VL120026
6-input Seamless Scaler Switcher &
HDBaseT Receiver
User Manual
6-input Seamless Scaler Switcher & HDBaseT Receiver
Preface
Read this user manual carefully before using this product. Pictures shown in this manual
is for reference only, different model and specifications are subject to real product.
This manual is only for operation instruction only, not for any maintenance usage. The
functions described in this version are updated till May 2017. In the constant effort to
improve our product, we reserve the right to make functions or parameters changes
without notice or obligation. Please refer to the dealers for the latest details.
All product function is valid till 2017-5-3.
Trademarks
Product model, VivoLink are trademarks of EET Europarts A/S. Any other trademarks
mentioned in this manual are acknowledged as the properties of the trademark owner.
No part of this publication may be copied or reproduced without the prior written consent
of EET Europarts A/S.
FCC Statement
This equipment generates, uses and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions, may cause harmful interference
to radio communications. It has been tested and found to comply with the limits for a
Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed
to provide reasonable protection against harmful interference in a commercial
installation.
Operation of this equipment in a residential area is likely to cause interference, in which
case the user at their own expense will be required to take whatever measures may be
necessary to correct the interference.
Any changes or modifications not expressly approved by the manufacture would void
the user’s authority to operate the equipment.
6-input Seamless Scaler Switcher & HDBaseT Receiver
SAFETY PRECAUTIONS
To insure the best from the product, please read all instructions carefully before using
the device. Save this manual for further reference.
Unpack the equipment carefully and save the original box and packing material for
possible future shipment
Follow basic safety precautions to reduce the risk of fire, electrical shock and injury
to persons.
Do not dismantle the housing or modify the module. It may result in electrical shock
or burn.
Using supplies or parts not meeting the products’ specifications may cause damage,
deterioration or malfunction.
Refer all servicing to qualified service personnel.
To prevent fire or shock hazard, do not expose the unit to rain, moisture or install this
product near water.
Do not put any heavy items on the extension cable in case of extrusion.
Do not remove the housing of the device as opening or removing housing may
expose you to dangerous voltage or other hazards.
Install the device in a place with fine ventilation to avoid damage caused by
overheat.
Keep the module away from liquids.
Spillage into the housing may result in fire, electrical shock, or equipment damage. If
an object or liquid falls or spills on to the housing, unplug the module immediately.
Do not twist or pull by force ends of the optical cable. It can cause malfunction.
Do not use liquid or aerosol cleaners to clean this unit. Always unplug the power to
the device before cleaning.
Unplug the power cord when left unused for a long period of time.
Information on disposal for scrapped devices: do not burn or mix with general
household waste, please treat them as normal electrical wastes.
6-input Seamless Scaler Switcher & HDBaseT Receiver
Contents
1. Introduction ................................................................................................................. 1
1.1 Brief Introduction ............................................................................................... 1
1.2 Features ............................................................................................................ 1
1.3 Package List ...................................................................................................... 2
2. Panel Description ........................................................................................................ 3
2.1 Seamless Scaler Switcher ................................................................ ................. 3
2.2 HDBaseT Receiver ............................................................................................ 5
3. System Connection ................................ ................................ ................................ ..... 7
3.1 Usage Precautions ............................................................................................ 7
3.2 System Diagram ................................................................................................ 7
3.3 Connection Procedure ....................................................................................... 7
4. Button Control ............................................................................................................. 9
4.1 Manual-Switching .............................................................................................. 9
4.2 Auto-Switching ................................................................................................... 9
4.3 Volume Adjusting ............................................................................................... 9
5. IR Control .................................................................................................................. 10
5.1 IR Remote ....................................................................................................... 10
5.2 Control Far-end Display Device ....................................................................... 11
5.3 Control Local Source Device ........................................................................... 11
5.4 CEC Function .................................................................................................. 12
6. RS232 Control .......................................................................................................... 14
6.1 RS232 Connection .......................................................................................... 14
6.2 Installation/uninstallation of RS232 Control Software ...................................... 15
6.3 RS232 Communication Commands ................................................................ 17
6.3.1 RS232 Control Mode Switching ............................................................. 17
6.3.2 Input Signal Switching ........................................................................... 17
6.3.3 Audio Adjusting ...................................................................................... 18
6.3.4 VGA Scaling Configuration .................................................................... 20
6.3.5 Output Image Adjusting ......................................................................... 20
6.3.6 Auto Power-off Setup ............................................................................. 22
6.3.7 OSD Menu Control ................................................................................ 23
6-input Seamless Scaler Switcher & HDBaseT Receiver
6.3.8 CEC Input Commands ........................................................................... 24
6.3.9 CEC Output Commands ........................................................................ 24
6.3.10 EDID Configuration ................................................................ .............. 25
6.3.11 HDCP Compliance ............................................................................... 26
6.3.12 Device Setup ....................................................................................... 26
7. OSD Menu Control ................................................................................................... 28
7.1 OPTIONS ........................................................................................................ 28
7.2 PICTURE ......................................................................................................... 29
7.3 SETUP............................................................................................................. 30
8. Web-based GUI Control ............................................................................................ 31
8.1 Control Menu ................................................................................................... 31
8.2 Configuration Menu ......................................................................................... 33
8.3 RS232 Control Menu ....................................................................................... 35
8.4 Password Menu ............................................................................................... 36
8.5 Web-based GUI Update .................................................................................. 36
9. Specification ............................................................................................................. 37
9.1 Seamless Scaler Switcher ................................................................ ............... 37
9.2 HDBaseT Receiver .......................................................................................... 38
10. Panel Drawing ........................................................................................................ 39
11. Troubleshooting & Maintenance ............................................................................. 40
12. After-sales Service .................................................................................................. 41
6-input Seamless Scaler Switcher & HDBaseT Receiver
1
1. Introduction
1.1 Brief Introduction
This product is a professional Scaler Switcher Kit consists of multi-format Seamless
Scaler Switcher and HDBaseT Receiver.
The Scaler Switcher scales HDMI/DP/VGA video signals to an HDMI and HDBaseT
output simultaneously. HDBaseT output supports PoH and can connect to a compatible
HDBaseT Receiver. With 1 IR IN and 1 IR OUT and 1 RS232, the IR and RS232 control
signals can be transmitted bi-directionally between the Scaler Switcher and a
compatible HDBaseT Receiver. The Scaler Switcher can be controlled either by front
panel buttons, IR Remote, RS232 or web-based GUI. With a balanced stereo audio
output for audio reinforcement, the Scaler Switcher can be handle in a myriad of A/V
applications.
1.2 Features
Compliant with HDMI1.4& HDCP2.2.
VGA video supports C-video, YPbPr and VGA.
Supports PoH for simplified wiring.
The transmission distance between the Scaler Switcher and HDBaseT Receiver
can up to 70m at 1080p.
Supports CEC, with commands to enable/disable this function.
Supports Seamless switching and auto-switching function.
Controllable via front panel buttons, IR Remote, RS232 & Web-based GUI.
