VMP FP-LFB User Manual

Instruction Sheet For:

FP-LF & FP-LFB

For more information, please contact us at:

345 Log Canoe Circle, Stevensville, Maryland 21666

Toll Free: 877.281.2169 Phone: [phone] Fax: [phone]

www.videomount.com

QTY.

4

1

4

2

2

1

4

4

4

4

4

4

4

4

8

4

4

4

4

6

1

6

DESCRIPTION

ITEM

Wall Plate

1

NO.

Mounting Bracket

Security Screw M5*P0.8*L20

3

2

Long Allen Key M4

Screw M4*P0.7*L12

Screw M5*P0.8*L12

5

6

4

Screw M4*P0.7*L30

Screw M6*P1.0*L12

7

Screw M5*P0.8*L30

Screw M8*P1.25*L16.5

8

Screw M6*P1.0*L35

9

10

11

18*T2.0

5.5*

Spacer M6

Spacer M8

Lock Washer M4

Lock Washer M5

Lock Washer M6

Lock Washer M8

Screw M8*P1.25*L40

Washer

12

13

14

15

16

17

Magnetic Level

18

19

20

19*T1.6

8.3*

Lag Screw 5/16"*L2.5"

Washer

21

22

4

FP-LF

1 2

19

2221

18

1615141312

20

17

3

5

6

7

8

9

10

11

Step 2: Mounting the wall plate

Step 1

Before starting, lay out all parts to your mount and match them to
the parts list provided. Verify that you have all your parts before
attempting to assemble the mount.

Step 2

Mark the wall or desired mounting surface in preparation of instal­lation of wall mounting plate . If mounting to wooden studs, pre
drill pilot holes using a 7/32” drill bit. Attach the wall plate to
the wooden stud using the 5/16” by 2.5” long lag screw and
washer making sure the small ear fl aps are on the top rail of the
wall plate . WARNING: Please verify that your mounting surface

22

1

1

1

21

will support the combined weight of your mount, mounting hard­ware, and fl at panel. Also verify that the mounting surface is safe
to drill through. Please note only mounting hardware for mount­ing to wooden studs will be provided with the unit. If mounting to
a surface other than wooden studs then other hardware will be
required. If in doubt or uncertain about any of the above, please
contact a professional installer.

Step 3A: Attaching the mounting

brackets to the monitor

(spacers not needed)

Step 3B: Attaching the mounting
brackets to the monitor (spacers

used due to recessed hole patterns)

Step 3

Determine the correct screw size and if you need to use wash­ers, lock washers, or spacers. Note: Spacers are used for TVs with
recessed hole patterns. Secure the TV to the mounting bracket

2

using the appropriate hardware through . Note: The

5

19

brackets have to be level with each other to work properly.

Step 4

Use the hooks in the mounting bracket to hook on the top rail
of the wall plate . Use security screws and the long allen key

4

to secure the TVs to the wall plate and to secure its horizontal

1

2

3

1

position.

Please verify that all nuts and screws are securely tightened.

Step 4: Securing the mounting

brackets to the wall plate

Enjoy Your Mount!

WARNING: The installer of these products must verify that the mount
surface, ceiling or wall, will safely support the combined weight of
all attached equipment and hardware. Video Mount Products will
not be held liable for the improper use or installation of its products.