Vizu ExtremeX Gimbal User manual

CONTENT

● Package List........................................................1

● Disclaimer and Warning.....................................2

● Safety Operation Guidelines...............................4

● Get to know the Stabilizer..................................6

● USB Connection..................................................7

●Mounting Camera, Checking Balance..................9

● Panel Introduction............................................10

●Operating Mode.................................................11

●Changing Orientation.........................................12

● App Operation, and Bluetooth Connection.......13

● Product Specification.........................................14

PACKAGE LIST

The product should be packed with following items (including this user
manual), If you are missing any items or components, please contact your
dealer immediately!

GIMBAL STABILIZER ×1
MICRO USB CABLE ×1

1

User Manual ×1

DISCLAIMER AND WARING

Thank you for purchasing our Stabilizer. Before you start PLEASE read this manual and become
familiar with Stabilizer’s components and operating modes to ensure proper operation. The
information contains herein affects your safety and your legal rights and responsibility.
Failure to read and follow the instructions and warnings may result in serious injury to you or damage
to your device or property.

By using this product, you hereby signify that you have read this document carefully and that you
understand and agree to abide by the terms and conditions herein. You agree that you are solely
responsible for you conduct while using this product and for any consequences thereof. You agree to
use this product only for purposes that are proper and in accordance with all terms, precautions,
practices, policies and guidelines our company has made and may make available.

Our company accepts no liability for damage, injury or any legal responsibility incurred directly or
indirectly from the use of this product. The user shall observe safe and lawful practices including, but
not limited to those set forth herein.

GLOSSARY

The following terms are used throughout the product literature to indicate various levels of potential
harm when operating this product.

■Warning: Procedures, which if not properly followed, may incur property damage, grave accident, or serious
injury.

■CAUTION: Procedures, which if not properly followed, may incur property damage and serious injury.

■NOTICE: Procedures, which if not properly followed, may incur property damage or minor injury.

DISCLAIMER AND WARING

WARNING:

Read the ENTIRE User guide to become familiar with the features of our Stabilizer before operating.
Failure to operate the product correctly can result in damage to the product or personal property,
and cause serious injury. This is a sophisticated product. It must be operated with caution and
common sense and requires some basic mechanical ability. In-correct Use of product in a safe and
responsible manner could result in injury or damage to the product or other property. This product is
not intended for use by children without direct adult supervision. DO NOT use with incompatible
components or in any way otherwise as mentioned or instructed in the product documents provided
by our company. This Safety Guidelines herein contain instructions for safety, operation and
maintenance. It is essential to read and follow all of the instructions and warnings in the user
manual, prior to assembly, setup or use, in order to operate the product correctly and avoid damage
or serious injury.

2

3

SAFETY OPERATION GUIDELINE

The Stabilizer should be used in temperatures from 0℃ to 40℃.
Use of the battery in environments above 40℃ can lead to a fire or explosion. Use of battery below
0℃ can lead to serious damage.

■CHARING THE BATTERY

1. Always use our company approved charger for charging. Our company takes no responsibility if
the battery is charged using Non-Our company charger.

2. Do not put the stabilizer near flammable materials or on flammable surfaces (such as carpet or
wood). Never leave the battery unattended during charging to prevent any accident.

3. Do not charge the battery immediately after use, when the Stabilizer temperature may be too
high. Do not charge the battery until it cools down to near room temperature .Charging the batte ry
with its temperature over 40℃ or lower than 5℃ may lead to leakage, overheating, or battery
damage.

4. Examine the charger and cable before use; make sure there is no damage to the enclosure, cord,
plug, or other parts. Never use a damaged charger. Do not clean the charger with denature alcohol
or other flammable solvents. Never use a damaged charger.

5. The Intelligent Battery will stop charging when it is full. Disconnect the batteries from the charger
when fully charged.

■STORAGE

1. DO NOT leave the Stabilizer near heat sources such as a furnace or heater, or expose inside of a
vehicle on hot days.

2. Store Stabilizer in dry environment, and never store the Stabilizer in any environment with
temperature of over 60℃.

3. Do not leave the Stabilizer unused for too long after it has been completely discharged to prevent
over-discharge of battery which may result in battery damage and permanent damage.

4

SAFETY OPERATION GUIDELINE

■CAUTION:

1. The Stabilizers a high -precision control device, damaged may be caused to stabilizer if it is
dropped or subject to external force, and this many result in malfunction.

2. Make sure the rotation of Stabilizer axes is not blocked by external force when the stabilizer is
power on.

3.The Stabilizer is not waterproof or water-resistant. Prevent contacts of any kind of liquid or clear
with.
Prevent contacts of any kind of liquid or clear with.
It is recommended to use dry cloth for cleaning.