Powerful OSD (on screen display) control.
Bi-directional IR & RS232 control.
Supports CEC.
Supports MHL.
Output resolutions selectable to assure preferred output, and supports various
output resolutions, such as 1920x1200, 1920x1080, 1600x1200, 1600x900,
1360x768, 1280x800, 1280x720, 1024x768.
Supports online software upgrading.
6-input Seamless Scaler Switcher & HDBaseT Receiver
2
1.3 Package List
Part 1
1 x Seamless Scaler Switcher
2 x Mounting Ears with 4 Screws
2 x Long Mounting Ears with 6 Screws (Optional)
1 x Power Adapter (24VDC,2.71A)
4 x Plastic Cushions
1 x IR Remote
1 x IR Receiver (5V with carrier wave)
1 x IR Emitter
1 x VGA Converting Cable (VGA to YPbPr)
2 x 3-Pin Phoenix Connectors
1 x 5-Pin Phoenix Connector
Part 2
1 x HDBaseT Receiver
2 x Mounting Ears with 4 Screws
4 x Plastic Cushions
1 x User Manual
Note：Please confirm if the product and the accessories are all included, if not, please
contact with the dealers.
6-input Seamless Scaler Switcher & HDBaseT Receiver
3
2. Panel Description
2.1 Seamless Scaler Switcher
Front Panel
① Built-in IR Receiver.
② Power Indicator- RED when the device is in standby, GREEN when device is
powered on and no indicator when there is no power to device.
③ 1-HDMI/MHL input selector and activity LED/ Left key for OSD.
④ 2-HDMI input selector and activity LED/ Right key for OSD.
⑤ 3-HDMI input selector and activity LED/ Up key for OSD.
⑥ 4-HDMI input selector and activity LED/ Down key for OSD.
⑦ 5-DP input selector and activity LED/ ENTER key for OSD.
⑧ 6-VGA input selector and activity LED/ OSD menu button.
⑨ Auto switching selector and activity LED.
Press this to enter or exit auto-switching mode.
Long-press this button 3 seconds or more to reset output resolution to 720p or to
activate HDMI and HDBT outputs if they have been turned off.
Note: When you set any VGA port to C-video or YPbPr in Manual-switching mode,
the system will not be able to enter Auto-switching mode.
⑩ Volume knob for variable audio control- Push knob in to toggle between ‘MIX’ and
‘Source’ control.
VOLUME
IR
SOURCE
MIX
1-HDMI/M HL 6-VGA
5-DP3-HDMI
4-HDMI2-HDMI AUTO
RES RESET/ 3sMENU/3sENTER
1
2
3
4
5
6
7
8
9
10
6-input Seamless Scaler Switcher & HDBaseT Receiver
4
Rear Panel
① INPUTS
- Video input ports: 1 HDMI/MHL, 3 HDMI inputs, 1 DP and 1 VGA.
- Audio input ports: 1 VGA auxiliary audio input.
② OUTPUTS
- HDMI output: HDMI video output port.
- HDBaseT output: Support PoH. Connect with a compatible HDBaseT Receiver to
transmit AV signal, IR or RS232 control signal.
③ AUDIO IN
- MIX: 3-Pin phoenix connector for line audio input.
- 1-AUDIO& 2-AUDIO: 3.5mm mini jacks for line audio input.
④ CONTROL
IR IN & IR OUT: Connect with IR Receiver and Emitter to control devices via IR.
IR EYE: Connect with the IR Receiver (with carrier wave only) to control this
Scaler Switcher via the including IR Remote.
FIRMWARE: Type-A USB port for updating system firmware or loading
customized EDID data.
RS232: Serial port, 3-pin phoenix connector, connect with a control device (such
as PC) to control the Scaler Switcher or other devices connected with HDBaseT
Receiver.
TCP/IP: Ethernet port, connect with PC to control the Scaler Switcher via GUI.
⑤ AUDIO OUT - Stereo balanced L/R audio output.
⑥ DC 24V - Locking power port, connect 24V DC power adapter.
Tx Rx
DC 24V
HDBT
L R
HDMI1-HD MI/M HL
IR EYEIR IN IR OUT TCP/ IPRS23 2
AUDIO IN
1-AU DIO 2-AU DIO
L R
MIX
6-VG A2-HD MI
3-HD MI
4-HD MI
5-DP
CONTROL AUDIO OUT POWER
INPUTS
OUTPUTS
1
2
3
4
5
6
6-input Seamless Scaler Switcher & HDBaseT Receiver
5
2.2 HDBaseT Receiver
Front Panel
① RS232 Mode switcher
CTRL: RS232 pass-through control mode;
UPDATE A: Update Valens IC program, connect a PC to the RS232 port, and
then double-click the update file (.bat).
UPDATE B: Update the IC program which is used for de-embedding audio, the
upgrade method is the same as the above UPDATE A.
② Link status LED - OFF: No Link / GREEN: Link successful.
③ HDCP compliant LED - OFF: No HDMI traffic/GREEN: Traffic with HDCP/Blinking
GREEN: Traffic without HDCP.
④ Power LED - RED when device is powered on and no indicator when there is no
power to device.
Rear Panel
① RS232 connector- If one is connected with control device (e.g. PC), and the other
should be connected with the third-party that need to be controlled.
② IR IN - Work with far-end IR OUT port, connect with IR Receiver (with carrier) to
collect IR signal to control far-end display device from local.
③ IR OUT - Work with far-end IR IN port, connect with IR Emitter to send IR signal to
control input source device.
④ HDMI OUT - HDMI type A connector, connect to display.
HDCPLINK
UPDATE A
CTRL
UPDATE B
1
2
3
4
Tx Rx
RS232 DC 12VIR OUT HDMI OUT
HDBT IN
AUDIO
OUT
OPTICAL
OUT
IR IN
COAX
OUT
1
2
3
4
5
6
7
8
9
6-input Seamless Scaler Switcher & HDBaseT Receiver
6
⑤ AUDIO OUT -3.5mm stereo audio jack, connect to analog stereo audio device.
⑥ COAX OUT - Coaxial audio connector, connect to digital audio device.
⑦ OPTICAL OUT - Optical audio connector, connect to optical audio devices.
⑧ HDBT IN - Connect to the HDBT OUT socket on HDBaseT Transmitter or Matrix
Switcher via CAT5e/6a/7 cable, support unidirectional PoH technology.
⑨ DC 12V power port - Connect to 12VDC power adaptor, or it can be powered via the Scaler
Switcher by PoH technology.
6-input Seamless Scaler Switcher & HDBaseT Receiver
7
3. System Connection
3.1 Usage Precautions
System should be installed in a clean environment and has a prop temperature
and humidity.
All of the power switches, plugs, sockets and power cords should be insulated and
safe.
All devices should be connected before power on.
3.2 System Diagram
3.3 Connection Procedure
Step1. Connect HDMI source devices (e.g. Blue-ray DVD) to 1~4 HDMI input ports with
HDMI cables.
