Vizualogic 2007 Wrangler, 2008 Wrangler, A-1250, A-1150 Installation Manual

%
%
Simple and Easy to Follow Installation Manual
Free Call!
Free Call!
800-745-5337
800-745-5337
www.quadratec.com
www.quadratec.com
Expert Advice
Expert Advice
®
Vizualogic®A-1250™ & A-1150™
DVD Headrest
“JK” Wrangler Installation Instructions
Note: Be sure to read this entire instruction sheet AND the Vizualogic instruction sheet before beginning your installation. This sheet
outlines the installation of a Vizualogic brand DVD Headrest Kit into a 2007 or newer Jeep Wrangler. These instructions are intended to assist with the installation process and by no means replace the Vizualogic installation manual.
Figure 1
Recline Seat
Press to Release
Tools Required:
®
•Torx
• 7mm or 9/32 nut driver (for dash fascia panel fasteners)
• Screwdriver – straight slot (to pry dash fascia panel snaps)
• Pliers (to crimp wire taps)
T30 driver (for center console fasteners)
Figure 2
Carefully Disconnect Upholstery Channels
1.
Recline
both front seat headrests. With the headrests erected, press both side releases buttons as shown.
2. We suggest that you save the removed front seat headrests. Do not discard.
Disconnect
3. This can be somewhat strenuous so proceed with care.
(Figure 2)
4. Carefully guide posts according to the manufacturer’s installation manual. Route the cables down the seat back and exit the cables next to the center console. Install the DVD Head­rests into the guide posts in the high position and remove the slack in the cable. Not too tight here. Remember that headrest need to freely adjust up and down.
5.
Remove
cure the center console to the vehicle’s floor. There are two bolts at the rear of the center console (left and right) and two towards the front (left and right). Fastener removal al­lows the console to be lifted upwards a few inches to neatly tuck away the monitor cables and other system wiring inside the console’s shell.
both front seats to allow room to remove
(Figure 1)
the upholstery channels on both seats.
insert
video monitor cables through headrest
(Figure 2A)
the four torx head fasteners (size T30) that se-
(Figure 3)
Figure 2A
Figure 3
Upholstery Channels Hook Together Between Seat Back and Pad
Carefully Route Cables
Through Headrest
Remove All 4 T30
Torx Head Bolts
J
J
Guide Posts
Page 2 www.quadratec.com
Vizualogic®A-1250™ & A-1150™ DVD Headrest
“JK” Wrangler Installation Instructions
Figure 4
Driver Side Cables
Figure 5
Hook Material
Figure 6
Passenger
Side Cables
Audio/Video
Module
For additional copies of these instructions please visit our website for a downloadable PDF Version.
6.
Route
the Driver and Passenger side monitor cables as shown. Use two cable zip ties to neatly bundle each set of DVD cables where the cables exit the seat back and meet the center console.
Route
the four monitor cables under­neath the center console and exit the four cables at the middle of the passenger side seat slider as shown.
(Figure 4)
7.
Reconnect
Adhere
8.
the upholstery channels on both front seats.
the rough “hook” side of the “hook and loop” fastener material onto the floor carpet and under the front passenger seat as shown.
9.
Adhere
the softer furry “loop” side of the “hook and
(Figure 5)
loop” fastener material onto Audio/Video Module as shown.
(Figure 6)
Loop Material
Figure 7
A/V Control Module
Route Wires Below Seat Slider Rail
Seat Slider Rail
Page 3 www.quadratec.com
10.
Attach
the FM Transmitter Antenna to the A/V Con­trol Module and route underneath the seat slider and under the center console. Extend the FM Transmitter An­tenna towards the radio and underneath the center con­sole.
11.
Connect
the monitor wires to the A/V Control Module according to the Vizualogic installation manual. Again, route all wires below the seat slider rails.
12.
Connect
the System Power Harness to the A/V Mod­ule according to the Vizualogic installation manual. Once again, route all wires below the seat slider rails. Use sev­eral zip ties to neatly bundle the wires. Attach the A/V Module underneath the front passenger seat with the hook and loop fastener material.
(Figure 7)
Vizualogic®A-1250™ & A-1150™ DVD Headrest
13. Gently
pry
off the plastic Fascia Panel that’s in front of
“JK” Wrangler Installation Instructions
the gear shifter and just below the lower bank of switches as shown. A thin straight slot screwdriver works well. Pry from the top corners only.
14.
Remove
the two center dashboard fasteners located
(Figure 8)
directly behind the Fascia Panel using a 7mm or 9/32 Nut Driver.
(Figure 9)
15. Route the System Power Harness underneath the cen­ter console and towards dash.
16.
Disconnect
the driver side Auxiliary Power Outlet
plug and pull down passenger side power outlet.
*But Do NOT Unplug.
17.
Route
the power harness (
wires
) from the control module and underneath the seat
the Red, Yellow and Black
slider; through the center console and out the opening just below the Auxiliary Power Outlets. Locate the three red wire harness taps for the next procedure. Note how wire taps are installed but do NOT attach wire taps at this time.
(Figure 10 & 11)
Figure 8
Gently Pry
Figure 9
Driver Side Aux Power Outlet
Figure 10
Fascia Panel
Passenger Side
Aux Power Outlet
Remove Bolts
Route Wires
Through Dash
For additional copies of these in­structions please visit our website for a downloadable PDF Version.
18. Begin attaching wire tap connectors to the proper wires. There are 3 wires to connect.
a. Attach a wire tap connector to the (
stripe
) wire at the passenger side auxiliary power outlet and connect the shown to the wire tap.
YELLOW
wire from the power harness as
(Figures 10 & 14)
b. Attach a wire tap connector to the (
WHITE
Outlet plug and connect the
stripe) wire at the passenger side Auxiliary Power
BLACK
harness to the wire tap as shown.
Page 4 www.quadratec.com
RED
with
GREEN
BLACK
with
wire from the power
(Figures 12 & 14)
Wire Tap
Figure 11
Crimp with Pliers
Vizualogic®A-1250™ & A-1150™ DVD Headrest
Figure 12
Yellow Harness Power Wire
Black Harness Power Wire
Figure 13
Wire Tap Blue/Pink Wire
Plug Attached to Driver Side Power Outlet
Power Outlet Plug
Lift Dash
Panel
Red Harness Power Wire
Red Harness Power Wire
“JK” Wrangler Installation Instructions
19. Disconnect the plug attached to the driver side power outlet.
a. Attach a wire tap connector to the ( wire at the Driver side Auxiliary Power Outlet plug. Connect the
RED
wire from the power harness to the wire tap as
shown.
b. Tuck all wiring away and
(Figure 13)
Reconnect
Auxiliary Power Outlet plug.
Reinstall
20.
the two center dashboard fasteners and
the Fascia Panel.
21.
Lift
the rear of the center console above the floor an
inch or so and finish tucking all harness wiring underneath.
22.
Secure
the four torx fasteners that secure the center con-
sole to the floor.
23. You are now ready to test and enjoy your Headrest Monitor/DVD System. Be sure to read and understand the Vizualogic Owner’s Manual.
BLUE
with
PINK
the driver side
stripe)
Figure 14
Driver Side
12+ Power Outlet
Passenger Side
12+ Power Outlet
WIRE TAP CONNECTOR
Blue with Pink Stripe
WIRE TAP CONNE CTOR
Red with Green Stripe
Black with White Stripe
WIRE TAP CONNE CTOR
RED FROM POWER HARNESS
YELLOW FROM POWER HARNESS
BLACK FROM POWER HARNESS
Simplified Wire Illustration from Steps 18 and 19.
Page 5 www.quadratec.com
Loading...