Vizio JV50PHDTV10A Service Manual

Service Manual

Model #: VIZIO JV50P HDTV10A

V, Inc

320A Kalmus Drive Costa Mesa, CA 92626

TEL : [phone] FAX :[phone]

Top Confidential

Table of Contents

CONTENTS PAGE

Sections

1. Features 1-1

2. Specifications 2-1

3. On Screen Display 3-1

4. Factory Preset Timings

5. Pin Assignment

4-1

5-1

6. Main Board I/O Connections 6-1

7. Theory of Circuit Operation 7-1

8. Waveforms 8-1

9. Trouble Shooting 9-1

10. Block Diagram 10-1

11. Spare parts list 11-1

12. Complete Parts List 12-1

Appendix

1. Main Board Circuit Diagram

2. Main Board PCB Layout

3. Assembly Explosion Drawing

Block Diagram

VIZIO JV50P HDTV10A Service Manual

VINC Service Manual

VIZIO JV50P HDTV10A

COPYRIGHT © 2000 V, INC. ALL RIGHTS RESERVED.

IBM and IBM products are registered trademarks of International Business Machines
Corporation.

Macintosh and Power Macintosh are registered trademarks of Apple Computer, Inc.

VINC and VINC products are registered trademarks of V, Inc.

VESA, EDID, DPMS and DDC are registered trademarks of Video Electronics Standards
Association (VESA).

Energy Star is a registered trademark of the US Environmental Protection Agency (EPA).

No part of this document may be copied, reproduced or transmitted by any means for any
purpose without prior written permission from VINC.

FCC INFORMATION
This equipment has been tested and found to comply with the limits of a Class B digital device,
pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation. This equipment generates,
uses and can radiate radio frequency energy, and if not installed and used in accordance with
the instructions, may cause harmful interference to radio communications. However, there is
no guarantee that the interference will not occur in a particular installation. If this equipment
does cause unacceptable interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures -- reorient or relocate the receiving
antenna; increase the separation between equipment and receiver; or connect the into an
outlet on a circuit different from that to which the receiver is connected.

FCC WARNING
To assure continued FCC compliance, the user must use a grounded power supply cord and
the provided shielded video interface cable with bonded ferrite cores. Also, any unauthorized
changes or modifications to Amtrak products will void the user’s authority to operate this
device. Thus VINC Will not be held responsible for the product and its safety.

CE CERTIFICATION
This device complies with the requirements of the EEC directive 89/336/EEC with regard to
“Electromagnetic compatibility.”

SAFETY CAUTION
Use a power cable that is properly grounded. Always use the AC cords as follows – USA (UL);
Canada (CSA); Germany (VDE); Switzerland (SEV); Britain (BASEC/BS); Japan (Electric
Appliance Control Act); or an AC cord that meets the local safety standards.

VIZIO JV50P HDTV10A Service Manual

Chapter 1 Features

1. Built in TV channel selector for TV viewing

2. Simulatnueous display of PC and TV images

3. Connectable to PC’s analog RGB port

4. Built in HDTV, composite video, HDMI ,ATV out and DTV out ,

Audio AUX IN

5. Built in auto adjust function for automatic adjument of screen display

6. Smoothing function enables display of smooth texts and graphics even if

image with resolution lower than 1366x768 is magnified

7. Picture In Picture (PIP) function to show TV or VCR/DVD images

8. Power saving to reduce consumption power too less than 3W

9. On Screen Display: user can define display mode (i.e. color, brightness,

contrast, sharpness, backlight), sound setting, PIP, TV channel program,

aspect and gamma or reset all setting.

10. RF Modulation: Direct Sequence Spreading Spectrum (DSSS)

11. TX/RX distance: 10Meters (indoor with free space) min.

12. RX channel: 4 channels in 5.8GHz ISM band with auto scan and

synchronization functions.

13. Support 16bit, 32/44.1/48KHz digital audio transmission and receiving.

14. User unique ID pairing function.

15. RF channel Carrier Frequency:

Channel No. Center Frequency

1 5745MHz

2 5765MHz

3 5785MHz

4 5805MHz

CONFIDENTIAL – DO NOT COPY Page 1-1

File No. SG-0228

Chapter 2 Specification

1. PDP CHARACTERISTICS

PDP50X4 (50”WXGA PDP MODULE)

Item Specification

Active Screen Size

50 inch diagonal

Outline Dimension

Display Area

Pixel Pitch

Cell Pitch

Pixel Format 1366(H) × 768(V) (1pixel=3 RGB cells)

Number of Gradations (R)1,024 × (G)1,024 × (B)1,024 colors

Peak Brightness

Contrast Ratio Average 130:1 (In a bright room with 100Lux at center)

Viewing Angle(L/R/U/D) Free

Power Consumption Max. 400 W (Full-White)

Weight 20.4±0.5 Kg (Net 1EA)

2.Input Connectors

1190(H) × 700(V) × 58(D) ± 1mm

1106.5(H) × 622.1(V) ± 0.5mm

810 ㎛(H) × 810 ㎛(V)

270 ㎛ (H) × 810 ㎛ (V) (Green Cell basis)

Typical 1,500cd/㎡ (1/100 White Window pattern at

center)

Typical 15,000:1 (In a dark room 1/100 White Window

pattern at center)

RJ11, D-SUB15PIN (MINI, 3rows), HDMIX3, RCAX2 (component), RCAX2 (AUDIO

in), RCAX2 (composite), RCAX2 (AUDIO in), Tuner, SPDIF IN(Optical Audio)