Step2. Connect a DP source device (e.g. MacBook) to DP input port with DP cable.
Step3. Connect a VGA source device (e.g. Laptop) to VGA input port with VGA cable
and VGA audio input port with audio cable.
Laptop
TVDVD
Pad MacBook
Tx Rx
DC 24V
HDBT
L R
HDMI1-HDMI/M HL
IR EYEIR IN IR OUT TCP/IPRS232
AUDIO IN
1-AUDIO 2- AUDIO
L R
MIX
6-VGA2-HDMI 3-HDMI 4-HDMI 5-DP
CONTRO L AUDIO OU T POWER
INPUTS OUTPUTS
IR Emitter
Projector Remote
Speaker
Scaler Switcher Remote
Control System
Laptop
HDBaseT Receiver
DVD Remote IR Receiver
Projector
IR Emitter
IR Receiver
Router
HDMI:
VGA:
DP:
Audio:
Ethernet:
HDBaseT:
IR Control:
RS232:
OK
INPUT 1
INPUT 5
INPUT 2
INPUT 3
INPUT 4
Scaler Switcher
AUTO
MUTE
VOL
6-input Seamless Scaler Switcher & HDBaseT Receiver
8
Step4. Connect audio source device to the audio input port with audio cable.
Step5. Connect a HDMI display device to HDMI output port with HDMI cable.
Step6. Connect HDBaseT Receiver to HDBT output port with twisted pair.
Step7. Connect speaker, headphone or AV amplifier to AUDIO OUTPUT port.
Step8. Connect control device (e.g. PC) to the TCP/IP port, the Scaler Switcher can
be controlled via web-based GUI.
Step9. Connect control device (e.g. PC, control system) to the RS232 port of the
Scaler Switcher or HDBaseT Receiver (bi-directional RS232 control, either end is
available).
Step10. Connect IR Receiver to the IR EYE port, the Scaler Switcher can be
controlled via IR Remote. For more details, please refer to 5. IR Control.
Step11. Both the Scaler Switcher and HDBaseT Receiver have IR IN and OUT. When
one model is connected with IR Receiver, the other model should connect with an
IR Emitter.
For example: When “IR IN” of the Scaler Switcher connects with an IR Receiver,
the IR Emitter must connect to IR OUT of HDBaseT Receiver.
The IR signal can be transmitted bi-directionally between the Scaler
Switcher and HDBaseT Receiver.
Step12. Connect DC24V power adaptor to the power port (HDBaseT Receiver can be
powered by the Scaler Switcher with PoH function).
Note: If the power adapter is connecting with HDBaseT Receiver, the Scaler Switcher
can’t be powered from HDBaseT Receiver.
6-input Seamless Scaler Switcher & HDBaseT Receiver
9
4. Button Control
Front panel buttons can be used for switching operations and volume adjusting.
4.1 Manual-Switching
Press 1-HDMI/MHL, 2-HDMI, 3-HDMI, 4-HDMI, 5-DP, 6-VGA on front panel to select the
corresponding input source.
4.2 Auto-Switching
Press AUTO to enter in auto-switching mode, and the auto-switching mode abides by
the following principles:
New input
Once detecting a new input signal, the switcher would switch to this new signal
automatically.
Rebooting device
The Scaler Switcher have the ability to save the last configuration before losing
power. If the last switching mode is auto-switching, once rebooted, the switcher will
automatically enter auto-switching mode, then detect all inputs and memorize their
connection status for future rebooting using. If the last displayed signal is still
available, the unit will output the signal. If not, the unit will detect all the input signals
wit priority from 1-HDMI/MHL to 6-VGA. When detected the first signal, it will transfer
to output.
Signal removing
Once removing the current display signal, the Scaler Switcher will detect all input
signals with priority from 1-HDMI/MHL to 6-VGA. It will transfer the signal firstly
detected to be available to output devices.
Note: Auto-switching function works only when inputting new signal, removing a signal
or power rebooting. With any VGA port set to C-video or YPbPr, the system will be not
able to enter in Auto-switching mode.
4.3 Volume Adjusting
Press Volume knob to select MIX or Source audio to adjust, the corresponding LED will
turn green and keep on, and then move the volume knob in clockwise or anti-clockwise
direction to turn up/down sound volume.
6-input Seamless Scaler Switcher & HDBaseT Receiver
10
5. IR Control
5.1 IR Remote
Connect IR receiver to IR EYE port, the Scaler Switcher cans be controlled by using the
including IR Remote. As CEC function, it is able to use the IR Remote to turn on/off the
HDMI source or Display.
① Enter/ exit standby mode.
② Input channel selection buttons (1~6): Select
video source via pressing corresponding button
(audio switched following the corresponding video
signal).
③ Mute/ unmute audio
④ VOL: Volume adjusting button. After pressing
this button, the volume adjusting menu will be
showed on Display, and then press UP/DOWON
button to turn up/down volume.
⑤ Auto button: Enter/Exit auto-switching mode.
⑥ OK: confirm button; Navigation buttons:
UP/DWON/LEFT/ RIGHT button, for value setting
or page-turn.
⑦ Exit button: Exit OSD menu or current
operation.
⑧ Enter OSD menu or return to previous menu.
OK
1-HDMI
5-DP
2-HDMI
3-HDMI
4-HDMI
Scaler Switcher
6-VGA
MUTE
AUTO VOL
1
2
3
6
7
4
5
8
6-input Seamless Scaler Switcher & HDBaseT Receiver
11
5.2 Control Far-end Display Device
Connect an IR Receiver to IR IN port on the Scaler Switcher and connect IR Emitter to
the IR OUT port on the HDBaseT Receiver, the far-end device(such as Projector) can be
control by its IR Remote.
5.3 Control Local Source Device
Connect an IR Emitter to IR OUT port on the Scaler Switcher and connect IR Receiver
to the IR IN port on the HDBaseT Receiver, the source device (such as DVD) can be
control by its IR Remote.
Tx Rx
DC 24V
HDBT
L R
HDMI1-HDMI /MHL
IR EYEI R IN IR OUT TCP/IPRS23 2
AUDIO I N
1-AUDI O 2-A UDIO
L R
MIX
6-VGA2-HDMI
3-HDMI
4-HDMI
5-DP
CONTR OL AUDIO O UT POWER
INPUT S OUTPU TS
Projector Remote
DVD
HDBaseT Receiver
Projector
IR Emitter
IR Receiver
HDBaseT:
IR Control:
HDMI:
6-input Seamless Scaler Switcher & HDBaseT Receiver
12
5.4 CEC Function
The Scaler Switcher supports CEC, it can be turned on/ off by sending RS232
commands or OSD menu operations. The default setting is ON.
Commands pertaining to CEC: “50686%” (enable CEC) and “50687%” (disable CEC)
HDMI INPUT ports support CEC, if the connected source devices also support CEC and
their CEC are on, users can control the source device and display via the IR Remote of
the Scaler Switcher.