4. Protect the Stabilizer from dust and sand during use.

■NOTICE

1. Hold the Stabilizer’s Handle still in when it is powering up to ensure it starts up successfully.

2. Make sure the batteries are fully charged before each time of use.

3. Discharge the battery to 40%~65% if it will NOT be used for over 10 days. This can greatly extend
the battery life.

4. Charge and Discharge the battery completely once every 3 months to keep it active.

5

②USB CONNECTION

6

7

①GET TO KNOW THE STABILIZER

The stabilizer is high-precision control device. Connect to APP, it has more face tracking, time-lapse
function, etc. which can offer you professional grade video.

14. Smartphone Clamp
Adjustment Knob

15.Shooting

16. Micro USB Charging Port

17. Power Output Port
(For charging of Smartphone)

8. Shifter Lever
(Zoom Control)

9. Status indicator

10. Tilt Motor

11. Arm Adjustment

12. Roll Balance Thumbscrew

13. Roll Motor

1. Smartphone Clamp

2. Pan Motor

3. Battery Level Indicator

4. Joystick

5. Power ON/OFF

6. 1/4 Thread screw
(For extension poles or tripods)

7. MODE Select

6

IN-USE CHARGING

Connect the Micro USB Port on the side
of stabilizer's handle to a power source
SUCH AS a power pack (not include) to
extend run-times.

The USB port at the bottom of the stabilizer
handle can be used for charging of your
Smartphone while in use on the Stabilizer.

■An L-shape charging connector is required
when the Smartphone is mounted
horizontally on the mobile clamp.

MOBILE CHARGING

⑤ OPERATING

To Power On

Step 2: Press & Hold the Power/Shooting button for 3-4 seconds until the Status
Indicator light flashes blue, and then turns ON Green finally.

③ MOUNTING CAMERA

8

9

Power ON/OFF

Place Smartphone to mounting clip,
as show. Slide the Smartphone all the
way to right until it touches Tilt
Motor.

NOTEDS: Proper adjustment of balance ensures better power saving during operation.

The stabilizer may still function well when the gravity center is not properly configured; however, it
may lead to more power consumption on the motors, and can greatly affect the torque output.

WARNING!

ALWAYS MOUNT YOUR CAMERA PRIOR TO
POWERING ON.
FAILURE TO DO CAN DAMAGE THE UNIT!

Indicator Light

If the Smartphone does not stay leveled when mounted, please do as following:

Step 1: Loosen the Roll balance Knob.
Step 2: Make small Adjustment t by sliding the horizontal arm, Until the mobile

intersects stabilizer with a 70-100 degree.
Step 3: Tighten the Thumb Screw after the phone is well balanced in level to ensure
normal operations.

④ CHECKING BALANCE

⑦ OPERATING MODES

SWITCHING STABLIZER MODES

Press the Power Button, The stabilizer enters Lock Mode each
time when powered on. (Default Mode)
Single Click Mode button to Switch into Pan Following Mode
Single Click the MODE button to enter into Pan&Tilt Follow

Mode.

Single
Press

Pan& Tilt

Follow

Mode

Pan

Following

mode

Locking
Mode

Single

Press

Single
Press

Tilt & Roll are locked.
Pan axis rotates (Left/Right)
smoothly with turn of
wrist.

Push Joystick up and down to
control the tilt of camera, use
joystick left and right to manual
pan left/right

Pan,Tilt, Roll axis are all locked.
The camera keep still and
stable, which mean Camera
cannot follow handle's
movement.

Push Joystick up and down to
control the tilt of camera, use joystick
left and right to manual
pan left/right

Roll axis is locked.
The camera pans (Left/right)
and tilts (Up/Down) are
following the movement of
camera.

Push Joystick up and down to
control the tilt of camera, use
joystick left and right to
manual pan left/right

Roll

Tilt
Pan

Tilt

Pan

10

11

Roll

Tilt

Pan

⑥ PANEL INTRUDUCTION

Status Indicator Light

Blue Light is always on- enough remaining battery
power
Power light will rapidly flash - low on charge

a. Connect the micro USB port to portable power source
such as USB power back to extend run-times.
b. Use a cable for Charging stabilizer when no power.

Use the zoom slider to control UP (Zoom In)
and Down (Zoom Out);

1. Blue Light - The Stabilizer is in operation, that the
control unit goes through to process an instruction

2. Green Light - Stabilizer has gone into working
condition.

3. Red Light:
Red Light is always on - low on charge-shut down.
Red Light is blinking rapidly - Stabilizer overload-shut
down.

