Page 1
Instruction Sheet For:
LCD-2537 & LCD-2537B
For more information, please contact us at:
345 Log Canoe Circle, Stevensville, Maryland 21666
Toll Free: 877.281.2169 Phone: 410.643.6390 Fax: 410.643.6615
www.videomount.com
Page 2
1
20
89
1819
2
6 17
LCD-2537
25 2724 163
26
23
22
1421
12 15
11
10
5B
13
4
5A
1
1
Qty
DESCRIPTION
NO.
ITEM
1
Wall Plate
Rear Force Arm
Forward Force Arm
1
2
3
1
1
1
1
8
1
4
1
3
Stub Arm
Cable Clip
Pivot Bracket
4
Plastic Cover
Small Mounting Plate
Large Mounting Plate
6
5B
5A
End Plug 40*20
Nylon Nut 3/8"*16UNC
Adjustable Screw 1/4"-20UNC
7
8
9
10
11
1
1
1
4
1
19*T1.6
10.2*
Metal Pin
Nylon Nut M6*P1.0
Hex Screw M6*P1.0*L35
12
Washer
Hex Screw 3/8"-16UNC*L2.5"
13
14
15
16
1
1
1
1
4
20*T2.0
9.8*L72
9.8*L38.5
13*
13.5*
13*
Screw M4*P0.7*L12
Spacer
Spacer
Washer
Hex Screw 3/8"-16UNC*L90mm
18
19
20
21
17
3
4
4
4
3
Screw M5*P0.8*L12
Screw M6*P1.0*L12
Lag Screw 5/16"*L2.5"
22
23
24
4
19*T1.6
12*T1.0
8.3*
4.3*
Screw M8*P1.25*L16
Washer
Washer
26
27
25
Page 3
Step 2: Attaching the mount-
ing plate to the pivot bracket
(Mounting Plate A (#5A) shown)
Step 1
Before starting, lay out all parts to your mount and match them to
the parts list provided. Verify that you have all your parts before
attempting to assemble the mount.
Step 2
Determine which VESA standard plate you will be using or
(75mm/100mm for or 200mm/100mmx200mm for
5B
and attach the selected mounting plate or to the swivel
bracket using the M6 screw and the nylon nut .
4
5A
12
5A
5B
5A
5B
13
)
(Set this assembly safely to the side for now.)
Step 3
Mark the wall or desired mounting surface in preparation of installation of wall mounting plate . If mounting to wooden studs,
1
pre drill pilot holes using a 7/32” drill bit. Attach the wall plate
to the wooden stud using the 5/16” by 2.5” long lag screw
1
23
and washer making sure the small rotation stoppers on the
24
wall plate are towards the bottom. WARNING: Please verify that
your mounting surface will support the combined weight of your
mount, mounting hardware, and fl at panel. Also verify that the
mounting surface is safe to drill through. Please note only mounting
hardware for mounting to wooden studs will be provided with the
unit. If mounting to a surface other than wooden studs then other
hardware will be required. If in doubt or uncertain about any of the
above, please contact a professional installer.
Step 3: Attaching the wall plate
to the mounting surface
Step 4
Determine which arm confi guration you desire (double arm, single
arm, or near fl ush) and locate the correct arms. ( for near
fl ush, for single arm, and and for double arm.) Attach
the desired wall arm or to the wall plate using the 3/8”
screw , and nylon nut . Snap the plastic cover onto the
wall plate .
2
2
17
1
11
2
8
3
8
1
6
Step 4: Attaching the rear
force arm to the wall plate
Page 4
Step 5: Attaching the front
force arm to the rear force arm
Step 5
If your application calls for the double arm confi guration, at-
20
2
15
2
tach the front force arm to the rear force arm using
the metal pin , the long spacer , washers on the
16
top and bottom and between the two arms), and the nylon nut . If your application calls for the single arm or near
11
3
19
18
fl ush mount confi guration insert the short spacer into or
and continue to the next step.
8
Step 6
Attach the swivel bracket assembly from step 2 to the appropri-
2
ate force arm , , or depending on your application
using a 3/8” screw , washers , and nylon nut . Insert
adjustable screw into the back of the swivel bracket for
3
14
10
8
15
11
4
use when tilting the monitor.
Step 7
Attach the mounting plate assembly from step 2 to your fl at
panel using the M4
21
(#21), M5 (#22), M6 (#23) or M8 (#26) screws
22 23
26
as appropriate. NOTE: If you are using M4 screws with the Large
Mounting Plate
27
(#27) provided with the M4 screws (#21).
5B
(#5B) then you have to use the small washers
21
Step 6: Attaching the pivot
bracket to the front force arm
Step 8
Insert end plugs into the force arms. For cable management, insert the cable clips by pushing the arrow ends into
9
7
the square holes in the force arms.
Please verify that all nuts and screws are securely tightened.
Enjoy Your Mount!
Step 7: Attaching the fl at panel
to the mounting plate (M4
Screws (#21) shown)
WARNING: The installer of these products must verify that
the mounting surface, ceiling or wall, will safely support the
combined weight of all attached equipment and hardware.
Video Mount Products will not be held liable for the improper
use or installation of its products.
Loading...