Tx Rx
DC 24V
HDBT
L R
HDMI1-HDMI /MHL
IR EYEIR IN IR OUT TCP/IPRS232
AUDIO I N
1-AUDI O 2-AUDI O
L R
MIX
6-VGA2-HDMI
3-HDMI
4-HDMI
5-DP
CONTR OL AUDIO O UT P OWER
INPUT S OUTPU TS
IR Emitter
DVD
HDBaseT Receiver
Projector
DVD Remote IR Receiver
HDBaseT:
IR Control:
HDMI:
6-input Seamless Scaler Switcher & HDBaseT Receiver
13
The working status related to CEC and STANDBY is showed as below:
Situation
Working Status
CEC: on, Standby: on
Press STANDBY button on IR Remote, the Scaler Switcher
enters in standby mode, so do all HDMI source devices and
display.
Press STANDBY button again on IR Remote, the Scaler
Switcher exits standby mode, the previous selected HDMI
input source device and display start working too.
CEC: on, Standby: off
Press STANDBY button on IR Remote, the Scaler Switcher
enters in standby mode, HDMI source devices and display
keep on.
CEC: on
Use , , , and buttons on IR
Remote to control HDMI source device.
CEC: off
Unable to control HDMI source device and display through IR
Remote
Tx Rx
DC 24V
HDBT
L R
HDMI1-HDMI /MHL
IR EYEIR IN IR OUT TCP/IPRS232
AUDIO I N
1-AUDI O 2 -AUDIO
L R
MIX
6-VGA2-HDMI 3-HDMI 4 -HDMI 5-D P
CONTR OL AUDIO O UT PO WER
INPUT S OUTPU TS
TV
TV
Scaler Switcher Remote
HDBaseT Receiver
IR Receiver
DVD
HDMI:
HDBaseT:
IR Control:
OK
INPUT 1
INPUT 5
INPUT 2 INPUT 3
INPUT 4
Scaler Switcher
AUTO
MUTE
VOL
6-input Seamless Scaler Switcher & HDBaseT Receiver
14
6. RS232 Control
As RS232 can be transmitted bi-directionally between the Scaler Switcher and
HDBaseT Receiver, so it is able to control a third-party device from local or control the
Scaler Switcher from remote. The baud rate support 2400, 4800, 9600(default), 19200,
38400, 57600 or 115200.
6.1 RS232 Connection
There are two RS232 control modes can be chosen via RS232 commands
(50787%/50788%).
① Control Scaler Switcher or Third-party Device from Local
Firstly, according the following connection diagram to connect all devices as needed.
Secondly, send command 50787% (serial control mode 1, factory default) via RS232
communication software.
Lastly, send the right command of the Scaler Switcher or other remote RS232 device
connected in present system.
Tx Rx
DC 24V
HDBT
L R
HDMI1-HDMI /MHL
IR EYEIR IN IR OUT TCP/I PRS232
AUDI O IN
1-AUD IO 2-AU DIO
L R
MIX
6-VGA
2-HDMI
3-HDMI 4-HDMI 5-DP
CONT ROL AUDI O OUT POWE R
INPU TS OUTP UTS
Third-party device
Laptop
HDBaseT Receiver
HDBaseT:
RS232:
6-input Seamless Scaler Switcher & HDBaseT Receiver
15
② Control Scaler Switcher or Third-party Device form Remote
Firstly, according the following connection diagram to connect all devices as needed.
Secondly, send command 50788% via RS232 communication software.
Lastly, send the right command to control the Scaler Switcher:
6.2 Installation/uninstallation of RS232 Control Software
Installation Copy the control software file to the computer connected with the
Scaler Switcher.
Uninstallation Delete all the control software files in corresponding file path.
Basic Settings:
First to connect the Scaler Switcher with all input devices and output devices needed,
then to connect it with a computer which is installed with RS232 control software.
Double-click the software icon to run this software.
Here we take the software CommWatch.exe as example. The icon is showed as below:
Tx Rx
DC 24V
HDBT
L R
HDMI1-HD MI/MHL
IR EYEIR IN IR OUT TCP/IPRS23 2
AUDI O IN
1-AUD IO 2-AU DIO
L R
MIX
6-VGA
2-HDMI
3-HDMI 4-HDMI 5-DP
CONT ROL AUDIO O UT POWE R
INPU TS OUTPU TS
Third-party device
Laptop
HDBaseT Receiver
HDBaseT:
RS232:
6-input Seamless Scaler Switcher & HDBaseT Receiver
16
The interface of the control software is showed as below:
Please set the parameters of COM number, bound rate, data bit, stop bit and the parity
bit correctly, and then you are able to send command in Command Sending Area.
Parameter Configuration area
Monitoring area, indicates if the
command sent works.
Command Sending area
6-input Seamless Scaler Switcher & HDBaseT Receiver
17
6.3 RS232 Communication Commands
Communication protocol: RS232 Communication Protocol
Baud rate: 9600 Data bit: 8 Stop bit: 1 Parity bit: none
6.3.1 RS232 Control Mode Switching
Command
Function
Feedback Example
50787%
Enable RS232 control mode 1: Control
the Scaler Switcher or third-party device
from local.
RS232 Mode 1: RS232
Control Scaler & Remote
50788%
Enable RS232 control mode 2: Control
the Scaler Switcher or third-party device
from remote.
RS232 Mode 2: RS232
Control Scaler
/+[X]:******
Set communication between PC and
HDBaseT receiver.
X is for baud rate, its value ranges
from 1 to 7 (1--2400, 2--4800,
3--9600, 4--19200, 5--38400,
6—57600, 7--115200)
***** is for data (max 48 Byte)
None
6.3.2 Input Signal Switching
Command
Function
Feedback Example
50701%
Switch to 1-HDMI/MHL input.
Switch to HDMI 1
50702%
Switch to 2-HDMI input.
Switch to HDMI 2
50703%
Switch to 3-HDMI input.
Switch to HDMI 3
50704%
Switch to 4-HDMI input.
Switch to HDMI 4
50705%
Switch to 5-DP input.
Switch to DP
50706%
Switch to VGA/YPbPr/AV input.
Switch to VGA
50680%
Set the signal format to VGA for 6-VGA
input.
Input 6 Set & Switch to VGA
50681%
Set the signal format to YPbPr for 6-VGA
input.
Input 6 Set & Switch to
YPbPr
50682%
Set the signal format to AV(C-video) for
6-VGA input.
Input 6 Set & Switch to AV
50631%
Get the input source.
Input: xx (xx= HDMI1/
6-input Seamless Scaler Switcher & HDBaseT Receiver
18
HDMI2/ HDMI3/ HDMI4/
DP/VGA/ YPbPr/ AV)
50785%
Enable auto-switching.
Auto Switch
50786%
Disable auto-switching.
Manual Switch
6.3.3 Audio Adjusting
Command
Function
Feedback Example
50600%
Mute source audio.
Source Mute
50601%
Unmute source audio.
