
12 Cross Screw 1/4''-20UNC*1'' 4
13 ALLEN SCREW M8*P1.25*L15MM 6
14 Washer
16 BRAKE SCREW M12*P1.75*L12MM 4
17 Shaft 4
15 Washer
21
20
18
Cross Screw M6*12MM
Cross Screw M8*16.5MM
Cross Screw M5*12MM
Cross Screw M4*12MM
31432
30
Cross Screw M5*30MM
Cross Screw M4*30MM
33
34
35
Lock Washer M4
Cross Screw M6*35MM
36
37
38
Lock Washer M5
39
5.5*
Lock Washer M6
Lock Washer M8
Spacer M6
41
40
44
43 Washer
ADJUSTABLE SCREW M6*P1.0*10
Allen Key M8
Spacer M8
54
51
45
Allen Key M5
ALLEN SCREW M8*P1.25*L20MM
55
56
10
13* 24*1.6 4
8.5* 25*2.0 4
6.2* 32*T1.6 2
12.7*50.5 2
8.3x 19xT1.6 6
9
11
57 Hex Nut M16*P2.0 2
58 Washer 20*89 4
60 Carriage Screw M8*P1.25*80 4
61 Nylon Nut M8*P1.25 2
62 Washer
63 Washer
64 Handle 2
66 Spacer
67 Washer
68 Cross Screw M6*P1.0*16 2
69 Rear Cover Base 4
70 Rear Cover 4
71 Front Cover Base 4
72 Front Cover 4
73 Hex Wood Screw 5/16''x2.5'' 6
74 Washer
21
51
8
66
57
54
1
PDS-LWA
15
20
16 17
14
56
55
58
60
63
67
68
7
6
62
61
64
13
5
72
71
74
73
45
44
70
69
4
32
18
12
3
2
30 31 32 33 34 35
36 37 38 39 40 41 43
Page 3
Step 2 : Attaching the wall plate
(Lag screws are not included)
Step 1
Before starting, lay out all parts to your mount and match them to
the parts list provided. Verify that you have all your parts before
attempting to assemble the mount.
Step 2
Mark the wall or desired mounting surface in preparation of installation of wall plate . If mounting to wooden studs, pre drill pilot
holes using a 7/32” drill bit. Attach the wall plate to the wooden stud using the 5/16” by 2.5” long lag screw and washer
74
making sure the small ear f aps are on the top rail of the wall
plate . WARNING: Please verify that your mounting surface
1
1
1
73
will support the combined weight of your mount, mounting hardware, and fl at panel. Also verify that the mounting surface is safe
to drill through. Please note only mounting hardware for mounting to wooden studs will be provided with the unit. If mounting to
a surface other than wooden studs then other hardware will be
required. If in doubt or uncertain about any of the above, please
contact a professional installer.
Step 3A: Attaching the fl at
panel to the mount (holes are
not recessed)
Step 3
Determine the correct screw size and if you need to use washers,
lock washers, or spacers. Note: Spacers are used for TVs with re-
cessed hole patterns. Secure the TV to the screen mounting brack-
10
ets using the appropriate hardware through . In
30
order to line up the holes on the screen mounting bracket you
may need to loosen the adjustable screws make sure to re-
51
45
10
tighten them after if you do. Note: For smaller hole patterns it may
be necessary to place one of the screen mounting brackets in
between the pivot mount brackets . To do so simply remove
the washer and screw from the end of the mounting tube
. Slide off the screen mounting bracket and the pivot
11
mount bracket and slide them back on in the reverse order.
Replace the washer and screw onto the mounting tube
11
when fi nished.
67
9
67
68
9
10
68
10
Step 3B: Attaching the fl at
panel to the mount (holes
are recessed)
Page 4
Step 4 : Attaching the wall
mounting bracket to the
wall plate
Step 4
Lift the monitor with the arms attached so the bent lip on the
wall mounting bracket catches the top edge of the wall
plate . Note: This should be done with at least two people in
1
2
order to prevent possible injury. Once the wall mounting brack-
et is on the wall plate then use the ¼” – 20UNC screws
2
to secure the wall mounting bracket in place.
12
1
Step 5
To run the cables along the articulating arms pop off the cable
covers & along the top and bottom of the arms and run
your cables as desired. Reattach the cable covers & to
their respective bases & when f nished.
7270
72
70
69
71
Step 6
In order to tilt the mount, loosen the tilt adjustment handles
64
slightly tilt the monitor and retighten the handles.
Please verify that all nuts and screws are securely tightened.
Step 5 : Running the cables
along the arms
Enjoy Your Mount!
WARNING: The installer of these products must verify that the mount surface, ceiling or wall, will safely
support the combined weight of all attached equipment and hardware. Video Mount Products will not
be held liable for the improper use or installation of its products.
Loading...