Control movement UP/DOWN (Tilt Motor) and
LEFT/RIGHT (Pan Motor)

*The Joystick can be used in All 3 Modes

To Power on: Press & Hold the Power/Shooting
button for 3-4 seconds
until the Status Indicator light flashes blue, and
then turns ON Green finally.
To Power off: Press and holder the
POWER Button for 3 seconds
Double-click the front and back lens to switch；
Triple-click the photo and video switch.

After Bluetooth Connected between the mobile
and stabilizer, use SHOOT button to take
photos or video；double click can be taken
continuously

Single Press to cycle through the 3 Modes
that you set.Double click the MODE button to

bring the camera to its original position.

Joystick

Power ON/OFF

MODE

Micro USB Charging Port

Zoom Control

Pan & Tilt Follow Mode

Pan Following Mode

Lock Mode

Please make notes of each motor and operating
Mode details(showing on this page), as stabilizer
comes pro-program with 3 different mode

Roll

Micro USB Charging Port

Power Indicator Light Port

POWER Indicator Light

Power Output Port

Zoom Control (In APP control only)

Status Indicator Light

Joystick

Power ON/OFF

Shooting Function

MODE Button

⑧ CHANGE ORIENTATION

The Stabilizer comes with 2 different Way for Change Orientation

Keep the phone facing yourself and rotate the Stabilizer handle over 70 degrees in counterclockwise
direction, Stabilizer will enter vertical shooting Mode. (Phone camera upward)
Keep the phone facing yourself and rotate the Stabilizer handle over 70 degrees in clockwise direction,
Stabilizer enter vertical shooting. (Phone camera upward)

⑨ APP OPERATION & CONNECT TO BLUETOOTH

13

12

Step 1: Scan QR Code (For Andriod +iOS) and Download below APP for accessing.

Step2: Power on the stabilizer
Step 3:Turn on Bluetooth in your Smartphone settings menu.
Step 4: Open the Stabilizer APP, and search for the ‘Stabilizer ’Bluetooth signal by
selecting the Bluetooth icon in the pop-up screen
In the APP Menu, use the zoom slider to control UP(Zoom In) and Down(Zoom Out) , and
more function setting, such as Face Tracking, Smart Object Track, Panorama Shooting,
Time-Lapse.

Step 1: Press the Power button for 3-4 seconds, stabilizer will power on.
Step 2: Turn on Bluetooth in your Smartphone settings menu.
Step 3: After Bluetooth Connected between Smartphone and stabilizer, you can start
taking photo/Record video

Step 1: Loosen the Smartphone Clamp Thumbscrew and rotate the clamp to vertical direction
Step 2: Place your Smartphone on the Clamp
Step 3: Tighten the Clamp Thumbscrew to ensure normal operations.

Connect to Bluetooth

Connect to Stabilizer APP

Switching From Horizonta

Switching Mount

WARRANTY CARD

Warranty Period

1. The warranty period is 2 year from the original date of purchase. During the warranty period,
under normal use, our company will at its option, repair and/or replace parts which determined by
defective situation

2. Warranty this product against effects in material or workmanship when it belong Normal
consumer usage and conditions for the time periods.

Warranty does not cover:

1. Products subjected to unauthorized Maintenance, misuse, collision, neglect, mishandling, soaking,
accident, and unauthorized alteration.

2. Incorrect use of product: Removing serial number labels/tags

3. Products whose warranty has expired.

4. Products damaged due to force majeure, such as fire, flood, lighting, etc.

Warranty Claim Procedure

If failure or any problem occurs to your product after purchase, please contact a local agent for
assistant.

Latest Information

For the latest user manuals, tutorial video, firmware and calibration instruction, please visit your
dealer web page.
Many Stabilizer performances can be solved with a simple calibration sequences.

15

14

Product Specifications

Min. Standard Max. Remarks

Input Vol. 3.4V 3.7V 4.2V

Operation Current 15 0mA 150 0mA 300 0mA

Opration Temperature

0 40

Operation Time 12h

Well balanced with

camera mounted

Weight 423g

Pitch Angle Range 325°

Roll Angle Range 325°

Pan Angle Range 330°

Compatibale Models Smartphone with sizes under 6.0 G opro3/4/5/6

Controllable Pitch Angle -155° +155°

Controllable Roll Angle -30° +30°

Controllable Pan Angle -155° +155°

Payload 75~20 0g

Charing Time 3H

Charging Voltage 5V

Charing Current 1A

Power Output Voltage 5V

Power Output Current 1A

℃ ℃

⑩ PRODUCT SPECIFICATIONS

180°

16