Source Unmute
50751%
Get the Source mute status.
Source Mute/Source Unmute
50602%
Turn up the source audio volume
Source Volume: xx
(xx=00~60)
50603%
Turn down the source audio volume.
Source Volume: xx
(xx=00~60)
501xx%
Set the source audio volume.
Source Volume: xx
(xx=00~60)
50720%
Mute Source & Line audio.
Line Mute
Source Mute
50721%
Unmute Source & Line audio.
Line Unmute
Source Unmute
50722%
Mute Line audio.
Line Mute
50723%
Unmute Line audio.
Line Unmute
50752%
Get the Line mute status
Line Mute/Line Unmute
50724%
Turn up the Line audio volume.
Line Volume: xx (xx=00~60)
50725%
Turn down the Line audio volume.
Line Volume: xx (xx=00~60)
50630%
Get the volume level.
Source Volume: xx
(xx=00~60)
Line Volume: xx (xx=00~60)
508xx%
Set the Line audio volume.
Line Volume: xx (xx=00~60)
50726%
Disable VGA audio.
VGA Audio Mute
50727%
Enable VGA audio.
VGA Audio Unmute
50712%
Get the audio input sources for VGA.
VGA Audio Mute/VGA Audio
6-input Seamless Scaler Switcher & HDBaseT Receiver
19
Unmute
50660%
Disable 1-HDMI audio.
HDMI1 Audio Mute
50661%
Enable 1-HDMI audio.
HDMI1 Audio Unmute
50662%
Disable 2-HDMI audio.
HDMI2 Audio Mute
50663%
Enable 2-HDMI audio.
HDMI2 Audio Unmute
50664%
Disable 3-HDMI audio.
HDMI3 Audio Mute
50665%
Enable 3-HDMI audio.
HDMI3 Audio Unmute
50666%
Disable 4-HDMI audio.
HDMI4 Audio Mute
50667%
Enable 4-HDMI audio.
HDMI4 Audio Unmute
50668%
Disable DP audio.
DP Audio Mute
50669%
Enable DP audio.
DP Audio Unmute
50941%
Disable MIX audio.
MIX Audio Disable
50942%
Enable MIX audio.
MIX Audio Enable
50943%
Disable 1-AUDIO audio.
1-AUDIO Disable
50944%
Enable 1-AUDIO audio.
1-AUDIO Enable
50945%
Disable 2-AUDIO audio.
2-AUDIO Disable
50946%
Enable 2-AUDIO audio.
2-AUDIO Enable
50659%
Check input HDMI audio status.
HDMI1 Audio Unmute/HDMI1
Audio Mute
HDMI2 Audio Unmute/HDMI2
Audio Mute
HDMI3 Audio Unmute/HDMI3
Audio Mute
HDMI4 Audio Unmute/HDMI4
Audio Mute
DP Audio Unmute/DP Audio
Mute
50947%
Check external audio input status (MIX,
1-AUDIO, 2-AUDIO).
MIX Disable/MIX Enable
1-AUDIO Disable/1-AUDIO
Enable
2-AUDIO Enable/2-AUDIO
Enable
6-input Seamless Scaler Switcher & HDBaseT Receiver
20
50648%
Enable HDMI embedded audio output.
Embedded Audio Output:
enable
50649%
Disable HDMI embedded audio output.
Embedded Audio Output:
disable
6.3.4 VGA Scaling Configuration
The default output resolution for VGA is 1920x1080. Below is a list of the output
resolutions the built-in scaler can output.
Command
Function
Feedback Example
50619%
Set the output resolution to 1360X768
HD.
Resolution: 1360x768
50626%
Set the output resolution to 1024X768
XGA.
Resolution: 1024x768
50627%
Set the output resolution to 1280X720
720P.
Resolution: 1280x720
50628%
Set the output resolution to 1280X800
WXGA.
Resolution: 1280x800
50629%
Set the output resolution to 1920X1080
1080P.
Resolution: 1920x1080
50620%
Set the output resolution to1920X1200
WUXGA.
Resolution: 1920x1200
50621%
Set the output resolution to1600X1200
UXGA.
Resolution: 1600x1200
50624%
Set the output resolution to 1600X900.
Resolution: 1600x900
50632%
Get the output resolution.
Resolution: xx
(xx=1920×1200/1920×1080/
1600×1200/1360×768/1280×
800/1280×720/1024×768/16
00x900)
6.3.5 Output Image Adjusting
Command
Function
Feedback Example
502xx%
Set the brightness to xx.
Brightness: xx (xx=00~99)
50636%
Get the brightness.
Brightness: xx (xx=00~99)
6-input Seamless Scaler Switcher & HDBaseT Receiver
21
503xx%
Set the contrast to xx.
Contrast: xx (xx=00~99)
50637%
Get the contrast.
Contrast: xx (xx=00~99)
504xx%
Set the saturation to xx.
Saturation: xx (xx=00~99)
50638%
Get the saturation.
Saturation: xx (xx=00~99)
505xx%
Set the sharpness to xx.
Sharpness: xx (xx=00~99)
50639%
Get the sharpness.
Sharpness: xx (xx=00~99)
50607%
Auto-adjust the color temperature to xx.
Color Temperature: xxxx
(xx=Cool/Medium/Warm/Use
r)
50640%
Get the color temperature.
Color Temperature: xx (xx=
Cool/ Medium/Warm/User.)
50608%
Set the aspect ratio to xx.
Aspect Ratio: xx (xx= 16:9/
4:3/ auto)
50635%
Get the image aspect ratio.
Aspect Ratio: xx (xx= 16:9/
4:3/ auto/)
50614%
Set the image mode to xx.
Picture Mode: xx (xx=
dynamic/ standard/ mild/
user)
50633%
Get the image mode.
Picture Mode: xx (xx=
Dynamic/ Standard/ Mild/
User)
50655%
Freeze output image.
Freeze: enable
50656%
Cancel the freezing of output image
Freeze: disable
50753%
Get the freeze status.
Freeze: enable/Freeze:
disable
50646%
Display the volume icon.
Volume Icon: enable
50647%
Hide the volume icon.
Volume Icon: disable
50765%
Display the freeze icon.
Freeze Icon: enable
50766%
Hide the freeze icon.
Freeze Icon: disable
50644%
Enable input Icon status
Input Icon: enable
50645%
Disable input Icon status
Input Icon: disable
50650%
Get the Icon status.
Input Icon: enable/Input Icon:
disable
Volume Icon: enable/Volume
6-input Seamless Scaler Switcher & HDBaseT Receiver
22
Icon: disable
Freeze Icon: enable/Freeze
Icon: disable
50651%
Get Volume Icon display status.
Volume Icon: xxxx
50606%
Auto-adjust the input parameter(VGA
only)
VGA Input Auto
50678%
Enable screen output adjusting.
Enter Output Position Adjust
50679%
Disable screen output adjusting.
Exit Output Position Adjust
50670%
Move the image to right.
