VMP LCD-DM2 User Manual

VIDEO MOUNT PRODUCTS

For more information, please contact us at:

345 Log Canoe Circle, Stevensville, Maryland 21666

Toll Free: 877.281.2169 Phone: [phone] Fax: [phone]

www.videomount.com

Instruction Sheet For:

LCD-DM2

I 2

2

2

4

4

B

A

LCD-DM2

CONNECTOR
"U"

CONNECTOR

CONNECTOR
2A

2B

I 1

-----

--

¢Jl0.5*¢J86*T3.0

MfO*Pl.5*L50

010.2*¢J80*T2.0

TUBE

WASHER

SCREW
LLEN

WASHER

OUTER

IMETAL

4

3 1

5

M6*Pf.O*Lf2

M6

M5*Pf.0*L8

SCREW

KEY

toSS

SCREW

LLEN

10

PLUG
ND

12

PRODucr5

MOUNT

VIDEO

4

~

~

\;l

l)

l'i

Il)

®---]

Step 2: Through bolting the mount

Step1

Before starting, lay out all parts to your mount and match them to the
parts list provided. Verify that you have all your parts before attempt­ing to assemble the mount. Note: The LCD-DM2 and LCD-1 combo was

designed to mount two of the same TV or TVs of similar size and weight.

It is not designed to have two signif cantly different TVs mounted. Also

note that LCD-1 part numbers have hexagons around their numbers

and LCD-DM2 has circles around its part numbers.

Through bolting the LCD-DM2

Step 2

Mark the desk or desired mounting surface in preparation of instal­lation of the bottom tube LCD-DM2. Drill a ½” hole through the
desired mounting surface. Place a plastic washer LCD-DM2 on
either side of the drilled hole and place metal washers LCD-DM2
on top of the plastic washers LCD-DM2. Insert the M10 screw
LCD-DM2 through the bottom most metal washer LCD-DM2

6 5

through to the top most metal washer and then screw the bottom
tube LCD-DM2 onto the M10 screw. Warning: Please verify

that your mounting surface will support the combined weight of

your mount, mounting hardware, and monitor. Also verify that the

mounting surface is safe to drill through. If in doubt, please contact

a professional installer.

3

3

4

5

4

Step 3: Connecting the base seat

Step 4: Clamping down on the desk

Step 3

Make sure the fl at head screw LCD-DM2 is connecting the bottom
tube LCD-DM2 to the base seat LCD-DM2. Note: The mount
may come assembled with the button cap M10 screw LCD-DM2
attaching the base seat please make sure to attach the fl at head
screw instead.

3

17

21

6

Step 4

Place the clamp on the edge of the desk or mounting surface and
turn the adjustable bolt LCD-DM2 until the fi xed plate LCD-
DM2 is tight against the bottom of the desk or desired mounting
surface. Warning: Please verify that your mounting surface will sup-

port the combined weight of your mount, mounting hardware, and

monitor. If in doubt, please contact a professional installer.

19

18

Key:

LCD-1

LCD-DM2

VIDEO MOUNT PRODUCTS

Step 5

Now is time to adjust height of the upper tube LCD-DM2 and
connectors A and B and LCD-DM2 to the desired height of

2A

2B

your TV. To adjust the height of the upper tube LCD-DM2 simply
remove the M8 screw LCD-DM2 and nylon nut LCD-DM2.
Next slide the upper tube LCD-DM2 along the bottom tube
LCD-DM2 matching up the height adjustment holes on the

3

13

two of them until you get your desired height. Then secure the up­per tube LCD-DM2 again using the M8 screw LCD-DM2
and nylon nut LCD-DM2. To adjust the connectors and

2B

LCD-DM2 loosen the M6 screws LCD-DM2 and slide the

15

9

connectors to the desired height along the upper tube LCD­DM2. Retighten the screws LCD-DM2 once the connectors
and LCD-DM2 are in the proper position.

2A

2B

9

13

13

1514

1413

2A

13

Step 5: Adjusting height

Step 6: Attaching LCD-1s

Step 6

For this step it is assumed that you have assembled the LCD-1 to
the confi guration desired, but have not attached the monitors to
the mounting plates. If this is not the case, please take the time to
assemble the LCD-1. Insert the plastic fl anges LCD-1 into the
desired arm or LCD-1. Now use the 3/8” bolt LCD-1

2

and nylon nut LCD-1 to connect the arm or LCD-1
to the “U” connector LCD-DM2.

8

11

1

18

2

17

8

Step 7

Attach the monitors to the mounting plate or LCD-1 using

19 20

M4 LCD-1 or M5 LCD-1 screws. Please verify that all nuts

and screws are tight.

5A 5B

Step 7 : Attaching monitors

Enjoy Your Mount!

WARNING: The installer of these products must verify that the mount-

ing surface, ceiling or wall, will safely support the combined weight

of all attached equipment and hardware. Video Mount roducts will

not be held liable for the improper use or installation of its products.