VMP LCD-1 User Manual

Instruction Sheet For:

LCD-1 & LCD-1B

For use with at panels 10” to 23” diagonally and

weighing no more than 25 lbs.

CAUTION: This mount is intended for use only with the maximum weights

indicated. Use with products heavier than the maximum

weights indicated may result in instability causing possible injury.

For more information, please contact us at:

345 Log Canoe Circle, Stevensville, Maryland 21666

Toll Free: 877.281.2169 Phone: [phone] Fax: [phone]

www.videomount.com

2

1

21

22

17

18

19

20

LCD-1

16

15

14

7

6

9

8

111013

4 3

5

1

1

1

QTY.

Wall Plate

DESCRIPTION

NO.

ITEM

Rear Force Arm

Front Force Arm

2

3

1

4

1

1

1

Swivel Bracket

4

8

1

End Cap

Cable Clip

Plastic Cover

Mounting Plate

5

Shorter Force Arm

Adjustable Screw 1/4" -

9

7

8

6

12

3

1

1

1

20UNC*L50mm

Nylon Nut 3/8"-16UNC

11

10

1

Nylon Nut M6*P1.0

Screw M6*P1.0*L35

Screw 3/8"-16UNC*L2"

12

13

14

1

5

19*T1.6mm

Washer

Metal Pin

3/8"*

15

16

2

4

1

Screw 3/8"-

16UNC*L96mm

17

4

2

5/16"*L2.5"

Plastic Flanges

Screw M4*P0.7*L12

Screw M5*P0.8*L12

Lag Screw

19

20

18

21

2

2

19*T1.6

8.3*

Concrete Wall Anchor

Washer

23

22

Step 2: Attaching the monitor

to the mounting plate

Step 3: Attaching the wall
plate to the wooden stud

Step 4: Setting the concrete anchor

into bare concrete wall

Step 1

Before starting, lay out all parts to your mount and match them to
the parts list provided. Verify that you have all your parts before
attempting to assemble the mount.

Step 2

Attach the mounting plate to your LCD monitor using the M4

19

or M5 screws or as appropriate.

20

5

Step 3

For Wood Stud Installation:

Mark the wall or desired mounting surface in preparation of installa­tion of wall mounting plate (1). Pre drill pilot holes using a 7/32” drill
bit to a depth of 2.5”. Attach the wall plate (1) to the wooden stud
using the 5/16” by 2.5” long lag screw (21) and washer (22) making

1

1

21

22

sure the small rotation stoppers on the wall plate are towards the
bottom. WARNING: It is important that the mount is attached in

the center and NOT the edges of the stud for safe support. Please
verify that your mounting surface will support the combined weight

of your mount, mounting hardware, and at panel. Also verify that

the mounting surface is safe to drill through. If in doubt or uncertain
about any of the above, please contact a professional installer.
Improper installation invalidates the UL listing of the product.

Step 4

For Concrete Installation:

Mark the wall or desired mounting surface in preparation of instal­lation of wall mounting plate (1). Pre drill pilot holes using a 3/8” or

1

M10 drill bit to a depth of 2.5”. Clean out the pre drilled hole with
a vacuum or compressed air. Insert the concrete anchor (23) into

23

the pre drilled hole and tap the anchor ush with the surface of
the concrete with a hammer. NOTE: If drywall is on the surface of

the concrete the anchor must be countersunk so it is ush with the

surface of the concrete below. Also note the dry wall thickness
should not exceed 5/8”. Concrete covered by drywall mounting
condition has not been evaluated by UL. Attach the wall plate

(1) to the concrete wall by screwing the 5/16” by 2.5” long lag

1

screw (21) and washer (22) into the concrete anchor (23) making

21

22 23

sure the small rotation stoppers on the wall plate are towards the
bottom. WARNING: Please verify that your mounting surface will

support the combined weight of your mount, mounting hardware,

and at panel. Also verify that the mounting surface is safe to drill

through. If in doubt or uncertain about any of the above, please
contact a professional installer. Improper installation invalidates
the UL listing of the product.

Step 4: Setting the concrete anchor

into drywall covered concrete wall

(not evaluated by UL)

Step 5: Attaching the wall

plate to the concrete wall

Step 5

Next determine which arm conguration you desire (double
arm, single arm, or near ush) and locate the correct arms ((8)
for near ush, (2) for single arm, OR (2) and (3) for double arm).
Attach the desired wall arm (2) or (8) or to the wall plate (1) us-
ing the 3/8” screw (17), plastic anges (18) and nylon nut (11).
Snap the plastic cover (6) onto the wall plate (1).

2

2

17

6

2

8

3

18

1

8

1

11

Step 6

If your application calls for the single arm or near ush mount
conguration proceed to the next step. If your application
calls for the double arm conguration, attach the front force

arm to the rear force arm using the metal pin , wash­ers and the nylon nut .

3

15

2

11

16

Step 7

Attach the swivel bracket to the appropriate force arm
( , , or depending on your application) using a 3/8”
screw , washers , and nylon nut . Insert adjustable
screw into the back of the swivel bracket for use when

3

2

10

8

1514

4

11

4

tilting the monitor.

Step 6: Attaching the front

force arm to the rear force arm

Step 7: Attaching the pivot

bracket to the front force arm

Step 8

Attach the mounting plate to the swivel bracket using the
M6 screw and nylon nut .

12

5

13

4

Step 9

Insert end plugs into the force arms used by your application.
Insert the cable clips by pushing the arrow ends into the square
holes in the force arms.

Please verify that all nuts and screws are securely tightened.

Step 8: Attaching the mounting

plate to the pivot bracket

Enjoy Your Mount!

WARNING: The installer of these products must verify that
the mounting surface, ceiling or wall, will safely support the
combined weight of all attached equipment and hardware.
Video Mount Products will not be held liable for the improper
use or installation of its products.