Output Position Adjust X xx
50671%
Move the image to left.
Output Position Adjust X xx
50672%
Move the image up.
Output Position Adjust Y xx
50673%
Move the image down.
Output Position Adjust Y xx
50674%
Stretch left from left side (increase image
width).
Output Width Adjust xx
50675%
Pull right from left side (decrease image
width)
Output Width Adjust xx
50676%
Stretch upwards from bottom side
(decrease image height).
Output Height Adjust xx
50677%
Stretch downwards from bottom side
(increase image height).
Output Height Adjust xx
50755%
Turn off HDMI output.
HDMI power off
50756%
Turn on HDMI output.
HDMI power off
50757%
Turn off HDBT output.
HDBT power off
50758%
Turn on HDBT output
HDBT power off
50759%
Turn on HDMI& HDBT output
synchronously.
HDMI HDBT power on
6.3.6 Auto Power-off Setup
Command
Function
Feedback Example
50713%
Auto Switch Mode: Disable the automatic
power off function.
Auto power off: Disable
50714%
Auto Switch Mode: Set the auto power-off
time to 0 minute when No signal input.
Auto power off: 0min
6-input Seamless Scaler Switcher & HDBaseT Receiver
23
50715%
Auto Switch Mode: Set the auto power-off
time to 1 minute when No signal input.
Auto power off: 1min
50716%
Auto Switch Mode: Set the auto power-off
time to 2 minute when No signal input.
Auto power off: 2min
50717%
Auto Switch Mode: Set the auto power-off
time to 5 minute when No signal input.
Auto power off: 5min
50718%
Auto Switch Mode: Set the auto power-off
time to 10 minute when No signal input.
Auto power off: 10min
50719%
Check the auto power-off time.
Auto power off: 5min
Manu power off: Disable
50771%
Manual Switch Mode: Disable auto
power-off time function.
Manu power off: Disable
50772%
Manual Switch Mode: Set the power-off
time to 1 minute.
Manu power off: 1min
50773%
Manual Switch Mode: Set the power-off
time to 2 minute.
Manu power off: 2min
50774%
Manual Switch Mode: Set the power-off
time to 5 minute.
Manu power off: 5min
50775%
Manual Switch Mode: Set the power-off
time to 10 minute.
Manu power off: 10min
50776%
Manual Switch Mode: Set the power-off
time to 0 minute.
Manu power off: 0min
6.3.7 OSD Menu Control
Command
Function
Feedback Example
50616%
MENU button (enter OSD)
OSD: Enter
50609%
OK for OSD selection
Key: ok
50610%
LEFT button
Key: left
50611%
RIGHT button
Key: right
50612%
UP button
Key: up
50613%
DOWN button
Key: down
50618%
EXIT button (exit OSD)
OSD: Exit
6-input Seamless Scaler Switcher & HDBaseT Receiver
24
6.3.8 CEC Input Commands
Command
Function
Feedback Example
50686%
Enable CEC Input.
HDMI CEC ON
50687%
Disable CEC Input.
HDMI CEC OFF
50901%
Play & pause.
CEC cmd: play&pause
50902%
Stop.
CEC cmd: stop
50903%
Menu.
CEC cmd: menu
50904%
Reverse.
CEC cmd: rev
50905%
Forward.
CEC cmd: fwd
50906%
Up.
CEC cmd: up
50907%
Down.
CEC cmd: down
50908%
Left.
CEC cmd: left
50909%
Right.
CEC cmd: right
50910%
Confirm command.
CEC cmd: select
50911%
Exit command Tog Menu.
CEC cmd: exit
50912%
Pause.
CEC cmd: pause
50913%
Power on input source device.
Source power on
50914%
Power off input source device.
Source power off
50915%
Enable input CEC auto power.
Source Auto Power Enable
50916%
Disable input CEC auto power.
Do not allow the Scaler Switcher to
power on from Blu-ray being powered on.
Source Auto Power Disable
6.3.9 CEC Output Commands
Command
Function
Feedback Example
50920%
Enable output CEC auto power.
When in switcher is in auto and video
detection is detected, CEC power on
command is sent to display. After 3
minutes of no video input, CEC power-off
command is sent to display.
Display Auto Power Enable
50921%
Disable output CEC auto power.
Disable Auto Power Disable
6-input Seamless Scaler Switcher & HDBaseT Receiver
25
50922%
Power on output display device.
Display Power On
50923%
Power off output display device.
Display Power Off
6.3.10 EDID Configuration
Command
Function
Feedback Example
50731%
Set 1-HDMI/MHL EDID to 720P.
HDMI1 EDID:720P
50732%
Set 1-HDMI/MHL EDID to 1080P.
HDMI1 EDID to:1080P
50733%
Set 1-HDMI/MHL EDID to 1920x1200.
HDMI1 EDID to:1920x1200
50735%
Set 2-HDMI EDID to 720P.
HDMI2 EDID:720P
50736%
Set 2-HDMI EDID to 1080P.
HDMI2 EDID:1080P
50737%
Set 2-HDMI EDID to 1920x1200.
HDMI2 EDID:1920x1200
50739%
Set 3-HDMI EDID to 720P.
HDMI3 EDID:720P
50740%
Set 3-HDMI EDID to 1080P.
HDMI3 EDID:1080P
50741%
Set 3-HDMI EDID to 1920x1200.
HDMI3 EDID:1920x1200
50743%
Set 4-HDMI EDID to 720P.
HDMI4 EDID:720P
50744%
Set 4-HDMI EDID to 1080P.
HDMI4 EDID:1080P
50745%
Set 4-HDMI EDID to 1920x1200.
HDMI4 EDID:1920x1200
50747%
Set DP EDID to 720P.
DP EDID:720P
50748%
Set DP EDID to 1080P.
DP EDID:1080P
50749%
Set DP EDID to 1920x1200.
DP EDID:1920x1200
50767%
Restore default EDID.
EDID:Default
50768%
Bypass EDID data from output to input.
EDID:Bypass
50769%
Upload custom EDID data to the
switcher.
EDID:User
50770%
Inquire EDID status.
EDID:Default/
EDID:Bypass/
EDID:User/
50782%
EDID management, copy the best
resolution data of one output to HDMI
input.
EDID manage
Resolution:1920x1080
6-input Seamless Scaler Switcher & HDBaseT Receiver
26
6.3.11 HDCP Compliance
Command
Function
Feedback Example
50791%
HDCP Active mode.
HDCP Active.
50792%
HDCP Manual mode.
HDCP Manual.
50793%
Enable HDCP output.
HDCP ON
50794%
Disable HDCP output.
HDCP OFF
50795%
Get HDCP status.
HDCP Active/HDCP Manual
HDCP ON/HDCP OFF
6.3.12 Device Setup
Command
Function
Feedback Example
50797%
Enter standby mode.
System Standby
50697%
Power on.
System Power On
50604%
Lock the front panel buttons.
Front Panel Lock
50605%
Unlock the front panel buttons.
