VM Audio VM-WA525-E, VM-WA65-E, VM-WA8-E User Manual
VM-WA525-E / VM-WA65-E
VM-WA8-E
ELUX SERIES
2-WAY HIGH FIDELITY
IN-WALL SPEAKER
Congratulations on your purchase of an Elux Series product
from VM Audio. You have seen that with years of acquired
taste for quality, the Elux Series has the right design and
performance to satisfy your utmost demand. With music so
clear and rich and bass so low and loud, you will be immersed
in a world of musical euphoria that anything else will seem like
white noise. By following the installation instructions carefully,
you will ensure yourself performance that will be enjoyed from
each use for years to come. Reward yourself with the ner
things in life.
Features
• 2-Way High Fidelity In-Wall Speaker
• Multi-Component Loudspeaker Design
• Ballistic Lightweight Fiber Glass Yellow Cone
• High Compliance Half-Roll Black Rubber Surround
• Low-Resistivity Multi-Layer Round Copper Voice Coil
• Multi-Roll Radial Motion Stabilizing Poly Cotton Spider
• Dense One-Piece Solid Coated Steel Speaker Frame
• Efcient Low-Loss CAD Magnetic Motor Structure
• Precision Mylar Dome Tweeter
• Spring-Loaded Bare Wire Speaker Connector
• Dedicated Built-In 2-Way Second Order Crossover Filter
• Paint-Ready Rectangle ABS Mounting Flange Bafe
• Screw-In Quick Locking Arm System
Safety Precautions
Package Contents
Please review the contents of the package and make sure
you have received all the items included with your system.
(1) 2-Way Component Loudspeaker
(1) Removable Speaker Grille
(1) Acoustic Foam Grille Insert
(1) Cutout Template
(1) User Guide
CAUTION
1. Please read these instructions carefully before attempting
to install and operate this product.
2. Keep this User Guide for future reference.
3. Save all packaging in the event this product needs to be
returned for service or replacement.
4. Ensure to setup your system in a safe and secure manner.
5. Do not expose the loudspeaker to rain, moisture, or
dripping liquids.
6. Protect the speaker wires from getting exposed.
7. Before placing and installing this loudspeaker product,
inspect all hardware, brackets, surfaces, and associated
equipment for damage. If a fault is discovered, it should be
corrected immediately.
8. Do not attempt to service this unit, refer all servicing to
qualied service personnel.
9. This loudspeaker can easily reproduce sound pressure
levels (SPL) loud enough to cause permanent ear damage
that could result in hearing loss. Take great precaution to
protect yourself from prolonged exposure to high output
sound pressure levels.
2 3
Installation
• In-wall installation should be located directly above the
listening area. In rooms larger than the bathroom or
closet, it is recommended to install additional speakers for
improved performance.
• You may install a bracket where you will be placing the
speaker prior to installing drywall. Once insulation and
drywall is installed, you may cut the speaker hole.
• Use a stud-nder to locate the nearest wood or metal
stud and keep in mind the bafe ange will protrude
outside of the mounting hole.
Painting The Wall Speakers
• It is recommended to paint your speaker before installing
into your wall, or reverse the steps of installation to
remove the speaker for easy painting. For painting the
installed speaker, please use the paint mask in place of the
grille. If painting the grille, do not paint while attached to
the speaker, and be careful to not clog the holes, which will
decrease sound quality. VM Audio recommends only light
spray painting.
Installation Getting Started
1. Choose a location in your
home to setup your new VM
Audio in-wall speakers.
2. Using the included template,
position and outline the hole
on the wall.
Power Requirements
• For non-distorted high output performance, use an
amplier with the same power rating as the loudspeaker.
Speaker Wires
• When running long lengths of speaker wires, it is
recommended that higher gauge wire (14 Ga or higher) is
always used throughout the wiring.
3. Cut the drawn hole
using a drywall saw.
4 5
Loading...