3.Output Connectors

Stereo RCA Jack (Analog audio out) , SPDIF Out (Optical Audio)

4. POWER SUPPLY

Power Consumption: 550W MAX

Power OFF: to less than 3W MAX

SUBWOOFER POWER SUPPLY

Power Consumption: 70W MAX

Sleep mode(or TV off): to less than 3W MAX

CONFIDENTIAL – DO NOT COPY Page 2-1

File No. SG-0228

5.Speaker

Output 10W (max) X3

Wireless Speaker :

(1) Rear Right 10W(max)

(2) Rear Left 10W(max)

(3) Subwoofer 20W(max)

6. ENVIRONMENT

7-1. Operating Temperature: 5c~35c (Ambient)

7-2. Operating Humidity: Ta= 35 °C, 90%RH (Non-condensing)

7-3. Operating Altitude: 0 - 14,000 feet (Non-Operating)

7. DIMENSIONS (Physical dimension)

Width: 1241.0mm

Height: 856.3mm

Depth: 291.2mm

8. WEIGHT (Physical weight)

a. TV net 52.6kg

b. Spk net 8.0kg

c. TV and spk gross 72.0kg

9.Please pay attention to the followings when you use this PDP module.

9-1. MOUNTING PRECAUTIONS

(1) You must mount a module using holes arranged in four corners or four sides.

(2) You should consider the mounting structure so that uneven force (ex. Twisted

stress) is not applied to the module. And the case on which a module is mounted

should have sufficient strength so that external force is not transmitted directly to

the module.

(3) Please attach the surface transparent protective plate to the surface in order to

protect the polarizer.

Transparent protective plate should have sufficient strength in order to the resist

external force.

(4) You should adopt radiation structure to satisfy the temperature specification.

CONFIDENTIAL – DO NOT COPY Page 2-2

File No. SG-0228

(5) Acetic acid type and chlorine type materials for the cover case are not desirable

because the former generates corrosive gas of attacking the polarizer at high

temperature and the latter causes circuit break by electro-chemical reaction.

(6) Do not touch, push or rub the exposed polarizes with glass, tweezers or

anything harder than HB pencil lead. And please do not rub with dust clothes

with chemical treatment.

Do not touch the surface of polarizer for bare hand or greasy cloth.(Some

cosmetics are detrimental to the polarizer.)

(7) When the surface becomes dusty, please wipe gently with absorbent cotton or

other soft materials like chamois soaks with petroleum benzene. Normal-hexane

is recommended for cleaning the adhesives used to attach front / rear polarizers.

Do not use acetone, toluene and alcohol because they cause chemical damage

to the polarizer.

(8) Wipe off saliva or water drops as soon as possible. Their long time contact with

polarizer causes deformations and color fading.

(9) Do not open the case because inside circuits do not have sufficient strength.

9-2. OPERATING PRECAUTIONS

(1) The spike noise causes the mis-operation of circuits. It should be lower than

following voltage :

V=±200mV(Over and under shoot voltage)

(2) Response time depends on the temperature. (In lower temperature, it becomes

longer.)

(3) Be careful for condensation at sudden temperature change. Condensation

makes damage to polarizer or electrical contacted parts. And after fading

condensation, smear or spot will occur.

(4) When fixed patterns are displayed for a long time, remnant image is likely to

occur.

(5) Module has high frequency circuits. System manufacturers shall do sufficient

suppression to the electromagnetic interference. Grounding and shielding

methods may be important to minimize the interference.

CONFIDENTIAL – DO NOT COPY Page 2-3

File No. SG-0228

9-3. HANDLING PRECAUTIONS FOR PROTECTION

(1) The protection film is attached to the bezel with a small masking tape. When the

protection film is peeled off, static electricity is generated between the film and

polarizer. This should be peeled off slowly and carefully by people who are

electrically grounded and with well ion-blown equipment or in such a condition,

etc.

(2) When the module with protection film attached is stored for a long time,

sometimes there remains a very small amount of glue still on the bezel after the

protection film is peeled off.

(3) You can remove the glue easily. When the glue remains on the bezel surface or

its vestige is recognized, please wipe them off with absorbent cotton waste or

other soft material like chamois soaked with normal-hexane.

CONFIDENTIAL – DO NOT COPY Page 2-4

File No. SG-0228

Chapter 3 On Screen Display

Main unit button

Power

MENU

CH ▲

CH ▼

VOL +

VOL -

Input

On Screen Display

TV Source

A. PICTURE：

a. PICTURE MODE

(CUSTOM/ STANDARD / MOVIE / GAME)

b. BACKLIGHT (0~100)

c. BRIGHTNESS (0~100)

d. CONTRAST (0~100)

e. COLOR (0~100)

f. TINT (-32~32)

g. SHARPNESS (0~100)

h. COLOR TEMPERATURE

(CUSTOM/COOL/NORMAL/WARM)

i. ADVANCED VIDEO

i-1. DNR(OFF/LOW/MEDIUM/STRONG)

i-2. BLACK LEVEL EXTENDER (ON/OFF)

i-3. WHITE PEAK LIMITATOR (ON/OFF)

i-4 CTI(OFF/LOW/MEDIUM/STRONG)

i-5 FLESH TONE (ON/OFF)

i-6 ADAPTIVE LUMA (ON/OFF)

CONFIDENTIAL – DO NOT COPY Page 3-1

File No. SG-0228