Front Panel Unlock
50754%
Get the panel locked status.
Front Panel Lock/Front Panel
UnLock
50699%
Get the system version.
Version Vx.x.x
50698%
Software update.
Software update
50617%
Restore to factory defaults.
Factory Reset
50657%
Check IP address
192.168.0.178!
50783%
Get current status
Display status including Source, Line
audio, Resolution, Output Audio on/off,
Manual/ Auto-switching modes
Source Volume:XX (Source
xx = 00 to 60)
Line Volume:XX (Line xx =
00 to 60)
Input:XXXX
Resolution:XXXX
Embedded Audio Output:
XXXX(Enable/Disable)
Source Mute/Source Unmute
Line Mute/Line Unmute
6-input Seamless Scaler Switcher & HDBaseT Receiver
27
Auto Switch/Manual Switch
VGA Mute/Unmute
6-input Seamless Scaler Switcher & HDBaseT Receiver
28
7. OSD Menu Control
The Scaler Switcher provides a powerful OSD operation menu, including 3 parts:
optional settings, picture settings, and system setup.
There are three ways to enter OSD menu:
① Long-press the button MENU/3s on front panel 2 seconds or more.
② Press MENU button on IR Remote.
③ Send the command 50616% on RS232 Control Software.
Operation way:
Press direction buttons (Left/Right/Up/ down), ENTER button on front panel.
Press direction keys (Left/Right/Up/ down), OK key on IR Remote.
Sending OSD menu command via RS232 control software.
7.1 OPTIONS
Includes output adjust, input selection, baud rate, user EDID load (USB), resolution, and
software update (USB).
Output Adjust: Adjust output image position (X: horizontal direction and Y: vertical
direction), ratio aspect (width and height), polarity adjustment (H Polarity and V Polarity)
6-input Seamless Scaler Switcher & HDBaseT Receiver
29
and output setting (HDMI on/off and HDBT on/off).
Input Selection: Select video source format for VGA input, includes AV 1 (C-video
signal), VGA 1 (VGA signal) and YPbPr 1 (Component video signal).
Baud rate: Set the baud rate for RS232 control, and it support 2400、4800、9600、19200、
38400、57600、115200.
User EDID Load (USB): Insert the USB flash disk with EDID file to FIRMWARE port to
load EDID data through this menu.
Resolution: Set the output resolutions, and it support 1920x1200, 1920x1080,
1600x1200, 1600x900, 1360x768, 1280x800, 1280x720, 1024x768.
Audio Mute Setup: Turn on/off the Mix, 1-AUDIO, 2-AUDIO, HDMI 1, HDMI 2, HDMI 3,
HDMI 4, DP, VGA audio.
IP: Show the IP address.
Software Update (USB): Insert the USB flash disk with updating file to the FIRMWARE
port of the Scaler Switcher, to update the software through this menu.
7.2 PICTURE
Including picture mode, color temperature, aspect ratio.
Picture mode: Include Dynamic, Standard, Mild, and User. Only in User mode,
will it be able to set the image contrast, brightness, color and sharpness.
Color Temperature: Include Cool, Medium, Warm and User. And only in User
mode, it is able to set values for Red, Green and Blue (RGB).
6-input Seamless Scaler Switcher & HDBaseT Receiver
30
Aspect Ratio: Include Native, 4:3, 16:9, Zoom1, Zoom2, Just Scan, and
Panorama. VGA format only supports 4:3, 16:9 and Panorama.
7.3 SETUP
Including OSD language, restore factory default, HDMI CEC and version inquiry.
OSD Language: Supports 7 languages, including English (default), Chinese etc.
Restore Factory Default: Restores to original system state.
HDMI CEC: Enable/disable CEC and auto-standby function. Default: CEC on,
STANDBY on. Only when CEC is on, will it be able to set auto-standby status.
FW Ver. 1.0.0: Software version.
6-input Seamless Scaler Switcher & HDBaseT Receiver
31
8. Web-based GUI Control
In addition to control the Scaler Switcher via front panel button, IR remote and RS232
communication software. The Scaler Switcher can be controlled via web-based GUI. It
allows users to interact with the Scaler Switcher through graphical icons and visual
indicators.
Type 192.168.0.178 in your browser, it will enter the log-in interface shown as below:
8.1 Control Menu
Type the default user name (user) and password, and then click Login to enter the
Control menu shown as below:
6-input Seamless Scaler Switcher & HDBaseT Receiver
32
Sources: Click the corresponding button (1-HDMI/MHL, 2-HDMI, 3-HDMI, 4-HDMI,
5-DP and 6-VGA) to select video input source.
AUTO: Click this button to enter auto-switching mode.
Adjust: Click this button to adjust the position of VGA video output image to make
sure the best visual effect.
Display: Click this button to turn on/off output display device.
Standby: Click this button to let the Scaler Switcher into standby mode.
Volume: Click the corresponding positive/negative button or move the scroll bar to
turn up/down the MIX/Source audio volume.
Click the corresponding Mute button to mute/unmute Line/Source audio input.
6-input Seamless Scaler Switcher & HDBaseT Receiver
33
8.2 Configuration Menu
① Setting
Click on control menu to enter configuration menu shown as below:
Output Resolution: Select the output resolution.
Update: Insert the USB flash disk with EDID file/software updating file to the
FIRMWARE port, and then click EDID/Firmware to start update procedure.
Shutdown Timer(NO Input)：Set the auto power-off time or manual power-off time,
including none, 1 minute, 2minutes, 5minutes and 10 Minutes. If the Scaler
Switcher can’t detect video source input, it will automatically shut down after a
preset interval.
② Network
Click Network to enter the below menu to select the dynamic or static mode. Under
static mode, then IP address, subnet mask and gateway can be reset.
6-input Seamless Scaler Switcher & HDBaseT Receiver
34
③ Source
Click Source Label to enter the below menu to rename the input selection buttons.
6-input Seamless Scaler Switcher & HDBaseT Receiver
35
8.3 RS232 Control Menu
Click RS232 Control on the top of interface to enter the below menu to send commands
to control the Scaler Switcher or far-end third-party device.
Port: Local refers to the RS232 port of the Scaler Switcher, and HDBT refers to
the RS232 port of HDBaseT Receiver.
Baud Rate: The baud rate of local port is 9600, but for HDBT port, it support 2400、
4800、9600、19200、38400、57600、115200.
Command: Typing commands in this box to control the Scaler Switcher or the
far-end third-party device connected to HDBaseT Receiver. If check the “Hex”, you
can type RS232 commands with hexadecimal value in the “Command” box.
6-input Seamless Scaler Switcher & HDBaseT Receiver
36
8.4 Password Menu
Click Password on the top of interface to enter the below menu to reset the username
and password.
8.5 Web-based GUI Update
Web-based GUI for the Scaler Switcher supports online update in
http://192.168.0.178:100. Type the username and password (the same as the GUI log-in
settings, modified password will be available only after rebooting) to log in the
configuration interface. After that, click Administration at the source menu to get to
Upload Program as shown below:
Select the desired update file and press Apply, it will start upgrading then.
