Page 1
VIDEO MOUNT PRODUCTS
Instruction Sheet For:
IWB-1
For more information, please contact us at:
325 Log Canoe Circle, Stevensville, Maryland 21666
(T) 410.643.6390 / (F) 410.643.6615
www.videomount.com
Page 2
1
QTY.
1
2
4
1
4
4
1
1
1
1
Wall Box
DESCRIPTION
1
NO.
ITEM
Trim Cover
Mount Supports
Screw M8*P1.25*L12
3
4
2
20UNC*L2"
Lag Screw M8*L50
Screw M4*P0.7*L10
Large Mounting Plate
5
6
7
LCD-1 Pivot Bracket
Small Mounting Plate
8
2 1
Adjustable Screw 1/4"-
LCD-2537 Pivot Bracket
9
10
11
5
6
3
IWB-1
9
8
10
7
4
11
Page 3
WARNING: It is HIGHLY recommended the installation of the IWB-1 be installed by a
qualifi ed professional, as the installation process can be dangerous and result in per-
sonal injury or death if done improperly. If at any point you are unsure about what you
are doing, STOP and contact a qualifi ed professional.
Step 1
Before starting, lay out all parts to your mount and match them
to the parts list provided. Verify that you have all your parts
before attempting to assemble the mount. Please identify
which color your LCD-1/LCD-2537 is, silver or black, and only
use the parts #7-11 or #12-16 which are the correct color for
your mount. Set aside the other color of parts. If you wish to
paint the wall box , mount supports and trim cover to
match or wall or mounting surface please do so at this time.
Step 2
Identify a proper installation site of the IWB-1. Note: The IWB-1
is designed to go in between two wooden studs with 16” cen-
Step 3: Outline of the cutout for the IWB-1
ters. There will not be enough space remaining to the side of
the IWB-1 for electrical wires/cables, plumbing, ductwork or
insulation. Please take this into account when locating the
installation site.
1
2
4
** Step 3 **
Use a stud fi nder to locate the desired studs and mark their
locations. Center and level the housing and using the housing as a template draw around the edges of the box .
Cut out the drywall within the drawn line.
1
Step 4
If installing electrical junction boxes into the wall box please
do so at this time using the knockouts in the top or the bottom of the box. Route any audio/visual cables through the
knockouts also located on the top and bottom of the wall
box at this time as well.
1
1
Step 5
Step 5: Inserting the wall box into the wall
** WARNING: ELECTRICAL SHOCK HAZARD! CUTTING OR DRILLING INTO ELECTRICAL WIRES OR CABLES
CAN RESULT IN DEATH OR SERIOUS PERSONAL INJURY! Always make sure the area you are preparing to cut
or drill into is completely clear of electrical wires before you proceed in order to prevent injuries.
Insert the wall box into the wall.
1
** WARNING: EXPLOSION AND FIRE HAZARD! CUTTING OR DRILLING INTO GAS PLUMBING CAN RESULT IN
DEATH OR SERIOUS PERSONAL INJURY! Always make sure the area you are preparing to cut or drill into is completely clear of gas, water, waste or any other plumbing before you proceed in order to prevent injuries.
Page 4
Step 6: Lagging the wall box
into the studs
** Step 6 **
Pre-drill and attach the wall box to the studs using the M8 lag
crews provided. Note: It is very important the front of the box
1
is as fl ush as possible with the wall as to insure a proper fi t for the
trim cover .
If you are installing a LCD-1 into the IWB-1 proceed to the next step.
If you are installing a LCD-2537 into the IWB-1 proceed to step 9.
6
4
1
Step 7
2
11
14
3
11
15
15
11
16
1510
10
Attach the front force arm to the rear force arm using the
metal pin , washers and nylon nut . Attach the LCD-1 pivot
bracket provided with the IWB-1 or to the front force arm
using the 3/8” screw , washers and nylon nut . Insert the
3
adjustable screw provided with the IWB-1 or into the threaded hole of the pivot bracket IWB-1 or .
