VMP FP-LFVB User Manual

Instruction Sheet For:

FP-LFV & FP-LFVB

For more information, please contact us at:

345 Log Canoe Circle, Stevensville, Maryland 21666

Toll Free: 877.281.2169 Phone: [phone] Fax: [phone]

www.videomount.com

1

6

3

24

23

FP-LFV

2

2

2

2

6

2

1

4

QTY.

22

10

9

4

4

4

4

4

4

5

4

4

7 8

11

12

13

4

4

4

1

6

4

4

4

4

6

21

2019

18171615

14

Wall Plate

DESCRIPTION

ITEM

Vertical Support

Cross Screw M4*P0.7*L6

Screen Mounting Bracket

1

2

3

NO.

4

Lock Washer M4

Long Allen Key M4

Cross Screw M4*P0.7*L12

Cross Screw M5*P0.8*L12

Cross Screw M6*P1.0*L12

Cross Screw M4*P0.7*L30

Cross Screw M5*P0.8*L30

Security Screw M5*P0.8*L20

5

6

7

Cross Screw M8*P1.25*L16.5

8

9

10

Cross Screw M6*P1.0*L35

11

12

13

Lock Washer M5

Cross Screw M8*P1.25*L40

14

15

16

18*T2.0

5.5*

Spacer M6

Spacer M8

Lock Washer M6

Lock Washer M8

Washer

17

18

19

Magnetic Level

Lag Screw 5/16"*2.5"

20

21

22

23

19*T1.6

8.3*

Washer

24

Step 2: Assembling the wall plate

Step 3: Mounting the wall plate

Step 1

Before starting, lay out all parts to your mount and match them to the
parts list provided. Verify that you have all your parts before attempt­ing to assemble the mount.

Step 2

Assemble the wall plate by attaching the two horizontal wall plates
using the vertical supports and short M4 screws .

1

2

4

Step 3

Mark the wall or desired mounting surface in preparation of installation
of wall plate assembly and . If mounting to wooden studs, pre

1

2

drill pilot holes using a 7/32” drill bit. Attach the wall plate assembly

1

and to the wooden stud using the 5/16” by 2.5” long lag screw
and washer .

23

2

WARNING: Please verify that your mounting sur-

24

face will support the combined weight of your mount, mounting hard­ware, and fl at panel. Also verify that the mounting surface is safe to drill
through. Please note only mounting hardware for mounting to wooden
studs will be provided with the unit. If mounting to a surface other than
wooden studs then other hardware will be required. If in doubt or uncer­tain about any of the above, please contact a professional installer.

Step 4A: Attaching the mounting

brackets to the fl at panel (spacers

not needed)

Step 4B: Attaching the mounting

brackets to the fl at panel (spac-

ers needed)

Step 4

Determine the correct screw size and if you need to use washers, lock
washers, or spacers. Note: Spacers are used for TVs with recessed hole
patterns. Secure the TV to the mounting rails using the appropriate
hardware through . Note: The brackets have to be level with

7

21

3

each other to work properly.

Step 5

Use the hooks in the mounting rails to hook on the top rail of the wall
plate assembly . Use security screws and the long allen key to

1

secure the TVs to the bottom rail and to secure its horizontal position.

3

6 5

1

Please verify that all nuts and screws are securely tightened.

Step 5: Securing the mounting

brackets

Enjoy Your Mount!

WARNING: The installer of these products must verify that the mount
surface, ceiling or wall, will safely support the combined weight of all
attached equipment and hardware. Video Mount Products will not be
held liable for the improper use or installation of its products.