6-input Seamless Scaler Switcher & HDBaseT Receiver
37
9. Specification
9.1 Seamless Scaler Switcher
Video
Video Input
(1) HDMI/MHL; (3) HDMI; (1) DP; (1) VGA
Video Input Connector
(4) Female HDMI; (1) DisplayPort; (1) Female VGA
(15-pin)
Input Video Signal
HDMI, DP, YPbPr, C-video, VGA
Video Output
(1) HDMI; (1) HDBaseT
Video Output Connector
(1) Female HDMI; (1) RJ45
Output Video Signal
HDMI, HDBaseT
Output Resolution
1920x1200, 1920x1080, 1600x1200, 1600x900,
1360x768, 1280x800, 1280x720, 1024x768.
Standards
Compliant with HDMI 1.4 & HDCP2.2
Audio
Audio Input
(1) MIX; (2) AUDIO
Audio Input Connector
(1) 3-Pin phoenix connector
(2) 3.5mm Stereo jacks
Audio Input Impedance
>10kΩ
Audio Output
(1) Stereo balanced L/R audio
Audio Output Connector
(1) 5-Pin phoenix connector
Audio Output Impedance
70Ω
Frequency Response
20Hz~20K Hz
Stereo Channel Separation
>80dB @1KHz
Control Part
Control port
(1) IR IN, (1) IR OUT; (1) IR EYE; (1) FIRWARE;
(1) RS232; (1) TCP/IP
Control Connector
(3) 3.5mm mini jacks; (1) Type-A USB;
(1)3-Pin phoenix connectors; (1) RJ45
General
Transmission Distance
1080P≤70m
Temperature
-10℃ ~ +50℃
Humidity
10% ~ 90%
Power Supply
Input: AC 100~240V, 50/60Hz; Output: 24VDC 2.71A
Power Consumption
28W (Max)
Dimension (W*H*D)
250mm x 44mm x 200mm
Weight
970g
6-input Seamless Scaler Switcher & HDBaseT Receiver
38
9.2 HDBaseT Receiver
Video& Audio
Input
(1) HDBT IN
Output
(1) HDMI OUT; (1) AUDIO OUT; (1) COAX OUT; (1)
OPTICAL OUT
Control Ports
(1) IR IN, (1) IR OUT, (1) RS232
General
Transmission Mode &
Distance
HDBaseT; 1080P ≤ 70m; 4K×2K ≤ 40m
Resolution
Up to 4K×2K@60Hz 4:2:0
Bandwidth
10.2Gbps
HDMI Standard
HDMI1.4 & HDCP2.2
Power Consumption
10W (max)
Temperature
-10℃~ 50℃
Humidity
0% ~ 90%
Power Supply
Powered by the Seamless Scaler Switcher.
Dimension (W*H*D)
152mmx16.2mmx100mm
Net Weight (g)
223g
6-input Seamless Scaler Switcher & HDBaseT Receiver
39
10. Panel Drawing
10-1 Seamless Scaler Switcher
10-2 HDBaseT Receiver
VOLUME
IR
SOURCE
MIX
1-HDMI/ MHL 6-VGA
5-DP3-HDMI
4-HDMI2-H DMI AUTO
RES RESET /3sMENU/ 3sENTER
Tx Rx
DC 24V
HDBT
L R
HDMI1-HDMI/ MHL
IR EYEIR IN IR OUT TCP/IPRS232
AUDIO IN
1-AUDIO 2- AUDIO
L R
MIX
6-VGA2-HDMI 3-HDMI 4-HDMI 5-DP
CONTRO L AUDIO OU T POWER
INPUTS OUTPUT S
6-in put Se amless Scaler Switc her wi th HDBaseT6-in put Se amless Scaler Switc her wi th HDBaseT
250 mm
4
4
m
m
2
0
0
m
m
RS232
DC 12V
IR OUT
HDMI OU T
HDBT IN
AUDIO
OUT
OPTIC AL
OUT
IR IN
COAX
OUT
TPUH412RA
HDCPLINK
UPDATE A
CTRL
UPDATE B
Tx
Rx
152 mm
100 m
m
16.2 m
m
6-input Seamless Scaler Switcher & HDBaseT Receiver
40
11. Troubleshooting & Maintenance
Problems
Causes
Solutions
Output image with
snowflake
Bad quality of the
connecting cable
Try another high quality
cable.
Fail or loose connection
Make sure the connection
is good
No output image when
switching
No signal at the input /
output end
Check with oscilloscope or
multimeter if there is any
signal at the input/ output
end.
Fail or loose connection
Make sure the connection
is good
The switcher is broken
Send it to authorized
dealer for repairing.
POWER indicator doesn’t
work or no respond to any
operation
Fail connection of power
cord.
Make sure the power cord
connection is good.
EDID management does
not work normally
The HDMI cable is broken
at the output end.
Change for another HDMI
cable which is in good
working condition.
Static becomes stronger
when connecting the video
connectors
Bad grounding
Check the grounding and
make sure it is connected
well.
Cannot control the device
by control device (e.g. a
PC) through RS232 port
Wrong RS232
communication parameters
Type in correct RS232
communication
parameters.
Broken RS232 port
Send it to authorized
dealer for checking.
Cannot control the device
by front panel buttons while
can control it through
RS232 port
The front panel buttons are
locked
Send command 50605% to
unlock the front panel
buttons.
Cannot control the device
by RS232 / IR remote /
front panel buttons
The device has already
been broken.
Send it to authorized
dealer for repairing.
If your problem persists after following the above troubleshooting steps, seek further
help from authorized dealer or our technical support.
6-input Seamless Scaler Switcher & HDBaseT Receiver
41
12. After-sales Service
If there appear some problems when running this product, please check and deal with
the problems referring to this user manual. Any transport costs are borne by the users
during the warranty.
① Product Limited Warranty: We warrants that its products will be free from defects
in materials and workmanship for three years, which starts from the first day you
buy this product (The purchase invoice shall prevail).
Proof of purchase in the form of a bill of sale or receipted invoice which is evidence
that the unit is within the Warranty period must be presented to obtain warranty
service.
② What the warranty does not cover:
Warranty expiration.
Factory applied serial number has been altered or removed from the product.
Damage, deterioration or malfunction caused by:
Normal wear and tear
Use of supplies or parts not meeting our specifications
No certificate or invoice as the proof of warranty.
The product model showed on the warranty card does not match with the
model of the product for repairing or had been altered.
Damage caused by force majeure.
Servicing not authorized.
Any other causes which does not relate to a product defect
Delivery, installation or labor charges for installation or setup of the product.
③ Technical Support: Email to our after-sales department or make a call, please
inform us the following information about your cases.
Product version and name.
Detailed failure situations.
The formation of the cases.
Remarks: For any questions or problems, please try to get help from your local
distributor, or email EET at: obsupport@eet.dk
Loading...