16 15
Step 7: Assembling the LCD-1 arm
Key:
IWB-1
LCD-1
VIDEO MOUNT PRODUCTS
** WARNING: ELECTRICAL SHOCK HAZARD! CUTTING OR DRILLING INTO ELECTRICAL WIRES OR CABLES
CAN RESULT IN DEATH OR SERIOUS PERSONAL INJURY! Always make sure the area you are preparing to cut
or drill into is completely clear of electrical wires before you proceed in order to prevent injuries.
** WARNING: EXPLOSION AND FIRE HAZARD! CUTTING OR DRILLING INTO GAS PLUMBING CAN RESULT IN
DEATH OR SERIOUS PERSONAL INJURY! Always make sure the area you are preparing to cut or drill into is completely clear of gas, water, waste or any other plumbing before you proceed in order to prevent injuries.
Page 5
Step 8: Attaching the mount supports
Step 9: Assembling the LCD-2537 arm
Step 8
Insert the end plugs into the rear force arm and use the long
3/8” bolt and nylon nut to attach the mount supports to
the bottom and top of the rear force arm . Proceed to step 11.
17
18
11
2
2
2
Step 9
Insert the longer spacer into the rear force arm and attach
the front force arm to the rear force arm using the metal pin
16
, 3/8” washers , ½” washer and nylon nut . Attach the
LCD-2537 pivot bracket provided with the IWB-1 or to the
front force arm using the 3/8” screw , 3/8” washers and
nylon nut . Insert the adjustable screw provided with the IWB-1
or into the threaded hole of the pivot bracket or .
11
11
16
15
3
19
3
18
2
14
2
11
9
14
15
9
14
Step 10
Use the long 3/8” bolt and nylon nut to attach the mount
supports to the bottom and top of the rear force arm .
2
17
11
2
Step 11
Determine the VESA mounting hole pattern for your LCD. If the hole
pattern is either 75 mm x 75 mm (about 3” x 3”) or 100 mm x 100 mm
(about 4” x 4”) then you will use the small mounting plate or .
If the hole pattern is either 100 mm x 200 mm (about 4” x 8”) or 200
mm x 200 mm (about 8” x 8”) then you will use the large mounting
plate or . Attach the appropriate mounting plate , ,
or using the screws provided with the LCD-1 or LCD-2537.
7
12
12
13
13
8
87
Step 10: Attaching the mount supports
Step 11: Attaching the mounting plate
Key:
IWB-1
LCD-1 or LCD-2537
VIDEO MOUNT PRODUCTS
Page 6
Step 12A: Mount support location diagram
Step 12
Determine if you want the arm to fold left or fold right. If you want
the arm to fold right you use the fi rst and second column of holes. If
you want the arm to fold left you use the second and third column
of holes. Attach the mount supports to the wall box using
the M8 screws . Note: For the LCD-2537 you should use the fi rst
and third rows of holes. For the LCD-1 you should use the second
and forth rows of holes.
6
2
1
Step 13
Attach the trim cover to the wall box using the M4 screws
provided with the IWB-1.
5
4
1
Step 14
Attach your LCD to the LCD-1 or LCD-2537 arm using the M6 screw
LCD-1 or LCD-2537 and nylon nut LCD-1 or LCD-2537 to attach the mounting plate , , or to the pivot bracket ,
10
14
, or .
15
12
7
8
1312
13
9
Step 12B: Attaching the mount
supports to the wall box
Step 13: Attaching the trim cover
Please verify that all nuts and screws are completely and securely
tightened.
Enjoy Your Mount!
WARNING: The installer of these products must verify that the mounting surface, ceiling or wall, will safely support the combined weight
of all attached equipment and hardware. Video Mount Products will
not be held liable for the improper use or installation of its products.
Step 14: Connecting the mounting
plate to the pivot bracket
Key:
IWB-1
LCD-1 or LCD-2537
VIDEO MOUNT PRODUCTS
Loading...